Hunter Fanメーカー44100の使用説明書/サービス説明書
ページ先へ移動 of 33
OwnerÕ s Manual SINCE 1 8 8 6 ® 44100.
Other Quality Pr oducts fr om Hunter Fans Air Purifiers Humidifiers.
We are pleased you have selected one of our broad line of home comfort products. Our products are manufactured to high quality standards and are designed for years of service.
Read This Befor e Installing Thermostat IMPORT ANT 1 Read the entire installation section of this Owner ’s Manual thoroughly before you begin to install or operate your Hunter Thermostat. • Remove the mylar label from the display window . INST ALLA TION 2 All installation is normally performed at your thermostat.
This thermostat is designed to optimize the use of your heating and cooling equipment. It does this by matching your comfort (the temperatures in your home) to your schedule. An example: 6am – Y ou wake up. Program 1 has the heat set to 70° (21°C).
6-7 Featur es Manual switch for turning on heating and cooling system. Manual switch for automatic or continuous fan operation. Battery door for easy access Soft touch programming buttons (see below) Display shows time, day , temperature, program number , hold, usage and low battery indicator .
Changes the clock into 12 or 24 hour (military) mode. For entering minute of day . For revising and changing weekday or weekend programs T o reset filter counter back to zero. Returns display to current time and temperature. Automatically programs the thermostat for weekday and weekend program settings.
This thermostat comes with two #8 slotted screws and two wall anchors for mounting. T o install your unit, you should have the following tools and materials.
TYPICAL HOME THERMOST A TS FIGURE 1 W all Mounting Plate Thermostat Cover W all Mounting Plate Thermostat Cover.
■ Each wire coming from the wall to the existing thermostat is connected to a terminal point on that thermostat. Each of these terminal points is usually marked with a code letter as shown in T able A on page 1 1. ■ The number of wires in your system can be as few as two (for heat only systems), as many as eight, or any number in between.
Wir e Labeling RH G.
12-13 Installation NOTE: If your thermostat has one wire marked R or RH (4-wir e system), then leave the jumper wire between the RH and RC terminals. Otherwise, if you have separate RH and RC wir es (5-wire system), then r emove the jumper wire between the RH and RC terminals.
Snap open the wallplate from your thermostat by pressing the release tab on the bottom of the thermostat. Position wallplate on wall and pull existing wires through large opening. Then level for appearance. Mark holes for plastic anchors provided if existing holes do not line up with Hunter Thermostat holes.
The heating system selector and the F°/C° selector switches are located on the Printed Circuit Board. ■ Heating system selector The heating system selector is a switch on the Printed Circuit Board on the inside of the thermostat. The switch is at “HG” position.
FIGURE 3 FIGURE 4 W RC RH Y G ■ Be sure to tighten the terminal screws securely , otherwise a loose wire could cause operational problems with your system or thermostat. ■ Push excess wire back into hole to prevent interference with mounting of the thermostat cover .
Pr ogramming 1 Remove mylar label covering display window . 2 When the heating or cooling system is actually operating, “HEA T” or “COOL” will appear on the display . 3 If power is interrupted the batteries will keep all programs. 4 If “LOW BA TT” indicator appears on the display replace the batteries.
■ Press and hold until current hour appears on display . ■ Note the AM/PM indicator . ■ Press and hold until current minutes appear on display . ■ Press until current day appears on display . ■ Returns to normal time and temperature. ■ If return is not pressed it will return automatically in 10 seconds.
Pr ogramming Studies conducted by the Department of Energy estimate that setting your thermostat back 10°F for two 8-hour periods during winter can reduce your fuel bill by as much as 30%. By setting your thermostat up 5° for two 8-hour periods during summer you can reduce your fuel bill up to 25%.
NOTE: The thermostat program will NOT take effect immediately after programming of your thermostat but at the next programmed time/temperatur e change.
Pr ogramming Before programming or changing the program, use this Personal Program Schedule to determine which times and temperature settings will best satisfy both your comfort and energy saving requirements. Use a pencil so you can revise your records each time you change your temperature settings.
Y our thermostat can be programmed in two different ways. 1. Autoprogram method 2. Manual method Before programming, position the Heat/Off/Cool selector to the mode to be programmed. Autoprogram method In autoprogram method, you can program your thermostat instantly for the entire week by simply pressing “Auto Prog.
Pr ogramming W eekday Pr ograms Step 1 Step 2 ■ Normal display of time, temper- ature, and day of the week. ■ Program indicator (1) is displayed. ■ 68°F is displayed.
Step 3 Continue for W eekend Pr ograms ■ Press on once to change temperature to 69°F . ■ Weekday program 1 is complete. ■ Press PROG to move to program 2, 3, and 4 and follow the same steps Press to move to weekend programs. Weekends can be programmed with one schedule, or different schedules for Saturday and Sunday .
Pr ogramming W eekday Pr ogram ■ Normal display of current time, temperature, and day of week. ■ 1st weekday program is displayed. ■ Program indicator (1) appears.
T o Review The Curr ent T emperature Setting: Press for 2 seconds or less: or ■ Current time and temperature M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 15 68 c AM PM HEAT COOL 1 2 34 FILTER LO BAT ■ 70 indicates the current setting of the thermostat is 70°F .
Pr ogramming ■ Press arrow to display current set and room temperatures. M T W TH F SA SU 89 : 68 60 c AM PM HEAT COOL 1 2 34 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 89 : 70 60 c AM PM HEA.
In the event you wish to hold your manual override for vacation or an extended period of time, follow the temporary manual override instructions on page 26, then immediately press HOLD/CLEAR. This will maintain override setting indefinitely . “HOLD” will appear on the display .
Operations 72 . 7I . 70 . Filter Monitor T o Reset the Filter Counter to Zer o ■ Filter indicator disappears. M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 30 6 8 c AM PM HEAT COOL 1 234 FILTER LO BAT M.
Other Featur es Y our thermostat is preprogrammed at the factory to cycle when the temperature rises 1° above or 1° below the temperature setting to provide maximum comfort.
T roubleshooting Pr oblem Solution SCRAMBLED OR DOUBLE DISPLA Y (numbers over numbers) NO DISPLA Y ENTIRE DISPLA Y DIMS PROGRAM DOES NOT CHANGE A T YOUR DESIRED SETTING AUTO/F AN DOES NOT COME ON 1. Remove clear mylar sticker . 1. Check battery connections and batteries.
Pr oblem (Continued) Solution (Continued) If you experience any other problems, call 1-901-745-9222 from 8AM to 5PM Central Standard time for technical assistance. 1. Check that function switch is in correct position (“HEA T” or “COOL”). 2. There may be as much as 20 seconds delay in the thermostat turning the system on - wait and check.
Wiring Diagrams 32 4-wire Heat/Cool System 5-wire Heat/Cool System THERMOST A T G W Y RH RC Heat Relay or V alve Heat /Cool T ransformer Fan Relay Cool Contactor Jumper THERMOST A T G W Y RH RC Heat R.
2-wire Heat Only 3-wire Cool Only 3-wire Heat Only THERMOST A T G W Y RH RC Heat Relay or V alve Heat T ransformer THERMOST A T G W Y RH RC Heat Relay or V alve Heat T ransformer Fan Relay THERMOST A .
デバイスHunter Fan 44100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan 44100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan 44100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan 44100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan 44100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan 44100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan 44100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan 44100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan 44100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
