Hunter Fanメーカー53117の使用説明書/サービス説明書
ページ先へ移動 of 20
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 10 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Downrod PA.
www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician.
T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 4 M0069-01 • 04/30/13 • © Hunter F an Company 4 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak.
www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the screws . They will be needed for blade iron installation. Note: Some fans will hav e a shipping ring instead of shipping blocks.
1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling St.
KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od.
1.888.830.1326 9 M0069-01 • 04/30/13 • © Hunter F an Company www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy .
www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x.
www .HunterF an.com 1.888.830.1326 11 M0069-01 • 04/30/13 • © Hunter F an Company Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown.
www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching .
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing .
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) Install a light bulb in each socket. Note: Do not use CFL bulbs to replace your light bulbs . Y our lights may icker or fail to work. No te: Glass shade styl e and number of lights may vary .
www .HunterF an.com 1.888.830.1326 Remote C ontrol ON T urn P ow er Note: The remote must be pair ed before the fan will operate . Within 3 minutes of rest oring power to the fan, press both the F an Off button and the High button for at least 4 seconds .
www .HunterF an.com 1.888.830.1326 Remote C ontrol (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Push the light button on the r emote transmitter . Pull the light chain once . If the light does not turn on, repeat step . Push the 3 button on the r emote transmitter for high fan speed.
www .HunterF an.com 1.888.830.1326 Rocker- Style Plate Switch C over Plate Removed T abs T o install the transmitter cradle, remo ve the two screws holding the switch c over plate. Do not remov e the cover plate. Orient the cr adle by lining up the two mounting holes with those on the cov er plate.
www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company 19 F or cleaning the fan, use sof t brushes or cloths to prevent scr atching. Cleaning products may damage the nishes. Safe-Exit • Press the F an O ff button for at least three sec onds to initiate the Safe-Exit Mode .
www .HunterF an.com 1.888.830.1326 M0069-01 • 04/30/13 • © Hunter F an Company 20 T roubleshooting Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specications on the light sockets.
デバイスHunter Fan 53117の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan 53117をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan 53117の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan 53117の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan 53117で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan 53117を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan 53117の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan 53117に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan 53117デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
