HusqvarnaメーカーCRT1350LSの使用説明書/サービス説明書
ページ先へ移動 of 28
CRT1350LS Owner's Manual / 96093001600 / 2009-12 532 43 23-74.
2 • Keep children and pets away . • Do not overload the machine capacity by attempting to till too deep at too fast a rate. • Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing. • Never allow bystanders near the unit.
3 CONGRA TUL A TIONS on your purchase of a new tiller . It has been designed, en gi neered and manu fac tured to give you the best pos sible de penda bil ity and per form ance. Should you experience any prob lems you can not easily remedy , please contact your nearest authorized service center .
4 TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier . Standard wrench sizes are listed. (1) Utility knife (1) Tire pressure gauge (1) P air of pliers (1) 9/16" wrench OPERA TOR’S POSITION (See Fig.
5 AS SEMBL Y • Grasp handle assembly . Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. Fig. 4 UNP ACKING CARTON (See Fig. 2) CAUTION: Be careful of exposed sta ples when handling or disposing of cartoning material.
6 AS SEMBL Y SHIFT ROD HAIRPIN CLIP SHIFT LEVER INDICA TOR REMOVE TILLER FROM CRA TE • Make sure shift lever indicator is in “N” position (See Fig. 7) • Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton.
7 KNOW Y OUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
8 TURNING • Release the drive control bar . • Move throttle control to “SL OW” position. • Place shift lever indicator in “F ” (forward) position. Tines will not turn. • Lift handle to raise tines out of ground. • Swing the handle in the opposite direction you wish to turn, being careful to keep feet and legs away from tines.
9 • When you have completed your turn-around, release the drive control bar and lower handle. Place shift lever in till position and move throttle control to de sired speed. T o begin tilling, hold drive control bar against the handle. TO TRANSPORT CAUTION: Before lifting or trans port- ing, allow tiller engine and muffler to cool.
10 OPERA TION • Soil conditions are important for proper tilling. Tines will not readily penetrate dry , hard soil which may con trib ute to excessive bounce and difficult handling of your tiller . Hard soil should be mois tened before tilling; however , extremely wet soil will “ball-up” or clump during tilling.
11 MAINTENANCE GENERAL RECOMMENDA TIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. T o receive full value from the warranty , the operator must main tain tiller as instructed in this manual.
12 MAINTENANCE Fig. 16 OIL FILLER PLUG OIL LEVEL OIL DRAIN PLUG Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to prevent accidental start ing of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel.
13 Fig. 18 COOLING SYSTEM (See Fig. 19) Y our engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff -bristled brush. • Keep cylinder fins, levers, and linkage free of dirt and chaff.
14 SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT (See Fig. 20) Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.
15 SERVICE AND ADJUSTMENTS CABLE CLIP SCREW DRIVE CONTROL CABLE ENGINE PULLEY IDLER PULLEY TRANS MIS SION PULLEY TO REPL ACE GROUND DRIVE BEL T (See Fig. 23) • Remove belt guard (See “TO REMOVE BEL T GUARD” in this section of this manual). • Remove old belt by slipping off engine pulley first then remove from transmission pulley .
16 SERVICE AND ADJUSTMENTS Fig. 25 • T o maintain the superb tilling performance of this ma- chine the tines should be checked for sharpness, wear , and bending, particularly the tines which are next to the transmission. If the gap between the tines ex ceeds 3-1/2 inches they should be replaced or straight ened as necessary .
17 SERVICE AND ADJUSTMENTS ENGINE TO AD JUST CARBURETOR The carburetor has been preset at the factory and ad just ment should not be necessary . However , engine per for mance can be affected by dif fer enc es in fuel, tem per a ture, al ti tude or load.
18 Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure.
19 Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Dirty air cleaner . 4. Clean or replace air cleaner cartridge.
20 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 HANDLE ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 21 532 18 11-27 Handle 23 532 08 67-77 Screw , Hex W asher SL T #10-24 x .
21 1 3 3 7 62 3 2 15 15 15 54 24 28 3 64 15 15 25 6 3 4 26 17 19 16 27 2 3 17 14 18 18 18 3 2 3 0 3 9 6 5 8 12 42 7 9 10 29 m ai n fra m e_left_19 . euro REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 MAINFRAME, LEFT SIDE KEY P ART NO .
22 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 MAINFRAME, RIGHT SIDE 15 - - - - - - - Engine, Briggs Model No.
23 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 TRANSMISSION KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 28 532 00 83-57 Gear , Reverse Idler 29 532 14 45-62 Gear , Assembly , Reverse Idler (Includes Key Nos.
24 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 TINE SHIELD .
25 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 TINE ASSEMBL Y KEY P ART NO . NO. DESCRIPTION 1 532 00 65-56 Tine, Outer , L.
26 REP AIR P ARTS TILLER - - MODEL NO . CRT1350LS (96093001600), PRODUCT NO . 960 93 00-16 DECALS 1 532 43 24-75 Decal, Logo 2 532 42 20-12 Decal, Logo 3 532 43 31-95 Decal, Tine Shield 4 532 43 14-63.
27 SERVICE NOTES.
12.10.09 AP/SR Printed in the U.S.A..
デバイスHusqvarna CRT1350LSの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna CRT1350LSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna CRT1350LSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna CRT1350LSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna CRT1350LSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna CRT1350LSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna CRT1350LSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna CRT1350LSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna CRT1350LSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。