Husqvarnaメーカー966957301の使用説明書/サービス説明書
ページ先へ移動 of 20
505 29 00-57 04.21.08 CL PRINTED IN U.S.A. OWNER/OPERA TOR MANU AL Model: CT20 / 966957301 SPECIFICA TIONS • Durable T ecumseh TC III Engine • P ositive On/Off Switch • Heavy-Duty Handlebars wit.
2 SAFETY RULES AND PRECAUTIONS As with any item of power equipment it is necessary that you learn and observe ALL safety precautions. This includes the care for the machine as well as personal safety . This machine is only as dangerous as the person who is operating it.
3 9. Before cleaning, repairing, or inspecting, STOP THE ENGINE, make certain all moving parts have stopped, and disconnect the spark plug wire. 10. NEVER run engine indoors. Exhaust fumes contain Carbon Monoxide which is an ODORLESS and DEADL Y POISONOUS GAS.
4 T ABLE OF CONTENTS DESCRIPTION P AGE Safety Rules and Precautions.......................................................................................................2-3 Assembly ....................................................................
5 AS SEMBL Y With the exception of handlebars, controls and transport kit, your new tiller has been completely assembled at the factory . It should be noted that right and left sides are determined by the operators position behind the unit. HANDLEBARS (L OWER) (See Fig.
6 THROTTLE CABLE Unwind throttle cable from around engine. CAUTION: Be careful not to kink cable. ON/OFF SWITCH 1. Place 1 3/8” long slotted pan head screw into switch plate and down through hole in upper right hand handlebar . (See Fig. 2) 2. Place rubber isolator over screw underneath handlebar .
7 WARNING-24:1- Disregard instructions on oil containers. Do not mix directly in fuel tank. Do not use multi-viscosity oils. Use high speed air cooled 2-cycle oil . U.S Imperial Metric Gas Oil Gal. Oz. Gas Oil Gal. Oz. Gas Oil Gal. Oz. 1 5 2 10 1 6 2 12 4 166 8 322 T o start engine, place the unit in a flat, clear area.
8 WARNING: When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury . T o avoid this risk, carefully follow these instructions: Move rocker switch to "I" position. 5. Grasp starter cord handle. Se Fig.
9 TINE SP ACERS The two tine spacers provided can be used to replace outside tines to narrow tilled path. DANGER! AL WA YS MOVE SWITCH TO "O" POSITION AND REMOVE SP ARK PLUG WIRE BEFORE TRYING TO REMOVE OBSTRUCTIONS. CLEAN UNIT AFTER EACH OPERA TION.
10 TO CLEAN SCREEN a) Wash SCREEN in water and detergent solution. b) Rinse thoroughly in clean water , then air dry . TO CLEAN AND RE-OIL FOAM FIL TER a) Wash FOAM FIL TER in water and detergent solution and squeeze (don’t twist) until all dirt is removed.
11 4).% (5" ./4%ª(5" 0/3)4)/.ª). 2%, ! 4)/.3()0 4/ª4).%3 &2/.4 /&ª4),,%2 34/.9ª3/),ª0 ! 44%2.ªA 34/.9ª3/),ª0 ! 44%2.ªB &2/.4 /&ª4),,%2 &2/.4 /&ª4),,%2 2%'5, !2ª4).%ª0 ! 44%2. ª ª ª 4.
12 IDLE SCREW NARROW CUL TIVA TING The two outer tines can be removed to give you a narrower cultivating width. This width is approximately 6". This will give you the ability to get between very closely spaced plants. In order to do this, pull the hairpin out of the hole in the outboard end of the tine shaft.
13 HANDLEBARS/GRIP/ON-OFF SWITCH/ THROTTLE CONTROL/THROTTLE CABLE ITEM ORDER NO . NO. DESCRIPTION QTY . REQ. 1 505 29 00-01 Grip, Handlebar 2 2 505 29 00-02 Screw , #10-24 x 1 3/8 1 3 505 29 00-03 Swi.
14 TRANSMIS SION ASSEMBL Y ITEM ORDER NO . NO. DESCRIPTION QTY . REQ . 1 505 29 00-18 Seal 2 2 505 29 00-19 Screw , Phillips Pan Hd 1/4-20 x 1/2 2 4 505 29 00-20 Bushing, Bronze 2 5 505 29 00-21 Drum .
15 ENGINE/TRANSMIS SION/TINES/SHIELD ITEM ORDER NO . NO . DESCRIPTION QTY . REQ. 1 – – – – – – – Engine* 1 2 505 29 00-61 Clutch Assy 1 3 505 29 00-62 Spring, Clutch 2 4 505 29 00-39 Dra.
16 TRANSPORT KIT AS SEMBL Y 1. Assemble the wheel assembly and install the wheel assembly on the tiller with the arrow up as shown. T orque: 14 ft-lb (20 N-m).
17 NOTES.
18 NOTES.
19 NOTES.
SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the d.
デバイスHusqvarna 966957301の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna 966957301をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna 966957301の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna 966957301の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna 966957301で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna 966957301を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna 966957301の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna 966957301に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna 966957301デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。