Hunter Fanメーカー51062の使用説明書/サービス説明書
ページ先へ移動 of 17
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 14 PA G E 10 PA G E 5 PA G E 17 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Installation Lad.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you.
T ools Needed P ower Drill (optional) Ladder 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers Mounting Options 1. Y ou will need a Longer Downrod sold separately 2.
1.888.830.1326 www .HunterF an.com 4 Mounting Options (c ontinued) Use Standard or L ow-Prole Mounting to hang the fan from a at ceiling by a standard downrod (included). Use Angled Mounting t o hang the fan from a vault ed or angled ceiling (see previous page).
1.888.830.1326 www .HunterF an.com C eiling Bracket Installa tion OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak.
www .HunterF an.com 1.888.830.1326 C eiling Bracket Installa tion (continued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks fr om the motor . Sav e the ve scre ws. The y will be needed for blade iron installation.
1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling St.
KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od.
1.888.830.1326 9 M0001-01 • 08/03/12 • © Hunter F an Compan y www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy .
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket.
www .HunterF an.com 1.888.830.1326 11 M0001-01 • 08/03/12 • © Hunter F an Compan y Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown.
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes.
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing .
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install the bulbs into the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 16 Maintenanc e & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off . T o switch the direc tion of air ow , mov e the reverse switch to the opposite position.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 17 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated .
デバイスHunter Fan 51062の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan 51062をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan 51062の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan 51062の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan 51062で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan 51062を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan 51062の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan 51062に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan 51062デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
