Husqvarnaメーカー326Lの使用説明書/サービス説明書
ページ先へ移動 of 36
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 326C 326L 326L X-SERIES 326LD X-SERIES Oper ator’ s manual (EP A) Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and theref ore reser ves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS P ersonal pr otective equipment GLO VES Glov es should be wor n when necessar y , e.g., when fitting cutting attachments. HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection.
English – 5 SAFETY INSTR UCTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimise vibration and mak e operation easier . Use of incorrectly wound cord or an incorrect cutting attachment increases the le vel of vibr ation.
6 – English SAFETY INSTR UCTIONS Chec king, maintaining and servicing the machine ′′ ′ ′ s safety equipment Throttle loc k • Make sure the throttle control is loc ked at the idle setting when the throttle lock is released. • Press the throttle lock and mak e sure it retur ns to its original position when you release it.
English – 7 SAFETY INSTR UCTIONS • If the muffler on y our machine is fitted with a spark arrestor mesh then it should be cleaned regularly . A block ed mesh causes the engine to ov erheat, which can lead to ser ious damage. Nev er use a muffler with a def ective spark arrestor mesh.
8 – English SAFETY INSTR UCTIONS General safety precautions Starting • The complete clutch cov er and shaft must be fitted before the machine is star ted, otherwise the clutch can come loose and cause personal injur y . • Ne ver start the machine indoors.
English – 9 SAFETY INSTR UCTIONS • The transpor t guard must alwa ys be fitted to the cutting attachment when the machine is being transpor ted or in storage. General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine .
10 – English SAFETY INSTR UCTIONS Cutting • The trimmer is ideal for cutting gr ass that is difficult to reach using a normal lawn mower . K eep the cord parallel to the ground when cutting. A void pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
English – 11 WHA T IS WHA T? What is what? 1 T r immer head 2 Grease filler cap 3 Be vel gear 4 Cutting attachment guard 5 Shaft7 6 Loop handle 7 Throttle control 8 Stop s witch 9 Throttle lock 10 .
12 – English ASSEMBL Y Fitting the loop handle (326C) • P osition the handle on the shaft. Note that the handle must be mounted below the arro w on the shaft. • Fit the screw , secur ing plate and wing nut as shown in the diagram. • Tighten the wing nut.
English – 13 ASSEMBL Y Fitting a trimmer guar d and Superauto II trimmer head (326L, 326Lx, 326LDx) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft.
14 – English FUEL HANDLING Fuel CA UTION! The machine is equipped with a two-strok e engine and must alwa ys been run using a mixture of gasoline and two-strok e engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
English – 15 FUEL HANDLING Fuelling • Clean the area around the fuel cap . Contamination in the tank can cause operating prob lems. • Ensure that the fuel is well mix ed by shaking the container bef ore filling the tank.
16 – English ST AR TING AND ST OPPING Chec k bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole .
English – 17 ST AR TING AND ST OPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Stopping Stop the engine by s witching off the ignition. Starting Hold the body of the machine on the ground using y our left hand (CA UTION! Not with your f oot!).
18 – English MAINTENANCE Carb urettor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.
English – 19 MAINTENANCE will run smoothly in ev er y position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. W ARNING! If the idle speed cannot be adjusted so that the cutting attachment stops, contact y our dealer/service workshop .
20 – English MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder .
English – 21 MAINTENANCE the e xcess bef ore fi tting the fi lter to the machine. Nev er use common engine oil. This would drain through the fi lter quite quickly and collect in the bottom. Bevel gear (326L, 326Lx, 326LDx) The be vel gear is fi lled with the right quantity of grease at the f actor y .
22 – English TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le v el is calculated as the time-weighted energy total f or noise pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max.
English – 23 TECHNICAL D A T A Appro ved accessories T ype Cutting attachment guar d, Art. no. 326C Blade shaft thread 3/8 R Plastic blades T r icut Ø 230 mm (R) 537 02 61-01 / 537 07 67-01 T r imm.
24 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine .
1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
.
1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6".
1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .
1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6".
1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6".
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
´®z+H6e¶5/¨ ´®z+H6e¶5/¨ 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 12 3 4 56 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 1 1" T rimmy VII.
.
´®z+H6e¶5/¨ 2003-09-17 ´®z+H6e¶5/¨ 1140226-95.
デバイスHusqvarna 326Lの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 326Lをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 326Lの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 326Lの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 326Lで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 326Lを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 326Lの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 326Lに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 326Lデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。