Husqvarnaメーカー10530SBEBの使用説明書/サービス説明書
ページ先へ移動 of 32
10530SBEB Owner's Manual.
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engineered and man ufactured to give best possible dependability and per formance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center/department.
4 P ARTS P ACKED SEP ARA TEL Y IN CART ON.
5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 ASSEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.
7 ASSEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinfl ated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI.
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Choke control - used for starting a cold engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . LH and RH turn triggers - used to steer the snow thrower . Defl ector remote control lever - used to change the distance the snow is thrown.
10 TO USE CHOKE CON TROL (See Fig. 12) The choke con trol is located on the en gine. Use the choke control when ever you are starting a cold en gine. Do not use to start a warm en gine. • T o engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.
11 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system.
12 TO ADJUST SKID PLA TES (See Fig. 18) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface.
13 COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place ON / OFF switch in “ON” position.
14 MAINTENANCE LUBRICA TION CHART GENERAL REC OMMENDA TIONS The warranty on this snow thrower does not cover items that have been sub jected to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in structed in this manual.
15 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad justable. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
16 W ARNING: T o avoid serious injury , before per- forming any service or ad justments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.
17 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 22) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center .
18 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a furnace, water heater , clothes dryer or gas ap pliance.
19 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline.
20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 6 6 6 5 9 12 7 8 6 11 27 57 10 10 13 4 14 16 15 36 37 50 47 42 42 44 27 .
21 KEY P ART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Assembly , Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-55 Bolt, Flat Head, Carriage 5/16-18 x 5/8.
22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 3 2 1 2 6 19 2 2 26 28 27 27 25 20 29 31 30 7 4 5 6 8 8 16 18 17 10 14 3 1.
23 KEY P ART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 19 84-75 Control Assembly , Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer , Flat.
24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 41 27 22 17 11 15 15 14 38 39 40 37 33 35 35 .
25 KEY P ART NO. NO. DESCRIPTION 1 532 18 41-10 Lever , Auger Control, RH 2 532 18 41-09 Lever , T raction Drive Control, LH 3 532 19 96-39 Nut, Cage 1/4-20 4 532 17 88-88 Bushing, Flange 5 532 16 96-.
26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 4 4 4 1 2 5 3 5 1 2 3 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 3 42 42.
27 KEY P ART NO. NO. DESCRIPTION 1 532 14 63-15 Screw , Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15 Washer , Flat 4 817 49 05-08 Screw , Hex Head 5/16-18 x 1/2 5 532 18 00-1.
28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 6 20 14 47 47 48 4.
29 KEY P ART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, T raction Idler 2 532 18 05-22 Pulley , Idler (2-1/4) 3 - - - Engine, Briggs & Stratton, Model Number 20E1 14 (For engine service and replac.
30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 10530SBEB (96193001300), PRODUCT NO. 961 93 00-13 7 32 30 32 30 15 18 17 19 13 20 11 27 27 19 16 20 11 14 15 12 13 18 14 12 4 4 31 34 34 2 8 .
31 KEY P ART NO. NO. DESCRIPTION 1 532 19 95-01 Wheel Assembly , 12", Power Steering, LH 2 532 15 54-43 Pin, Klik 1/4 3 532 19 21-09 Cover , Power Steering 4 532 18 44-71 Bolt, Shoulder #10-24 x .
532 40 37-62 Rev . 3 06.06.06 BY Printed in U.S.A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur- c.
デバイスHusqvarna 10530SBEBの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 10530SBEBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 10530SBEBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 10530SBEBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 10530SBEBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 10530SBEBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 10530SBEBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 10530SBEBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 10530SBEBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。