Husqvarnaメーカー141の使用説明書/サービス説明書
ページ先へ移動 of 18
Husqvarna Operator's Manual _ 136 / 141 Instruction Manual Read and follow all Safety Rules and Operating Instructionsbefore usingthis product. Failureto do so can result in serious injury.
1 2 3 _23 24 21 9 10 1. Cylinder Cover 2. Front Handle 3. Front Hand Guard 4. Starter Cover 5. Chain Oil Tank 6. Starter Handle 7. CarburetorAdjusting Screw 8. Choke Control 9. Rear Handle 10. ON/OFF Stop Switch 11. Fuel Tank 13. Bar Tip Sprocket 14. Saw Chain 15.
_WARNING: Always disconnect spark plug wire and place wire where it can- not contact spark plug to prevent accidental starting when setting up, transporting, ad- justing or making repairs except carburetor adjustments.
Thereshould be no smoking, openflames, or work that could cause sparks. AIIowen- gine to coolbefore refueling. • Mix and pourfuel in an outdoor areaon bare ground; store fuel in a cool,dry, well ventilated place;and use an approved, marked container for all fuel purposes.
I t Elbow locked Thumb on undersideof handlebar • Keep a good, firm grip on the saw with both hands when the engine is running and don't let go. A firm grip will help you reduce kickback and maintain control of the saw. Keep the fingers of your left hand encir- cling and your left thumb under the front handlebar.
• Tip contact in some cases may cause a lightning fast reverse REACTION, kicking the guide bar u p and back toward the oper- ator. • Pinching the saw chain along the top ofthe guide bar may push the guide bar rapidly back toward the operator.
Location of shipping spacer .,_tters Dep i Gauge Bar Clamp/ /_ Cha_ t0 0 Bar Clamp Nuts Drive Links Bar Tool • An adjusting pin and screw is used to ad- just the tension of the chain. It is very im- portant when assembling the bar, that the pin located on the adjusting screw aligns intoa hole in the bar.
• if chain is too loose, turn adjusting screw 1/4 turn clockwise. .,J-_,_ii_oi Adjusting / ,/ Chain Brake Nuts Guide Bar Adjusting Screw - 1/4 Turn • Lift up the tip of the bar and tighten the chain brake nuts with the bar tool. • Recheck chain tension.
For cold weather starting, start the unit at full choke; allow the engine to warm up before squeezing the throttle trigger. NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.
wrist against the hand guard without releas- ingyour griparound the front handle. The chain should stop immediately. Inertia activating function control _k, WARNING: When performing the fol- lowing procedure, the engine must be turned off. The chain brake must be checked several times daily.
Final (felling) cut here. 2" (5 cm) above center of_otch. First cut ,5 c_ _ / --, :÷1 / -- x!". /I Seco_6 cut_ __Notch : .... _ 5 cm • After removing the cutout of wood, make the felling cut on the opposite side of the notch. This is done by making a cut about two inches higher than the center of the notch.
BUCKING WITHOUT A SUPPORT • Overcut through 1/3 of the diameter of the log. • Roll the log over and finish with a second overcut. • Watch for logs with a compression side to prevent the saw from pinching. See il- lustration for cutting logs with a compres- sion side.
_',WARNIN_: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so. d}JLWARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.
CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpeningto a professional chain sharpener. IGNITION TIMING Ignition timing is fixed and nonadjustable. SPARK PLUG The spark plug should be replaced each year to ensure the engine starts easier and runs better.
SECTION 1 : LIMITED WARRANTY Husqvama Forest & Garden Company ("Husqvarna") warrants Husqvama product to the original purchaser to be free from defects in material and workmanship from t.
DEFINED IN THE LIMITED WARRANTY STATEMENT HUSQVARNA RESERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITH- OUT NOTICE, AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PRODUCTS.
purchase. WHAT IS COVERED: REPAIR OR REPLACEMENTOF PARTS. Repairor replacement of any warranted part will be performed at no charge to the owner at an approved HUSQVARNA servicing center.
Husqvama Printed in U.S.A..
デバイスHusqvarna 141の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 141をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 141の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 141の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 141で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 141を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 141の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 141に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 141デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。