Husqvarnaメーカー917.2896の使用説明書/サービス説明書
ページ先へ移動 of 52
Owner's Manual 532 43 62-86 917.289600 (L TH18538).
2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine.
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off.
4 PRODUCT SPECIFICA TIONS CONGRA TUL A TIONS on your purchase of a new tractor . It has been designed, engineered and manu fac tured to give you the best possible dependability and performance. Should you experience any problem you cannot easily rem- edy , please contact your nearest authorized service center/ department.
5 Steering Wheel Steering Wheel Seat (1) Seat Steering Boot Steering Extension Shaft Steering Wheel Adapter Key(s) Slope Sheet (1) Oil Drain T ube F or F uture Use (1) Hex Bolt (1) Lock W asher (1) La.
6 Fig. 2 Fig. 1 L ABEL TO REMOVE TRACTOR FROM CARTON UNP ACK CARTON • Remove all accessible loose parts and parts cartons from carton . • Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. • Check for any additional loose parts or cartons and remove.
7 AS SEMBL Y INST ALL SEA T (See Figs. 3 and 4) • Remove bolt and flat washer se cur ing seat to cardboard packing and set aside for as sem bly of seat to tractor . Remove the cardboard packing and discard. • Connect switch to seat. • Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.
8 AS SEMBL Y ✓ CHECKLIST BEFORE YOU OPERA TE YOUR NEW TRAC TOR, WE WISH TO ASSURE THA T YOU RECEIVE THE BEST PERFORMANCE AND SA TISF ACTION FROM THIS QUALITY PRODUCT . PLEASE REVIEW THE FOLL OWING CHECKLIST : ✓ All assembly instructions have been com plet ed.
9 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA.
10 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
11 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. W e rec om mend a wide vision safety mask over spectacles or stan dard safety glasses.
12 Fig. 11 Fig. 12 TO TRANSPORT (See Figs. 14) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po si tion. F ree wheel control is located at the rear of tractor . • Raise attachment lift to highest position with at tach ment lift control.
13 Fig. 15 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERA TING) 0 2 8 2 8 TO OPERA TE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills.
14 • Insert key into ignition and turn key clockwise to “ST ART” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen sec onds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again.
15 MAINTENANCE T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil.
16 TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
17 TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. T o prevent pos - si ble damage to seals, do not use high pressure water or steam to clean transmission.
18 00667 FUEL FIL TER CL AMP CL AMP IN-LINE FUEL FIL TER (See Fig. 21) The fuel filter should be replaced once each season. If fuel filter becomes clogged, ob struct ing fuel flow to car bu re tor , re place ment is re quired. • With engine cool, remove filter and plug fuel line sec tions.
19 WARNING: TO A VOID SE RI OUS IN JU RY , BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position.
20 SERVICE AND ADJUSTMENTS E F C G Q R D K G P B L M A E F H J M Fig. 26 Fig. 27 A B D C Fig. 24 Fig. 25 Fig. 28 IMPORT ANT : CHECK BEL T FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.
21 SERVICE AND ADJUSTMENTS • If adjustment is necessary , see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT -TO-BACK ADJUSTMENT (See Fig. 31 & 32) IMPORT ANT : Deck must be level side-to-side.
22 Fig. 34 TO REPL ACE MOWER BL ADE DRIVE BEL T (See Fig. 33) The mower blade drive belt may be replaced without tools. P ark the tractor on level surface. Engage parking brake. BEL T REMOV AL - • Remove mower from tractor (See “TO REMOVE MOW ER” in this section of manual).
23 TO REMOVE WHEEL (See Fig. 36) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle.
24 Fig. 38 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
25 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
26 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
27 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. F aulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
28 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
29 TRACTOR - - MODEL NUMBER L TH18538 (289600) SCHEMA TIC M FUSE ST ARTER SOLENOID BA TTERY CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) SEA T SWITCH (NOT OCCUPIED) SHORTING CONNECTOR CHASS.
30 TRACTOR - - MODEL NUMBER L TH18538 (289600) ELECTRICAL 30 33 34 22 79 21 41 42 26 43 27 40 71 16 87 25 T02S 90 28 55 With 12V Outlet Option 59 103 With Service Minder Option 46 46 94 92 29 93 2.
31 TRACTOR - - MODEL NUMBER L TH18538 (289600) ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 19 32-28 Box Battery 16 532 17 61-38 Sw.
32 TRACTOR - - MODEL NUMBER L TH18538 (289600) CHASSIS 68 68 68 68 183 183 236 236 34 235 235 137 177 175 130 151 234 214 234 205 202 25 203 206 14 191 297 204 15 130 130 18 176 176 182 130 150 176 17.
33 3 532 40 50-12 Logo 5 532 40 75-92 Dash 14 532 41 10-73 Hood 15 532 41 10-79 Lens LH 18 532 42 69-63 Grille 25 532 41 10-78 Lens RH 34 532 19 61-25 Plate Engine 36 817 06 05-12 Screw 5/16-18 x 3/4 .
34 TRACTOR - - MODEL NUMBER L TH18538 (289600) DRIVE 56 185 51 231 170 64 161 184 42 216 143 125 226 227 125 80 125 221 211 175 279 176 178 174 22 23 166 232 153 233 166 159 15 35 167 160 188 186 189 .
35 TRACTOR - - MODEL NUMBER L TH18538 (289600) DRIVE KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - - - T ransaxle, T ufftorq K46BA (Internal P arts Not Available) 2 532 12 35-83 Key Square 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
36 TRACTOR - - MODEL NUMBER L TH18538 (289600) ENGINE 21 20 OPTIONAL EQUIPMENT Spark Arrester 29 18 15 37 28 engine-te x_BS_36 12 42 85 9 90 84 45 1 122 69 2 79 97 96 37.
37 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 1 - - - - - - Engine Briggs Model No.
38 TRACTOR - - MODEL NUMBER L TH18538 (289600) STEERING ASSEMBL Y 61 steering-tex_STDHRR_5_r1 19 60 59 58 5 62 15 14 13 13 53 8 70 68 69 16 28 28 13 22 64 4 15 14 35 6 9 8 7 9 8 7 67 67 66 6 2 63 57 6.
39 KEY P ART NO . NO . DESCRIPTION 1 532 42 34-69 Wheel, Steering 2 532 19 59-68 Axle Asm., F ront 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm., RH 6 532 12 49-31 Bearing, Race Thrust Harden 7 532 12 17-48 W asher 25/32 x 1-5/8 x 16 Ga.
40 TRACTOR - - MODEL NUMBER L TH18538 (289600) MOWER DECK 1 144 145 40 19 19 6 6 30 38 189 34 189 188 21 69 21 21 30 38 30 188 43 42 60 63 46 147 55 64 34 56 57 59 40 145 57 209 56 38-8_T ex-L T_5 32 .
41 TRACTOR - - MODEL NUMBER L TH18538 (289600) MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 14-83 Mower Housing 6 532 19 51-86 Arm Suspension 7 532 41 63-58 Screw #10 x 0.
42 TRACTOR - - MODEL NUMBER L TH18538 (289600) MOWER LIFT 2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-31 Lever Asm., Lift RH 7 532 41 15-55 Grip, Lever 10 532 19 63-14 Spring T orsion 87 532 19 42-09 .
43 TRACTOR - - MODEL NUMBER L TH18538 (289600) SEA T ASSEMBL Y 1 532 42 40-67 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
44 MODEL K46BA 7A646084100 33 16 20 10 34 34 35 19 13 90 95 34 76 80 81 84 87 86 8 9 15 7 82 78 82 85 83 ACTUAL P AR TS MA Y NOT APPEAR AS SHOWN 97 103 107 108 101 102 102 109 91 106 58 105 96 72 72 TRACTOR - - MODEL NUMBER L TH18538 (289600) TUFF TORQ TRANSAXLE MODEL NO .
45 TRACTOR - - MODEL NUMBER L TH18538 (289600) TUFF TORQ TRANSAXLE MODEL NO . K46BA KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.
46 TRACTOR - - MODEL NUMBER L TH18538 (289600) BRIGGS ENGINE - MODEL NUMBER 31N707, TYPE NUMBER 1374-B1 %.
47 TRACTOR - - MODEL NUMBER L TH18538 (289600) BRIGGS ENGINE - MODEL NUMBER 31N707, TYPE NUMBER 1374-B1 ! .
48 TRACTOR - - MODEL NUMBER L TH18538 (289600) BRIGGS ENGINE - MODEL NUMBER 31N707, TYPE NUMBER 1374-B1 1 796010 Cylinder Assembly 2 399265 Bushing/SealKit (Magneto Side) 3 • 391086s Seal-Oil (Magne.
49 TRACTOR - - MODEL NUMBER L TH18538 (289600) BRIGGS ENGINE - MODEL NUMBER 31N707, TYPE NUMBER 1374-B1 562 691 1 19 Screw (Governor Control Lever) 579 691029 Nut (Starter Cable) 584 794682 Cover-Brea.
50 SERVICE NOTES.
51 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e .
05.04.10 JA Printed in the U.S.A..
デバイスHusqvarna 917.2896の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 917.2896をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 917.2896の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 917.2896の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 917.2896で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 917.2896を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 917.2896の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 917.2896に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 917.2896デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
