Husqvarnaメーカー225Bの使用説明書/サービス説明書
ページ先へ移動 of 28
225B 225B X-SERIES Operator´s manual Read the operator ’ s manual carefully and make sure that you understand the contents before using the blower .
2 – English CONTENTS Introduction ......................................... 3 Key to symbols .................................... 4 Safety instructions .............................. 5 Description .......................................... 7 Fuel handling .
English – 3 INTRODUCTION ! WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorised modifications and/or accessories can result in serious personal injury or the death of the operator or others.
4 – English KEY T O SYMBOLS Symbol Description Location Operator ’ s manual Blower Checks and/or mainten-ance shall be carried out after having switched off the engine. The stop switch must be set to the STOP position. Cleaning at regular intervals is required.
English – 5 Personal safety equipment Fuel safety ! Special safety instructions apply to the type of fuel used for the blower . These instructions are specified under ” Fuel handling ” on pages 1 1 and 12. The following instructions apply to persons operating the blower: 1.
6 – English 1. Do not allow bystanders or animals to be in the work area, i.e. 10 metres from the operator. 2. The blower may throw objects at high velocity that can ricochet and hit the operator. This may cause serious eye damage. 3. Never point the blower nozzle toward people or animals.
English – 7 DESCRIPTION The blower 1. Shoulder strap 2. Throttle trigger 3. Stop switch 4. Throttle lock 5. Shoulder strap ring 6. Anti-vibration system (inside the housing) 7. Fan housing 8. Fuel cap 9. Air filter 10. Choke 1 1. Inspection cover (225B X-SERIES ) 12.
8 – English DESCRIPTION Accessories (225B X-SERIES ) 21. V acuum device with collection components consisting of items 22 - 25 below . 22. V acuum bag tube.
English – 9 DESCRIPTION 34 2 ! The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components.
10 – English DESCRIPTION 24 15 14 7 13 12 1 1 Throttle trigger (2) The speed and the output of the engine are regul- ated by the throttle trigger . The throttle lock (4) must be pressed down before the trigger will actuate the throttle.
English – 11 DESCRIPTION 17 18 8 9 19 10 Starter device (18) and starter handle (17) The starter device is located at the top on the engine shrouding and engages in the crank shaft only when the starter handle is pulled.
12 – English Fuel mixture WARNING! Allow adequate ventilation while handling fuel. NOTE! The machine is fitted with a two-stroke engine and must always be run on a mixture of gasoline and two-stroke oil. It is important to measure the quantity of oil accurately , to ensure the correct mixture ratio.
English – 13 Olja • Olje Olie • Ö ljy ä Lit. 5 10 15 20 2%(1:50) 0,10 0,20 0,30 0,40 Bensin Bensin Benzin Bensiini ä Lit. O FUEL HANDLING Mixture • Always mix gasoline and oil in a clean container intended for fuel. • Always start by filling half the quantity of gasoline required.
14 – English ST ART AND ST OP WARNING! Never start the blower if the inspection cover is not closed, is damaged or cannot be closed. (Exception: When the vacuum tube is fitted). ! IMPORTANT! Do not pull out the starter cord completely and do not release the starter handle from the fully pulled out position.
English – 15 ST ART AND ST OP Press the machine body against the ground using your left hand (NOTE! Do not use your foot). Grip the starter handle with your right hand and slowly pull the starter cord out until you feel some resistance, (the starter hooks grip) now quickly and powerfully pull the cord.
16 – English USING THE BLOWER WARNING! When fitting the blower tube and nozzle, the engine must be switched off and the stop switch must be in the stop position. ! The blower tube and nozzle have a bayonet mount. Fit them in the following manner: 1.
English – 17 USING THE BLOWER ! WARNING! Never start the blower if the inspection cover is not closed, is damaged or cannot be closed. (Exception: When the vacuum tube is fitted). ! 21 14 WARNING! Do not operate the blower while standing on a ladder or a stand.
18 – English USING THE BLOWER 1. Open the collection bag. Insert the collection bag tube from inside the bag to fit in the vacuum inlet opening of the bag as illustrated in the adjacent figure. Close the zipper on the bag. 2. Press the collection bag tube on the blower, turn it 1/4 of a turn until a snap is heard.
English – 19 USING THE BLOWER ! WARNING! Do not operate the blower while standing on a ladder or a stand. When operating the blower , the blower and collection bag must be secured in the shoulder strap. The strap should be worn over the shoulder as shown in the adjacent figure.
20 – English MAINTENANCE The fuel quantity required in relation to the air flow , provided by the opening in the throttle, is adjusted by the L and H jets. If they are screwed clockwise, the air/fuel mixture becomes leaner (less fuel) and if they are screwed counterclockwise, the mixture becomes richer (more fuel).
English – 21 MAINTENANCE Muffler NOTE! Some mufflers are fitted with a catalytic converter . See “ T echnical data ” to see whether you clearing saw is fitted with a catalytic converter . The muffler is designed to dampen the noise level and to direct the exhaust fumes away from the user .
22 – English The air filter (A) must be cleaned regularly to remove dust and dirt. This will prevent: • Carburetor malfunctions • Starting problems • Reduced performance • Unnecessary wear o.
English – 23 MAINTENANCE 1 2+3 4 5 8 1+3 4 5 6 7 8 2 Maintenance schedule A number of general maintenance instructions are given below . If more detailed instructions are required, get in touch with your local servicing dealer . Daily maintenance 1.
24 – English MAINTENANCE Monthly maintenance 1. Flush the fuel tank with clean gasoline, which afterward should be disposed of in an environ- mentally correct manner . 2. Clean the outside of the carburetor and the space around it. Replace damaged parts.
English – 25 TECHNICAL DA T A 225B 26,9 35 28 3.000 8.200 7.400 0.9 kW/9000 rpm No W albro CD Champion RCJ 7Y 0.5 W albro/WT 0.4 5.1 89 105 2.6 4,3 Radial fan 83 (300) 600 Engine Cylinder volume, cm 3 : Cylinder bore, mm: Stroke, mm: Idling speed, rpm: Max.
26 – English ´+H"[¶5B¨ FEDERAL AND CALIFORNIA EMISSION CONTR OL W ARRANTY ST A TEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EP A (U.S. Environmental Protection Agency), CARB (California A.
English – 27.
2001W32 ´+H"[¶5B¨.
デバイスHusqvarna 225Bの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 225Bをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 225Bの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 225Bの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 225Bで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 225Bを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 225Bの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 225Bに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 225Bデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
