Hunter FanメーカーM3559-01の使用説明書/サービス説明書
ページ先へ移動 of 18
www .HunterF an.com 1.888.830.1326 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Pla te Ladder PA G E 3 T ools Needed Hanging the F an PA G E 9 Canop y T able of C ontents P.
www .HunterF an.com 1.888.830.1326 w .1 - T o reduce the risk of re , elec trical shock, or personal injury , mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet bo x.
www .HunterF an.com 1.888.830.1326 T ools Needed Po wer Drill (optional) 9/64” Drill Bit (optional) Ladder Screwdrivers Wire Strippers If mounting to a support structure, you will also need these tools .
www .HunterF an.com 1.888.830.1326 4 M3559-01 • 11/12/14 • © Hunter F an Company C eiling Plate Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
www .HunterF an.com 1.888.830.1326 5 M3559-01 • 11/12/14 • © Hunter F an Company T op Housing Rest the trim ring on the top housing. T rim Ring Thread the wires through the top housing . Place the canopy on the top housing. Ensur e all four screw holes line up with the screw holes in both the top housing and the adapter .
www .HunterF an.com 1.888.830.1326 Install the top housing screws. Install the grounding screw in the smaller screw hole. T hese screws can be found in the hardware bag .
www .HunterF an.com 1.888.830.1326 Hanging the F an Raise the fan and align the slots in the canopy with the hooks on the ceiling plate . No te: Fan style may vary .
www .HunterF an.com 1.888.830.1326 F R O M F A N Wiring White Black (Grounded) Note: T o connect the wires , hold the bare metal leads together and place a wire connector ov er them, then twist clockwise until tight.
www .HunterF an.com 1.888.830.1326 9 M3559-01 • 11/12/14 • © Hunter F an Company Canop y Partially install a canopy screw , found in the hardware bag , between the ceiling plate hooks. When all the holes are properly aligned , securely tighten all three canopy screws .
www .HunterF an.com 1.888.830.1326 Using both hands, push the canop y trim ring up to the top of the canopy . The canopy trim ring will snap and lock into place . Note: Should you need to r emove the trim ring, press rmly on opposite sides of the trim ring .
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents may damage the nishes.
www .HunterF an.com 1.888.830.1326 S witch Housing Remove the pr e-installed screw and red label from the switch housing . SA VE THE SCREW . Note: The screw was installed f or shipping purposes only . F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise.
www .HunterF an.com 1.888.830.1326 13 M3559-01 • 11/12/14 • © Hunter F an Company S witch Housing (continued) Insert the third screw , found in the hardware bag , into place and then tighten all three (3) screws . Connect the plugs from the upper and lower switch housings .
www .HunterF an.com 1.888.830.1326 S witch Housing (continued) Align the keyhole slots in the lower switch housing with the stand off screws. T urn the housing counterclockwise until the standoff screws are rmly situated in the narrow end of the keyhole slots.
www .HunterF an.com 1.888.830.1326 15 M3559-01 • 11/12/14 • © Hunter F an Company Light Kit Lift the cover plate , aligning the screw holes with the screw holes in the switch housing. Install the plat e screws to secure the cov er plate to the switch housing.
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of the short chains coming from the switch housing .
www .HunterF an.com 1.888.830.1326 Maintenanc e, Oper ation, & Cleaning Cleaning the fan - Use soft brushes or cloths to prevent scratching . Cleaning products may damage the nishes. T o switch the direc tion of air ow , mov e the reverse switch to the opposite position.
www .HunterF an.com 1.888.830.1326 T roubleshooting Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specications on the light sockets. F an doesn’ t work • Make sure power switch is on.
デバイスHunter Fan M3559-01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Hunter Fan M3559-01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHunter Fan M3559-01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Hunter Fan M3559-01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Hunter Fan M3559-01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Hunter Fan M3559-01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHunter Fan M3559-01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Hunter Fan M3559-01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHunter Fan M3559-01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
