Husqvarnaメーカー966765403の使用説明書/サービス説明書
ページ先へ移動 of 32
E E E E n n n n g g g g l l l l i i i i s s s s h h h h 323L 325C X-SERIES Oper ator’ s manual (EP A I and II) Please read the operator’ s man ual carefully and mak e sure you understand the instructions before using the machine.
2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Please read the operator’ s manual carefully . Long-term exposure to noise can result in permanent hear ing impairment.
4 – English INTR ODUCTION Dear customer! Congratulations on y our choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , for production of m uskets .
English – 5 WHA T IS WHA T? What is what? 1 T r immer head 2 Grease fi ller cap , be vel gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop s witch 9 Thro.
6 – English GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HEARING PRO TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If you use a visor then you m ust also wear approv ed protective goggles.
English – 7 GENERAL SAFETY PRECA UTIONS Throttle loc k The throttle lock is designed to pre vent accidental operation of the throttle control. When you press the loc k (A) (i.
8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Y our machine is equipped with a vibration damping system that is designed to reduce vibration and mak e operation easier . Use of incorrectly wound cord or an incorrect cutting attachment increases the le vel of vibr ation.
English – 9 GENERAL SAFETY PRECA UTIONS Locking n ut A locking n ut is used to secure some types of cutting attachment. When fi tting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. T o remov e it, undo the nut in the same direction as the cutting attachment rotates.
10 – English ASSEMBL Y Fitting the loop handle (325Cx) • P osition the handle on the shaft. Note that the handle must be mounted below the arro w on the shaft. • Fit the screw , secur ing plate and wing nut as shown in the diagram. • Tighten the wing nut.
English – 11 ASSEMBL Y Fitting other guar ds and cutting attachments (323L) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fi tting on the shaft and secure with the bolt (L). • Fit the drive disc (B) on the output shaft.
12 – English FUEL HANDLING Fuel safety Ne ver start the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vapor ate. 2 If you ha ve spilt fuel on yourself or y our clothes, change your clothes . W ash any par t of your body that has come in contact with fuel.
English – 13 FUEL HANDLING Mixing • Alwa ys mix the gasoline and oil in a clean container intended f or fuel. • Alwa ys star t by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.
14 – English ST AR TING AND ST OPPING Chec k bef ore star ting • Ne ver start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Obser ve y our surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment.
English – 15 ST AR TING AND ST OPPING Star ting and stopping Starting Primer bulb: Press the primer bulb repeatedly until fuel begins to fi ll the bulb . The bulb need not be completely fi lled. Choke: Set the choke control in the chok e position.
16 – English W ORKING TECHNIQUES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine .
English – 17 W ORKING TECHNIQUES Clearing • The clearing technique removes all unw anted vegetation. K eep the tr immer head just abov e the ground and tilt it. Let the end of the cord strike the ground around trees , posts, statues and the like .
18 – English MAINTENANCE Carb uretor Y our Husqv arna product has been designed and manuf actured to speci fi cations that reduce har mful emissions.
English – 19 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.
20 – English MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder .
English – 21 MAINTENANCE Bevel gear (323L) The be vel gear is fi lled with the right quantity of grease at the f actor y . Howe ver , before using the machine y ou should check that the be vel gear is fi lled three-quarters full with grease. Use HUSQV ARNA special grease.
22 – English MAINTENANCE Maintenance schedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are described in the Maintenance section. Maintenance Daily maintenance W eekly maintenance Monthly maintenance Clean the outside of the machine.
English – 23 TECHNICAL D A T A T echnical data Note 1: Equivalent noise pressure le v el is calculated as the time-weighted energy total f or noise pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idle and 1/2 max.
24 – English TECHNICAL D A T A 323L Appro ved accessories T ype Cutting attachment guar d, Art. no. Arbor shaft thread M10 Plastic blades T r icut Ø 300 mm 503 93 42-02 Grass b lade/grass cutter Gr.
English – 25 FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na Forest & Garden are pleased to e xplain the emissions control system warranty on your 2001 and later small nonroad engine .
1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm.
.
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35.
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5.
´®z+H?e¶5¨ ´®z+H?e¶5¨ T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm.
6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 12 3 4 56 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 1 1" T rimmy VII.
´®z+H?e¶5¨ 2005-03-07 ´®z+H?e¶5¨ 1140316-95.
デバイスHusqvarna 966765403の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna 966765403をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 966765403の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 966765403の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 966765403で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 966765403を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 966765403の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 966765403に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 966765403デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
