Husqvarnaメーカー142 RB, 152RBの使用説明書/サービス説明書
ページ先へ移動 of 29
101 90 47-26 142RB/152RB Operator's Manual Read through the Operator‘s Manual carefully and understand the content before using the machine..
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine.
English – 3 List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment .
4 – English The machine ‘ s safety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (S ee the chapter “What is what“ to locate where this equipment is positioned on your machine.
English – 5 6. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . . In countries that have a warm and dry climate the risk of fire is obvious. W e have therefor e fitted certain mufflers with a spark arr estor screen.
6 – English 3. Cutting attachment guard • Check that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" .
English – 7 SAFETY INSTR UCTIONS 6. Cutting equipment This section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Reduce the machine ‘ s tendency to kickback • Obtain maximum cutting capacity.
8 – English SAFETY INSTR UCTIONS Cutting equipment IMPORT ANT INFORMA TION The section describes how through correct maintenance and through using the right type of cutting equipment you can reduce the machine ‘ s tendency to kickback, obtain maximum clearing capacity and increase the service life of the cutting equipment.
English – 9 SAFETY INSTR UCTIONS General safety instructions IMPORT ANT INFORMA TION • The machine is only designed for trimming grass and brush cutting. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “ T echnical data “ .
10 – English General working instructions SAFETY INSTR UCTIONS Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine.
English – 11 SAFETY INSTR UCTIONS Basic clearing techniques • Always carry out clearing and trimming at full throttle. • Always drop to idling speed after each working operation.
12 – English SAFETY INSTR UCTIONS Grass trimming using the trimmer head • Hold the trimmer head just above the ground at an angle. It is the end of the cord that carries out the work. Let the cord work at its own pace. Do not press the cord into the area to be cut.
English – 13 WHA T IS WHA T? What is what on the grass trimmer and the brushcutter? 1. Blade 2. G rease filler cap 3. Angle gear 4. Blade guar d 5. Shaft 6. Locking button for start throttle 7. Throttle 8. Stop switch 9. Throttle trigger lock 11. Cylinder co ver 12.
14 – English ASSEMBL Y Assembling the J-handle ! W ARNING Only grass blades or trimmer heads/ plastic blades may be used when the J- handle is fitted. Clearing blades must never be used with the J-handle. • Fit the handle using the 4 screws about 30 cm in front of the throttle lever on the shaft.
English – 15 Assembling other guards and cutting equipment • Fit the guard (A) to the gear housing using the support plate (M) and two screws (L). • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive ’ s holes aligns with the corresponding hole in the gear housing.
16 – English ASSEMBL Y Adjusting the harness and brush cutter Quick release On the front is an easily accessible, quick release catch: • Pull out the red strap. • The hip strap and one shoulder strap will be automatically released at the same time and the harness and the engine unit will slide to the ground.
English – 17 FUEL HANDLING Petrol NO TE! Always use an oil-mixed quality petrol (at least 90 octane). If your machine is equipped with a catalytic converter , (see “ technical data ”) an unleaded, oil mixed quality petrol should always be used. A leaded petrol will destroy the catalytic converter .
18 – English ST ART AND STOP Control before starting Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke posi- tion. AIR PUR GE: P rime with fuel by pr essing the dia- phragm repeatedly until fuel begins to run back into the tank through the transparent fuel hose.
English – 19 MAINTENANCE Carburettor Idle speed adjustment (T) • Check that the air filter is clean. When the idle speed is correct, the trimmerhead will not rotate. If adjustment is required, close (clockwise) the T-screw, with the engine running, until the trimmerhead starts to rotate (3 400 rpm).
20 – English MAINTENANCE Cooling system T o maintain as low an operating temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
English – 21 MAINTENANCE Angle gear The angle gear is filled with a sufficient quantity of grease at the factory . H owever , before using the machine you should check that the angle gear is filled to 3/4 with grease. U se H usqvarna special grease.
22 – English MAINTENANCE Maintenance schedule Below follo ws some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Clean the outside of the machine. 2. Make sure the harness is not damaged.
English – 23 T echnical data Engine C ylinder capacity , cm 3 /cu. inch C ylinder bore, mm/inch S troke length, mm/inch I dling speed, rpm Recommended max.
24 – English EU declaration of conformity (Only applies to Europe) (Directive 98/37/EC, Annex II, A) We, Husqvarna AB, S-561 82 Huskvarna, Sweden, tel.
.
´*3$h¶6W¨.
.
1999W38 ´*3$h¶6W¨.
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mower.
デバイスHusqvarna 142 RB, 152RBの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 142 RB, 152RBをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 142 RB, 152RBの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 142 RB, 152RBの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 142 RB, 152RBで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 142 RB, 152RBを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 142 RB, 152RBの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 142 RB, 152RBに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 142 RB, 152RBデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。