Husqvarnaメーカー10527SB-LSの使用説明書/サービス説明書
ページ先へ移動 of 40
10527SB-LS Owner's Manual / 96193003700.
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
5 AS SEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely .
6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
7 AS SEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI (19-24.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power -pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow).
10 OPERA TION TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow .
11 TO MOVE FORWARD AND BACK WARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system.
12 OPERA TION SCRAPER BAR The scraper bar is not adjustable, but is reversible. After con sid er able use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement.
13 OPERA TION TO ST ART ENGINE Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C.
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
15 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
16 SERVICE AND ADJUSTMENTS CHUTE DEFLECTOR The chute deflector , attached to the top of the discharge chute, is provided to direct discharging snow away from the operator . If the deflector becomes damaged, it should be re placed. WARNING: T o avoid serious injury , nev er operate your snow thrower with the deflector removed or damaged.
17 SERVICE AND ADJUSTMENTS 7. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.
18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refill fuel tank with fresh, clean gasoline.
20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 2 (EXPLODED) 2 10 9 1 11 11 3 12 12 4 13 14 15 17 8 7 11 5 6 11 16 18 35 19 21 22 23 24 25 23 22 21 20 36 26 27 28 30 29 31 31 32 33 34 01.
21 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
22 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S.
23 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 1 2 3 3 2 01.11.002-A 1 532 40 78-34 SKID PL A TE 2 872 27 05-06 CARRIAGE BOL T 5/16 − 18 X .
24 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
25 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
26 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
27 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
28 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
29 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
30 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
31 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 01.02.001-F_Sheet_1 1 2 1 3 4 5 6 5 7 8 9 10 11 12 1 2 3 2 1 28 2 2 14 13 14 14 2 2 2 28 15 3 1 1 16 3 1 1 2 20 17 18 19 4 4 8 8 23 24 27 25 27 21 28 28 22 26 KEY P ART NO .
32 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 01.02.001-F_Sheet_2 1 2 2 3 4 5 6 7 7 8 7 9 10 11 12 13 14 15 15 16 17 8 17 18 19 20 21 26 23 27 22 13 15 24 25 28 33 32 30 31 29 14 15 15 34 35 36 37 38 39 41 20 32 40 43 41 20 32 42 44 NOTE: All component dimensions given in U.
33 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
34 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
35 REP AIR P ARTS CHAS SIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .
36 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS WHEELS SNOW THROWER - MODEL NO .
37 REP AIR P ARTS WHEELS SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts.
38 REP AIR P ARTS BAG OF P ARTS SNOW THROWER - MODEL NO . 10527SB-LSb 10527SB-LSb (96193003700), PRODUCT NO. 961 93 00-37 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.
39 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty .
532 42 35-13 09.23.08 SBW Printed in the U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free fro.
デバイスHusqvarna 10527SB-LSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 10527SB-LSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 10527SB-LSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 10527SB-LSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 10527SB-LSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 10527SB-LSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 10527SB-LSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 10527SB-LSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 10527SB-LSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
