HusqvarnaメーカーCS 2159Cの使用説明書/サービス説明書
ページ先へ移動 of 44
English CS 2156, CS 2156C CS 2156CWH CS 2159, CS 2159W CS 2159WH CS 2159C CS 2159CWH Operator ′ s manual Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
KEY T O SYMBOLS 2 – English Symbols on the machine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
CONTENTS English – 3 Contents KEY T O SYMBOLS Symbols on the machine: ..................................... 2 Symbols in the operator’ s manual: ....................... 2 CONTENTS Contents ..........................................................
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Jonsered product! We are con vinced that you will appreciate with great satisf action the quality and perf or mance of our product f or a very long time to come .
English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Cylinder cov er 2 F ront handle 3 Chain brake and front hand guard 4 Star ter 5 Chain oil tank 6 Star ter handle 7 Adjuster screws carb urettor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop switch (Ignition on/off s witch.
GENERAL SAFETY PRECA UTIONS 6 – English Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw .
GENERAL SAFETY PRECA UTIONS English – 7 pro vide information about which training materials and courses are a v ailable. Work is constantly in progress to impro ve the design and technology - impro v ements that increase your saf ety and efficiency .
GENERAL SAFETY PRECA UTIONS 8 – English • The brake is applied when the front hand guard (B) is pushed forw ards. • This mov ement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum).
GENERAL SAFETY PRECA UTIONS English – 9 of the front hand guard, the chain brake can only be activated b y the iner tia action. Will m y hand alwa ys activate the chain brake during a kickbac k? No . It takes a certain force to mov e the hand guard forw ard.
GENERAL SAFETY PRECA UTIONS 10 – English chain saw , including the cutting equipment, is insulated from the handles by vibration damping units . Cutting hardwoods (most broadleaf trees) creates more vibr ation than cutting softwoods (most conif ers).
GENERAL SAFETY PRECA UTIONS English – 11 • Keep the chain pr operly tensioned! If the chain is slack it is more lik ely to jump off and lead to increased wear on the bar , chain and drive sproc ket.
GENERAL SAFETY PRECA UTIONS 12 – English Sharpening y our chain and adjusting depth gauge setting General information on sharpening cutting teeth • Nev er use a blunt chain. When the chain is blunt y ou hav e to ex er t more pressure to f orce the bar through the wood and the chips will be very small.
GENERAL SAFETY PRECA UTIONS English – 13 General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. T o maintain optimal cutting performance the depth gauge (B) has to be filed down to achie v e the recommended depth gauge setting.
GENERAL SAFETY PRECA UTIONS 14 – English Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather .
GENERAL SAFETY PRECA UTIONS English – 15 Regular ly check the degree of wear on the drive sproc ket. Replace if wear is e xcessive. Replace the dr ive sproc ket whenev er you replace the chain. Needle bearing lubrication Both v ersions of sproc kets hav e a needle bearing on the drive shaft, which has to be greased regularly (once a week).
ASSEMBL Y 16 – English Fitting the bar and chain Check that the chain brak e is in disengaged position by moving the front hand guard tow ards the front handle. Remov e the bar nuts and remo v e the clutch cov er (chain br ake). T ake off the transportation r ing (A).
FUEL HANDLING English – 17 Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys be run using a mixture of petrol and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.
FUEL HANDLING 18 – English Fuelling Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly . The fuel filter must be replaced at least once a year . Contamination in the tanks causes malfunction. Make sure the fuel is w ell mixed b y shaking the container before refuelling.
ST AR TING AND ST OPPING English – 19 Starting and stopping Cold engine Starting: The chain brake must be engaged when the chain saw is started. Activate the brak e by moving the front hand guard forw ards. Ignition; choke: Set the choke control in the chok e position.
ST AR TING AND ST OPPING 20 – English Push in the choke control as soon as the engine fires and keep pulling until the engine starts. When the engine star ts, quic kly apply full throttle; the throttle star t lock will automatically disengage.
W ORKING TECHNIQUES English – 21 Bef ore use: 1 Check that the chain brak e w orks correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged.
W ORKING TECHNIQUES 22 – English Fit a guard to the bar before tr anspor ting the chain saw or carrying it for any distance . 7 When you put the chain sa w on the ground, lock the sa w chain using the chain brak e and ensure you ha ve a constant view of the machine.
W ORKING TECHNIQUES English – 23 the saw chain is jamming, the sa w may be pushed back at y ou. 8 Unless the user resists this pushing force there is a r isk that the chain saw will mov e so far bac kwards that only the kickbac k zone of the bar is in contact with the tree, which will lead to a kickbac k.
W ORKING TECHNIQUES 24 – English Limbing When limbing thick branches y ou should use the same approach as for cutting. Cut difficult branches piece by piece . Cutting If you ha ve a pile of logs, each log y ou attempt to cut should be remov ed from the pile, placed on a saw horse or runners and cut individually .
W ORKING TECHNIQUES English – 25 Felling direction The aim is to fell the tree in a position where y ou can limb and cross-cut the log as easily as possible.
W ORKING TECHNIQUES 26 – English Ne xt mak e the bottom cut so that it finishes e xactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45 ° .
W ORKING TECHNIQUES English – 27 Freeing a tree that has fallen badl y Freeing a ”trapped tree” It is very dangerous to remove a tr apped tree and there is high accident risk. Nev er try to fell the tree that is trapped. Nev er work in the risk zone of the hanging trapped tree.
W ORKING TECHNIQUES 28 – English Ho w to a v oid kickbac k What is kic kback? The word kickbac k is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar , known as the kickbac k zone, touches an object.
MAINTENANCE English – 29 General The user must only carry out the maintenance and service work descr ibed in this manual. Carburettor adjustment Due to existing en vironmental and emissions legislation your chain sa w is equipped with movement limiters on the carburettor adjuster scre ws.
MAINTENANCE 30 – English ev ery position and the engine speed should be safely below the speed at which the chain starts to rotate. High speed jet H At the factory the engine is adjusted at sea level.
MAINTENANCE English – 31 Checking the inertia brake release Place the chain saw , with the engine s witched off , on a stump or other stable surf ace. Release the front handle and let the saw f all b y its own weight, rotating around the rear handle towards the stump .
MAINTENANCE 32 – English Chain catcher Chec k that the chain catcher is not damaged and is firmly attached to the body of the chain saw . Right hand guar d Chec k that the right hand guard is not damaged and that there are no visible def ects, such as crac ks.
MAINTENANCE English – 33 The muffler is designed to reduce the noise le vel and to direct the exhaust gases a wa y from the operator . The exhaust gases are hot and can contain sparks, which ma y cause fire if directed against dry and combustible material.
MAINTENANCE 34 – English Fitting the starter • T o fit the star ter, first pull out the starter cord and place the star ter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls. • Fit and tighten the screws that hold the starter.
MAINTENANCE English – 35 Adjustment of the oil pump The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner .
MAINTENANCE 36 – English Winter use Running problems can occur when using the machine in the cold and snowy conditions caused by: • T oo low engine temperature.
English – 37 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be perf ormed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekl y maintenance Monthly maintenance Clean the outside of the machine.
38 – English TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound pow er (L WA ) in conformity with EC directive 2000/14/ EC.
English – 39 TECHNICAL D A T A Bar and chain combinations The follo wing cutting attachments are approv ed for the models Jonsered CS 2156, CS 2156C , CS 2156CWH, CS 2159, CS 2159W , CS 2159WH, CS 2159C and CS 2159CWH. Sa w c hain filing and file gauges Bar Chain Length, inch Pitch, inch Gauge, mm Max.
40 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-561 82 Huskv arna, Sweden, tel: +46-36-146500, declares under sole responsibility that the ch.
.
.
.
1153185-26 ´®z+U2T¶6X¨ ´®z+U2T¶6X¨ 2010-03-22 Original instructions.
デバイスHusqvarna CS 2159Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna CS 2159Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna CS 2159Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna CS 2159Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna CS 2159Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna CS 2159Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna CS 2159Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna CS 2159Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna CS 2159Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。