Husqvarnaメーカー1200の使用説明書/サービス説明書
ページ先へ移動 of 40
101 89 37-26 Rider 1 030 BioClip Rider 1 20 0 Operator´ s manual Please read these instructions carefully and make sure you understand them before using the machine.
Svenska – 31 Sve-5 225/232/235 Bruk 97-11-25, 08.46 31.
English – 1 Safety instructions ............................................. 2 Safety rules for USA ........................................ 2 Explanation of symbols ..................................... 4 Safety instructions ......................
2 – English SAFETY INSTRUCTIONS 1. Safety rules f or USA Safe operation practices for ride-on mowers IMPORT ANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to ob- serve the following safety instructions could result in serious injury or death.
English – 3 SAFETY INSTRUCTIONS IV . Service 1. Use extra care in handling gasoline and other fuels. They are flammable and vapours are explosive. a) Use only an approved container . b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refuelling.
4 – English Never carry passengers on the machine or equipment Speed limiter pedal forwards Neutral Speed limiter pedal reverse Starting instructions Read the instructions Check the engine’s oil l.
English – 5 RIDER 970 RIDER 970 RIDER 970 These instructions are for your safety . Read them carefully . SAFETY INSTRUCTIONS This symbol implies that important safety rules are applicable. This is for your safety and the operating reliability of the machine.
6 – English • W atch out for traffic when working close to a road, or crossing one. • Be careful when rounding a fixed object so that the blades do not hit it. Never drive intentionally over a foreign object. • The machine is heavy and can cause very severe crush injuries.
English – 7 Do not do the following: • Avoid unnecessary turns on slopes, and if turning is necessary turn slowly and gradually , downwards if possible. • Do not cut close to edges, ditches or banks. The machine can suddenly tip over if a wheel goes over the edge of a drop or a ditch, or if a bank gives way .
8 – English • Check the fuel level each time before using the machine, and leave space for the fuel to expand since the heat from the engine and hot sun can cause the fuel to run over . • Avoid overfilling. If petrol has been spilt on the machine wipe it up and wait until it has evapor- ated before starting the engine.
English – 9 Presentation These instructions describe two machine models, Rider 1030 Bioclip and Rider 1200. Rider 1030 Bioclip and Rider 1200 are fitted with Vanguard V-Twin engines from Briggs & Stratton of 18 h.p. Rider 1030 has a cutting unit with Bioclip function and a mowing width of 1030 mm.
10 – English Throttle control The throttle control regulates the engine speed, and thereby also the rotation speed of the blades. To increase or reduce the engine speed the control is moved forwards or backwards. Choke lever The choke lever is used for cold starting and to give the engine a richer fuel mixture.
English – 11 Cutting unit Rider 1030 has a Bioclip unit which cuts the grass finely by cutting it several times before it is returned to the lawn as fertiliser . The cutting unit on Rider 1200 has rear ejection, i.e. the grass cuttings are thrown out behind the cutting unit.
12 – English PRESENT A TION Lever for adjustment of the cutting height The cutting height can be adjusted to 7 different positions with the cutting height lever. T o achieve an even cutting height it is important that the tyre pressures are the same on the front wheels (60 kPa).
English – 13 Before starting • Read the safety instructions and information on the location and function of the controls before starting (see pages 5–12). • Conduct daily maintenance before starting (see maintenance schedule on page 17). • Adjust the seat to the required position.
14 – English DRIVING 5. When the engine starts release the ignition key immediately back to neutral position. IMPORTANT INFORMATION Do not run the starter for more than about 5 seconds at a time. If the engine does not start, wait about 10 seconds before trying again.
English – 15 3. Select the required cutting height (1–7) with the cutting height lever . 4. Push in the lock button on the lift lever and lower down the cutting unit. Cutting tips • Localise and mark stones and other fixed objects to avoid collision.
16 – English DRIVING ! W ARNING! Never drive the machine on ground at an angle of more than 15°. Mow slopes upwards and downwards, never across. A void sudden changes in direction. MAX 15 Stopping the engine Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard.
English – 17 25 50 100 300 MAINTENANCE ! Check the engine’s oil level 19 ● Check the engine’s cooling air inlet 19 ● Check the fuel pump’s air filter 19 ● Check the transmission’s air .
18 – English Dismantling of the machine hoods Engine hood Release the two rubber straps on the rear edge of the engine hood and lift off the hood. Front hood Dismantle the screws (1, 2 and 3) and lift off the front hood. Right-hand fender Dismantle the foot-plate (1), screws (2 and 3), and lift off the fender .
English – 19 Check the engine’ s oil level Check the oil level in the engine when the machine is horizontal. Dismantle the engine hood as per the description on page 18. Take out the dip stick, wipe off the oil, and insert again. The dip stick must be fully screwed down.
20 – English Check the transmission’ s air intake Check that the transmission’s air intake in not blocked. Check the transmission’ s oil level 1. Check the transmission’ s oil level by looking through the mesh on the air intake. The oil level should lie between the MIN and MAX markings on the oil canister at 20° C.
English – 21 Checking and adjustment of the steering wires The steering is controlled by means of wires. These can in time become slack, which implies that the adjustment of the steering becomes altered. Check and adjust the steering as follows: 1. Dismantle the frame-plate by releasing the screws (two on each side).
22 – English Checking and adjusting the brake Check that the brake is correctly adjusted by placing the machine on a slight downward slope and applying the brake. If the machine does not stand still the brake should be adjusted. The brake is adjusted as follows: 1.
English – 23 Replacing the air filter If the engine seems to lack power or does not run smoothly this may be because the air filter is clogged. It is therefore important to replace the air filter at regular intervals (see maintenance schedule on page 17 for correct service interval).
24 – English Checking and adjustment of the cutting unit’ s ground pressure To achieve the best cutting results the cutting unit should follow the underlying surface without pressing too hard against it. The pressure is adjusted with a screw on each side of the machine.
English – 25 Checking and adjusting the cutting unit’ s parallelism To achieve good mowing results it is important that the unit is parallel with the ground. Check this as follows: 1. Place the machine on a level surface. 2. Measure the distance between the ground and the edge of the unit, at the front and back of the hood.
26 – English Cutting unit on Rider 1200 (r ear ejection) MAINTENANCE Dismantling the cutting unit The cutting unit can be released from the machine for cleaning or checking of the blades and screws. Dismantle the cutting unit as follows: 1. Dismantle the front hood as described on page 18.
English – 27 Changing the oil The oil should be changed for the first time after 8 hours of running time. Thereafter it should be changed every 50 hours of running time. If the engine is run hard or during high temperatures the oil should be changed every 25 running hours.
28 – English Replacement of the oil filter 1. Dismantle the engine hood as described on page 18. 2. Drain of f the engine oil according to the work description “Changing of engine oil” on page 27. 3. Dismantle the oil filter . If necessary use a filter extractor .
English – 29 Checking and adjustment of the throttle wire Check that the engine responds to the throttle control and that the correct engine speed is achieved at full throttle. If necessary the following adjustment can be made: 1. Release the clamping screw and push the throttle control to full throttle position.
30 – English Checking the tyre pressure The tyre pressure should be 60 kPa (0.6 kp/cm 2 ) all round. To improve driving the pressure on the rear tyres can be reduced to 40 kPa (0.
English – 31 Problem Procedure Engine will not start. • Fuel tank empty . • Plugs defective. • Plug connections defective. • Dirt in carburettor or fuel pipe. Starter does not pull round engine. • Battery flat. • Bad contact between cables and battery terminals.
32 – English Winter storage At the end of the season the machine should immediately be put in order for storage, also if it is going to stand idle for more than 30 days. Fuel which is left to stand for long periods (30 days or more) can leave tacky deposits which can block the carburettor and interfere with the engine.
English – 33 WIRING DIAGRAM 1. Brake switch, hydrostat 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relay 7.
34 – English Rider 1030 Bioclip, Rider 1200 Dimensions Rider 1030 Bioclip Rider 1200 Length 2300 mm 2300 mm Width 1120 mm 1280 mm Height 1085 mm 1085 mm Unladen weight 300 kg 300 kg Wheel base 855 mm 855 mm T rack 710 mm 710 mm T yre size 18 x 7.50 x 8 18 x 7.
English – 35.
´*2}h¶6+¨.
English – 37.
´*2}h¶6+¨.
デバイスHusqvarna 1200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 1200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 1200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 1200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 1200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 1200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 1200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 1200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 1200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
