Husqvarnaメーカー2748 GLSの使用説明書/サービス説明書
ページ先へ移動 of 44
200 8-01 O 0 8 02 013 2748 GLS Operator's Manual Operator's Manual Ride Mo wer 960 43004600 03002.
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in structions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Always look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Stan dard wrench sizes are listed.
6 AS SEMBL Y NOTE: Y ou may now roll or drive your tractor off the skid. Follow the ap propriate instruction below to remove the tractor from the skid. WARNING: Before start ing, read, un derstand and fol low all in structions in the Op eration section of this man ual.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW Y OUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad justments. Save this manual for future reference.
9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per forming any adjustments or repairs. W e rec ommend a wide vision safety mask over spectacles or stan dard safety glasses.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po sition of the at tachment lift le ver (A) de termines the cutting height. • Put attachment lift lever in desired cutting height slot. The cutting height range is ap proximately 1" to 4".
11 OPERA TION FIG. 11 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous.
12 OPERA TION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un leaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).
13 FIG. 12 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
14 MAINTENANCE T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures.
15 MAINTENANCE FIG. 13 BA TTERY Y our tractor has a battery charging system which is suf ficient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not adjustable. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first.
18 SERVICE AND ADJUSTMENTS FIG. 17 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key .
19 SERVICE AND ADJUSTMENTS • A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring. • Repeat on opposite side of tractor . A B C D - Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D).
20 SERVICE AND ADJUSTMENTS TO LEVEL MOWER Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly . VISUAL SIDE- TO -SIDE ADJUSTMENT (See Fig.
21 SERVICE AND ADJUSTMENTS 02966 A A 02548 B B NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.
22 SERVICE AND ADJUSTMENTS TO REPL ACE MOTION DRIVE BEL T (See Fig. 30) P ark the tractor on level surface. En gage parking brake. For as sistance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual).
23 SERVICE AND ADJUSTMENTS FIG. 32 WEAK OR DEAD BA TTERY FULL Y CHARGED BA TTERY REPL ACING BA TTERY (See Fig. 33) WARNING: Do not short battery ter minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery , remove metal bracelets, wristwatch bands, rings, etc.
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
26 TROUBLESHOOTING POINTS Engine dies when 1. Reverse operation system 1. T urn ignition key to tractor is shifted (ROS) is not "ON" while ROS "ON" position. into reverse mower or other attachment See Operation section. is engaged.
27 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
28 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 101 40 71 34 With Service Minder Option 46 46 With 12V O.
29 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 Bat.
30 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 CHASSIS 14 214 130 130 37 194 194 181 181 182 68 68 189 176 176 176 175 178 165 228 228 183 194 236 235 152 150 202 203 204 210 .
31 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 CHASSIS KEY P ART NO . NO . DESCRIPTION 3 532 40 50-12 Logo Husq. 5 532 40 87-01 Dash 14 532 41 10-46 Hood 15 532 19 89-07 Lens .
32 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 DRIVE 56 171 216 143 197 196 125 226 125 125 80 125 51 52 170 175 279 176 178 174 22 23 166 276 153 233 drive-te x_K66_fender_1 .
33 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 DRIVE KEY P ART NO . NO . DESCRIPTION 1 532 41 41-45 T ransaxle, T uffT orq K66 2 532 00 70-70 Key 7 532 19 98-37 Hub Asm. Wheel 9 532 14 00-80 Bolt Hub Wheel 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
34 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26.
35 KEY P ART NO . NO . DESCRIPTION 1 532 41 64-80 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-89 Spindle Asm., LH 5 532 40 30-90 Spindle Asm.
36 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 ENGINE 1 84 84 29 SP ARK ARRESTER KIT 84 45 18 15 37 28 37 22 21 20 62 71 70 79 69 87 2 engine-te x_bs-2cyl_2 81 82 12 11 41 42 .
37 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 1 - - - - - - Engine B&S Model No.
38 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 SEA T ASSEMBL Y 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
39 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO .
40 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 MOWER DECK 47 7 54 46 32 33 31 30 1 33 52 48 43 50 97 33 49 39 185 46 46 6 21 122 114 98 31 32 25 26 24 27 194 113 17 21 49 187 .
41 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 87-00 Deck Weldment Mower 6 532 19 72-48 Cover Mandrel LH 7 532 19 91-02 Cover Mandrel RH 8 532 17 43-65 Bolt 7/16 Asm.
42 TRACTOR - MODEL NO . 2748GLS (96043004600), PRODUCT NO. 960 43 00-46 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-tex_3 91 89 87 89 87 2 532 19 52-23 Shaft Asm.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the da.
デバイスHusqvarna 2748 GLSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 2748 GLSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 2748 GLSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 2748 GLSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 2748 GLSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 2748 GLSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 2748 GLSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 2748 GLSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 2748 GLSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
