Husqvarnaメーカー80792の使用説明書/サービス説明書
ページ先へ移動 of 28
Shindaiwa T rimmer Head Guide How to load and service the most popular Shindaiwa trim- mer heads, including complete replacement parts information and other important technical data.
2 Current Models Bolt Size 22F 8mm / MRH F230 8mm / MRH 22T 7mm / MLH T230, T231, C230, T2500, 65001 7mm / MLH T250, C250 8mm / MLH T260, T261, C260 8mm / MLH T270, T271, C270, T350 8mm / MLH C350, B4.
3 The most common cause of trimmer head malfunction is poor mainte- nance, especially true for tap-for-line, bump-feed, and fully automatic heads. Customers buy these heads for convenience so they don’t have to reach down and advance the line–yet that added convenience often means the head is not properly maintained.
4 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets. 72036-15200 72005-92001 72017-92001 Shipped with 20 feet of .080 line. Maximum fill– 40 feet of .
5 7 8 9 10 11 12 Low Profile Head *2 required PA RTS LIST 1 Adapter Bolt 2 Outer Housing To advance line: With the engine off, loosen the bottom knob a few turns in the direction of rotation. Grasp the trimmer head in both hands. Rotate the bottom of the spool clockwise and pull the line through the eyelets.
6 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets.
7 7 8 9 SemiMatic P ARTS LIST 1 Adapter Bolt 2 Outer Housing 3 Spring 4 W asher 5 Cam Assembly 6 Cam Lock 7 Inner Spool 99909-15500 Item Part No. 1 72036-15210 2 99909-15510 3 99909-15520 4 99909-15530 5 99909-15540 6 99909-15550 7 99909-15560 99909-15600 Item Part No.
8 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets. INST ALLA TION INSTRUCTIONS E-Z Load and E-Z Pro T rimmer Heads 1 2 3 4 5 6 E-Z Load E-Z Pro Line Chart Press the upper body in at the spots marked “Push Open”.
9 Check for a maximum line overlap of one to two inches (four to five inches of line extending from each eyelet). T rim as required to final length. 7 8 9 10 11 12 E-Z Load *2 required PA RTS LIST 1 O.
10 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets.
11 7 8 9 10 11 12 High Capacity *2 required PA RTS LIST 1 Adapter Bolt 2 Outer Housing 3 Eyelets 4 Inner Spool 5 Retaining Ring 6 Outer Cover 7 Spring Replace the cover . T ighten the lower knob by turning counterclockwise. Pull the line ends free from the line saver slots.
12 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets.
13 7 8 9 10 11 12 PA RTS LIST To advance line: With the engine off, loosen the wing nut a few turns in the direction of rotation. Grasp the trimmer head with both hands. Rotate the bottom of the spool clockwise and pull the line through the eyelets. Re-tighten the wing nut before operating the trimmer .
14 NOTE: Operating with trimmer line of uneven length will cause excessive vibration. Always make sure the line is wound evenly and trimmed to equal lengths from the eyelets. UN34-8R Shipped with 21 feet of .080 line. Maximum fill– 33 feet of .080 16 feet of .
15 Lock the ends of line into line saver slots in spool. Insert the spring onto the bolt. With the line saver slots on the spool facing the bolt, thread the ends of the line into the eyelets in the housing. Do not allow the line to go under the spool.
16.
17.
18.
19.
20 UN10 Assembly and Rewinding Instructions A B C A . 7mm LH (gold p/n 80676) (Fits 22T, 22C, T230, T231, C230, T2500, T2500X, 65001 multipurpose tool) B . 8mm LH (silver p/n 80677) (Fits T260, T261, C260, T270, T272X, C270, T350) C . 10mm LH (silver p/n 80678) (Fits C350, B450, B530) NOTE: Each package contains (3) steel studs.
21 UN30 Assembly and Rewinding Instructions A B C A . 7mm LH (gold p/n 80676) (Fits 22T, 22C, T230, T231, C230, T2500, T2500X, 65001 multipurpose tool) B . 8mm LH (silver p/n 80677) (Fits T260, T261, C260, T270, T272X, C270, T350) C . 10mm LH (silver p/n 80678) (Fits C350, B450, B530) NOTE: Each package contains (3) steel studs.
22 UN32 Assembly and Rewinding Instructions A B C A . 7mm LH (gold p/n 80676) (Fits 22T, 22C, T230, T231, C230, T2500, T2500X, 65001 multipurpose tool) B . 8mm LH (silver p/n 80677) (Fits T260, T261, C260, T270, T272X, C270, T350) C . 10mm LH (silver p/n 80678) (Fits C350, B450, B530) NOTE: Each package contains (3) steel studs.
23 INST ALLA TION INSTRUCTIONS Flail T rimmer Heads If the machine is equipped with a trimmer line head (T18/T230 models), unscrew the head (turn clockwise to remove) and remove all adapters. Replace the spacer and install all parts as shown above. T ighten the arbor bolt securely .
24 Model View 1 2 INST ALLA TION INSTRUCTIONS Super Flail T rimmer Heads The three-blade super flail head is a perfect attachment for trimming grass, vegetation, and light brush. The nylon blades are supported by a metal bearing surface for superior perfor- mance and durability .
25 INST ALLA TION INSTRUCTIONS Fixed Line T rimmer Heads T18, T230/C230 Item Part No. Spacer 22035-13230 Holder A 22035-13242 Bolt Guard 22035-13290 Arbor Bolt 22035-13271 T250/C250, T260/C260 Item Part No. Holder A 22024-13912 Bolt Guard 22024-13291 Arbor Bolt 22000-13512 T270/C270 Item Part No.
26 INST ALLA TION INSTRUCTIONS Shindaiwa Heavy-duty Fixed-line Head The Shindaiwa Heavy-duty Fixed-line Head package* (p/n 80410) comes complete with the necessary hardware to fit all Shin- daiwa straight shaft grass trimmers and brushcutters. *Package containing Fixed-line Trimmer Head, (2) arbor bolts and spacer washer.
27 How to Fit a Shindaiwa T rimmer Head Onto Other Brand Grass T rimmers. Shindaiwa offers adapter kits that let you install Shindaiwa trimmer heads onto virtually every grass trimmer model on the market. Find your machine on the following chart to identify the kit you need.
28 Shindaiwa Inc. 1 1975 SW Herman Road T ualatin, OR 97062 Phone 503 692-3070 FA X 503 692-6696 www .shindaiwa.com Printed in U.S.A. Item 80792 6/03 Specifications subject to change without notice.
デバイスHusqvarna 80792の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 80792をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 80792の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 80792の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 80792で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 80792を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 80792の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 80792に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 80792デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
