Husqvarnaメーカー1152450-26の使用説明書/サービス説明書
ページ先へ移動 of 20
E E E E n n n n g g g g l l l l i i i i s s s s h h h h K3000 K3000 W et Oper ator ′ s manual Please read the operator’ s manual car efully and mak e sure y ou understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ..........................................
4 – English WHA T IS WHA T? What is what on the power cutter - K3000? 1 2 3 4 5 6 7 8 10 11 12 14 15 9 6 13 1 Rear handle 2 Guard f or the blade 14” 3 Cutting blade 4 Locking the axle 5 F ront han.
English – 5 WHA T IS WHA T? What is what on the power cutter - K3000 W et? 1 Rear handle 2 Guard f or the blade 3 W ater kit 4 Cutting blade 5 Locking the axle 6 F ront handle 7 Inspection cov ers 8.
6 – English SAFETY INSTR UCTIONS Steps before using a ne w power cutter • Please read the operator’ s manual carefully and make sure you understand the instructions bef ore using the machine. • The machine is only designed f or cutting hard materials, such as concrete, brick, masonry as well as cast iron and cement pipes.
English – 7 SAFETY INSTR UCTIONS General safety warnings Sav e all warnings and instructions for future ref erence. The term ”power tool” in the warnings refers to y our mains- operated (corded) pow er tool or batter y-operated (cordless) power tool.
8 – English SAFETY INSTR UCTIONS P ersonal saf ety • Sta y aler t, watch what you are doing and use common sense when operaing a pow er tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating pow er tools may result in serious personal injur y .
English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s safety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine .
10 – English SAFETY INSTR UCTIONS Cutting blades General • Cutting blades are a vailab le in two basic designs; abrasiv e discs and diamond blades .
English – 11 SAFETY INSTR UCTIONS Diamond blades Diamond blades consist of a steel body pro vided with segments that contain industrial diamonds. Diamond blades ensure lo wer costs per cutting operation, f ewer b lade changes and a constant cutting depth.
12 – English SAFETY INSTR UCTIONS General working instructions Cutting technique The technique described below is of a general character . Check inf or mation for each b lade regarding individual cutting characteristics (for e xample, diamond blades requires less f eeding pressure than an abrasive discs).
English – 13 SAFETY INSTR UCTIONS General rules • Ne ver start to cut with the upper quadrant of the blade as shown in the figure , also known as the kickbac k zone . • Alwa ys hold the machine in a firm grip with both hands. Hold it so that the thumbs and fingers grip round the handles.
14 – English ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed for hand-held po wer cutters. Blades are manuf actured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1").
English – 15 ST AR TING AND ST OPPING Bef ore star ting K3000 We t W ater connector • Connect the water hose to the w ater supply (A). The water is s witched on and off with the water tap (B). Star ting • Grip the front handle with the left hand.
16 – English MAINTENANCE General Cleaning Cooling system The machine is equipped with an efficient f an to cool the motor . Cooling air which is drawn in through the g rille by the machines rear handle passes ov er the stator and rotor and out through the front of the motor housing.
English – 17 MAINTENANCE Bevel gear The grease in the gear housing should be changed e very 4 months. Use high quality gear grease The gear housing must not be filled completely with grease . The grease e xpands as the machine heats up during operation.
18 – English TECHNICAL D A T A ´®z+TM"¶6}¨ ´®z+TM"¶6}¨ Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment Max.
English – 19 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the pow.
´®z+TM"¶6}¨ 2009-05-05 ´®z+TM"¶6}¨ 1152450-26.
デバイスHusqvarna 1152450-26の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 1152450-26をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 1152450-26の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 1152450-26の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 1152450-26で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 1152450-26を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 1152450-26の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 1152450-26に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 1152450-26デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。