Husqvarnaメーカー1153286-26の使用説明書/サービス説明書
ページ先へ移動 of 36
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 324LD X-series Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.
KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual.
CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ................................................................ 2 CONTENTS Contents ......................
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets .
English – 5 WHA T IS WHA T? What is what? 1 T rimmer head 2 Bev el gear 3 Grease filler cap, be vel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Stop switch 8 Throttle control 9 Throttle.
GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal protective equipment HEARING PR O TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection. If you use a visor then you must also w ear approved protectiv e goggles.
GENERAL SAFETY PRECA UTIONS English – 7 CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear je weller y , shor ts sandals or go barefoot. Secure hair so it is abo ve shoulder lev el.
GENERAL SAFETY PRECA UTIONS 8 – English be chec ked. See instructions under the heading Maintenance. Stop s witch Use the stop s witch to switch off the engine . Star t the engine and mak e sure the engine stops when you mov e the stop switch to the stop setting.
GENERAL SAFETY PRECA UTIONS English – 9 Muffler The muffler is designed to keep noise le vels to a minimum and to direct exhaust fumes a way from the user . A muffler fitted with a catalytic conv er ter is also designed to reduce harmful exhaust gases.
GENERAL SAFETY PRECA UTIONS 10 – English The nylon lining inside the locking n ut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. 10 times .
ASSEMBL Y English – 11 Fitting the loop handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw .
ASSEMBL Y 12 – English Fitting a trimmer guar d and Superauto II 1” trimmer head • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft.
FUEL HANDLING English – 13 Fuel handling Nev er star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilt fuel on yourself or y our clothes, change your clothes. W ash any par t of y our body that has come in contact with fuel.
FUEL HANDLING 14 – English When the oil lev el is low , top up using engine oil to the edge of the oil refill hole. Only use recommended engine oil. Fuelling Clean around the fuel cap. Clean the fuel and oil tank regularly . The fuel filter should be changed at least once a year .
ST AR TING AND ST OPPING English – 15 Check bef ore star ting • Check that the support flange is not cracked due to fatigue or due to being tightened too m uch. Discard the suppor t flange if it is crack ed. • Ensure the locking nut has not lost its captiv e force.
ST AR TING AND ST OPPING 16 – English W arm engine Ignition: Set the stop s witch to the star t position. Choke: Put the choke in working position. Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb . The b ulb need not be completely filled.
W ORKING TECHNIQ UES English – 17 General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine.
W ORKING TECHNIQ UES 18 – English Basic working tec hniques Alwa ys slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the ground at an angle.
MAINTENANCE English – 19 Carburettor Function • The carburettor gov erns the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor . • Setting the carburettor in volves adapting the engine to suit local conditions, e.
MAINTENANCE 20 – English Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder .
MAINTENANCE English – 21 If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter . Oiling the air filter Alw a ys use HUSQV ARNA filter oil, ar t. no. 531 00 92-48.
22 – English MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carr y out the maintenance and ser vice work described in this Operator’s Manual.
English – 23 TECHNICAL D A T A T ec hnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/ EC. Reported sound power le vel for the machine has been measured with the original cutting attachment that gives the highest lev el.
24 – English TECHNICAL D A T A The follo wing attachments are recommended for the specified models. The follo wing attachments have been de veloped mainly f or the Husqvarna 125LD tr immer , but can also be used with the specified models.
1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
.
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
T35, T35x "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
.
.
.
.
.
.
Original instructions ´®z+U<^¶6_¨ ´®z+U<^¶6_¨ 2010-03-31 1153286-26.
デバイスHusqvarna 1153286-26の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 1153286-26をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 1153286-26の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 1153286-26の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 1153286-26で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 1153286-26を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 1153286-26の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 1153286-26に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 1153286-26デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
