Hunter FanメーカーM0099-01の使用説明書/サービス説明書
ページ先へ移動 of 19
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 10 PA G E 5 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy O.
www .HunterF an.com 1.888.830.1326 M0099-01 • 05/06/14 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you .
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 4 M0099-01 • 05/06/14 • © Hunter F an Company If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) .
www .HunterF an.com 1.888.830.1326 C eiling Bracket Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
www .HunterF an.com 1.888.830.1326 Prepar ation D I S C A R D K E E P ! Remove the shipping blocks fr om the motor . Sav e the screws . They will be needed for blade iron installation. Note: Some fans will hav e a shipping ring instead of shipping blocks.
www .HunterF an.com 1.888.830.1326 7 M0099-01 • 05/06/14 • © Hunter F an Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings.
www .HunterF an.com 1.888.830.1326 8 M0099-01 • 05/06/14 • © Hunter F an Company KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops.
www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan.
www .HunterF an.com 1.888.830.1326 Wiring T urn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet bo x.
www .HunterF an.com 1.888.830.1326 Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag.
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes.
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 14 M0099-01 • 05/06/14 • © Hunter F an Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the light xture falling.
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) Connect the appropriate pull chain pendant to each of the short chains coming from the nial and nial cap .
www .HunterF an.com 1.888.830.1326 Remote C ontrol Note: The remote must be pair ed before the fan will operate . Within 3 minutes of rest oring power to the fan, press both the F an OFF button and the F an ON button for at least 4 seconds . Y our fan will turn on to indicate successful syncing.
www .HunterF an.com 1.888.830.1326 17 M0099-01 • 05/06/14 • © Hunter F an Company F an Operation: Press and quickly release the ON or OFF button on the remote control t o turn the fan OFF or ON. T o change the fan speed, slowly pull the fan pull-chain switch to select the desired speed .
www .HunterF an.com 1.888.830.1326 Opera tion, Maintenance , & Cleaning (con tinued) Changing the bulbs - unscrew the nial and remo ve it from the threaded rod . Remove the nial cap and unscrew the globe keeper while suppor ting the globe with your other hand .
www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . Noisy Operation • Tighten the blade and blade iron screws until they are snug .
デバイスHunter Fan M0099-01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan M0099-01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan M0099-01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan M0099-01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan M0099-01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan M0099-01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan M0099-01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan M0099-01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan M0099-01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
