Husqvarnaメーカー580 R, 580 RS, 580 RSE, 580 RSW, 600 Cの使用説明書/サービス説明書
ページ先へ移動 of 26
580 R, 580 RS, 580 RSE, 580 RSW , 600 C Owner’ s Man ual 606 00 02 98A 11/00 Printed in USA.
2.
3 ENGLISH 1. Engine Control 2. Ignition Switch (Electric Star t Models) 3. Speed Selector (Self- propelled) 4. Primer (Briggs Engine) 5. Side Discharge Cov er 6. Side Discharge Deflector 7. Cutting Height Lev ers (2 Rear Wheel Adjusters, 2 F ront Wheel Adjusters) 8.
GB - 4 Controls and Features . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9 Operation . .
GB - 5 DISCLAIMER Husqv arna reser ves the right to discontinue, make changes to , and add improvements upon its products at any time without pub lic notice or obligation.The descriptions and specifications contained in this manual were in effect at printing.
GB - 6 SAFETY DECALS AND LOCATIONS AL W A YS replace missing or damaged Safety Decals. Refer to Figure 3 f or Safety Decal locations. 1. D ANGER T O A V OID SERIOUS INJUR Y OR DEA TH 2. D ANGER KEEP HANDS AND FEET A W A Y Do not operate mow er unless guards are in operating position or bagger is attached.
GB - 7 DO NO T pull mower bac kwards unless absolutely necessary . Look down and bac k before and while mo ving backw ards. DO NO T star t the engine or operate mow er unless either the Side Discharge Opening Cov er or the Side Discharge De fl ector is installed.
GB - 8 DO NO T make cutting height wheel adjustments while the engine is running. On self-propelled models, releasing wheel drive control must stop mo wer ’ s forward mov ement. If this feature f ails to operate, disconnect spark plug wire and repair before using unit.
GB - 9 T O REMO VE UNIT FROM CAR T ON 1. Cut off top of car ton. 2. Remov e front and rear inser ts and literature pack. 3. Cut out back of carton and roll unit out. 4. Remov e protective pac kaging materials. ASSEMBL Y 1. Unfold and adjust handlebar .
GB - 10 CONTROLS AND F EATURES See Figures 1 and 6 for Controls and Features . Engine/Blade Control The Engine Control must be held against the handlebar in order to star t the engine as well as during mowing operations to keep the engine running. Releasing the control during operation stops the engine and blade .
GB - 11 OPTIONAL CONTROLS See Figures 1 and 6. Cutting Height – Swivel Models T o change front wheel cutting height, inser t clevis pin into the holes that correspond to the desired cutting height. (Figure 6). T o change rear wheel cutting height, mov e cutting height lev ers one notch at a time until the desired cutting height is obtained.
GB - 12 FILLING FUEL T ANK T o add fuel to Fuel T ank: 1. Put unit in open or well-v entilated area. 2. Stop engine and allow to cool. 3. Clean Fuel Cap and surrounding area to prev ent dust, dir t and debr is from entering Fuel T ank. 4. Remov e Cap .
GB - 13 STARTING AND SHUT OFF See Figures 1, 4 and 6 for all Controls and Features . NO TE: Star t engine on a hard lev el surface that is free of debris. Manual Start 1. Check each item in Bef ore Each Use in the Maintenance Schedule. 2. For engines with a primer , push pr imer bulb 2 or 3 times f or a cold engine.
GB - 14 Husqv arna Dealers will provide any service, par ts or adjustments which may be required to keep y our unit operating at peak ef fi ciency . Should engine service be required, contact a Husqv arna dealer or an author ized engine manuf acturer's service center.
GB - 15 1. Loosen wing bolt and lift cov er . Remov e pre-cleaner and car tridge assembly . 2. W ash pre-cleaner in liquid detergent and water . Allow to dry thoroughly . Saturate pre-cleaner in oil (SAE #30). Squeeze to remov e excess oil. Do not wring.
GB - 16 CHECK DRIVE BELT Check drive belt f or wear or damage. Replace belt if worn or damaged. See Ser vice and Adjustments . CHECK ENGINE/BLADE CONTROL The engine/blade control must stop the engine and blade within 3 seconds after the bail is released.
GB - 17 CHECK ENGINE COOLING Engine is air cooled. Air must circulate freely around engine from Air Intake to cooling fins on cylinder head and bloc k to prev ent ov erheating. Every 100 hours of operation or yearly (more often if conditions require) remov e cooling shrouds and clean cooling fins.
GB - 18 SERVICE P OSITION Place unit on a fl at lev el surface. AL W A YS stop engine. Assure unit is secure and will not tip ov er . Strap and clamp onto bench if needed. A handlebar service position is provided for tipping the unit for cleaning and service (Figure 14).
GB - 19 3. Charge for 24 to 48 hours (battery may be charged for up to 72 hours with no harmful effects). An engine run time of at least 8 hours is required to charge a fully discharged battery . T o Remove Battery from Unit 1. Remov e wing nuts from battery U-bolt.
GB - 20 DRIVE BELT (Self propelled units) T o remov e drive belt: 1. P osition right hand rear wheel Height Adjustment lev er in fi rst notch and left hand rear wheel Height Adjustment lev er in third notch. This provides clearance between friction wheel and drive disk.
GB - 21 IMPORT ANT: NEVER spra y unit with water or store unit outdoors. W ater can seep into sealed bearings, which are sealed against dir t and debris only , causing reduced component life . Store mower in a cool, dry , protected location. Cleaning Clean unit thoroughly .
GB - 22 T ROUB LESHOOTING PROBLEM PROB ABLE CAUSE CORRECTION Engine will not start 1. Fuel tank empty or low . 2. Spark plug wire loose or off. 3. Engine/brake control cab le detached, broken, or not adjusted properly . 4. Battery discharged (electr ic star t models).
GB - 23 SPECIFICATIONS Model Number 601 10 00 24 601 10 00 20 601 10 00 21 601 10 00 22 601 10 00 23 Description 580 R 580 RS 580 RSE 580 RSW 600 C Length - in (cm) 61.5 (156) Height - in (cm) 38 (96,5) Width - in (cm) 23 (58,4) Actual Weight - lbs (kg) 81 (36,7) 97 (44,0) 102 (46,3) 105 (47,6) 118 (53.
GB - 24 W ARRANTY ST A TEMENT SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company ( “ Husqv arna ” ) warrants Husqvarna product to the original pur- chaser to be free from defects i.
GB - 25.
01194000A.
デバイスHusqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 580 R, 580 RS, 580 RSE, 580 RSW, 600 Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。