HusqvarnaメーカーFT900の使用説明書/サービス説明書
ページ先へ移動 of 28
Owner's Manual 532 43 99-99 FT900 "This machine is approved by the EP A for E10 (10% ethanol) and lower fuel only . Do not use any fuel >E10 in this machine.
2 • Do not run the engine indoors; exhaust fumes are dangerous. • Never operate the tiller without proper guards, plates, or other safety protective devices in place. • Keep children and pets away . • Do not overload the machine capacity by attempting to till too deep at too fast a rate.
3 PRODUCT SPECIFICA TIONS Gasoline Capacity: 3 Quarts (2.8L) Unleaded Regular Oil (API-SG-SL): SAE 30 (Above 32°F/0°C) (Capacity: 21 oz./0.6L) SAE 5w30 (Below 32°F/0°C) Spark Plug : Champion RC12YC (Gap: .030"/0.76mm) T ABLE OF CONTENTS SAFETY RULES .
4 AS SEMBL Y OPERA TOR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the operating position (standing behind tiller handles). TOOLS REQUIRED FOR AS SEMBL Y A socket wrench set will make assembly easier .
5 AS SEMBL Y Fig. 3 INST ALL DEPTH ST AKE AS SEMBL Y (See Fig. 3) • Loosen nut “ A ”. • Insert stake support between engine bracket halves with stake spring down. • Bolt stake support to engine brackets with bolts, lock washers and nuts. Tighten se curely .
6 KNOW YOUR TILLER READ THIS MANUAL AND SAFETY RULES BEFORE OPERA TING Y OUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your Tiller or in literature supplied with the product.
7 OPERA TION dep t h_stake_4 Fig. 6 DEPTH ST AKE HAIRPIN CLIP AND CLEVIS PIN ST AKE SPRING WHEEL 00155 The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your til- ler and while tilling.
8 OPERA TION e ng i n e_ a r t_ 4 OIL FILLER PLUG OIL LEVEL Fig. 7 TO TRANSPORT CAUTION: Before lifting or trans port ing, allow tiller engine and muffler to cool. Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE Y ARD • Tip depth stake forward until it is held by the stake spring.
9 OPERA TION Fig. 9 321 5 4 67 Fig. 10 Fig. 8 en g in e _a r t _ 7 1 RECOIL ST ARTER THROT TLE CON TROL CHOKE CON TROL SP ARK PLUG BREAKING IN YOUR TILLER Break-in your belt(s), pulleys and tine control before you actually begin tilling. • Start engine, tip tines off ground by pressing handles down and engage tine control to start tine rotation.
10 MAINTENANCE GENERAL RECOMMENDA TIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. T o receive full value from the warranty , operator must maintain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller .
11 MAINTENANCE engine_ar t _12 Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance.
12 MAINTENANCE MUFFLER Do not operate tiller without muffler . Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary . If your engine is equipped with a spark arrester screen assembly , remove every 50 hours for cleaning and inspection.
13 CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. SERVICE AND ADJUSTMENTS TILLER TO ADJUST HANDLE HEIGHT (See Fig. 15) F actory assembly has provided lowest handle height. Se lect handle height best suited for your tilling conditions.
14 TO REPL ACE V -BEL TS (See Figs. 21 and 22) Replace V -belts if they have stretched considerably or if they show cracks or frayed edges. There are two (2) V -belts - forward (inside) and reverse (outside). Belt guard must be removed to service belts.
15 SERVICE AND ADJUSTMENTS belts 10 BEL T GUIDE REVERSE IDLER PULLEY BEL T GUIDE TRANSMISSION PULLEY FORWARD IDLER PULLEY REVERSE IDLER PULLEY IDLER ARM PIN ENGINE PULLEY FRONT VIEW REFERENCE REVERSE (OUTSIDE) V -BEL T FORWARD MOTION (INSIDE) V -BEL T ENGINE PULLEY REVERSE IDLER PULLEY ENGINE PULLEY FORWARD IDLER PULLEY Fig.
16 STORAGE ENGINE OIL Drain oil (with engine warm) and replace with clean oil. (See “ENGINE” in the Maintenance section of this man ual). CYLINDER(S) • Remove spark plug. • Pour 1 ounce (29 ml) of oil through spark plug hole into cylinder . • Pull starter handle slowly several times to distribute oil.
17 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in the Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Dirty air cleaner .
18 KEY P ART NO . NO. DESCRIPTION 1 532 44 07-18 P anel, Control 2 872 14 05-12 Bolt, RDHD 5/16-18 x 1 1/2 3 532 16 57-87 Grip, Handle 4 532 44 07-14 Handle, LH Double Bend 5 873 68 05-00 Nut, Crown Lock 5/16 -18 6 819 11 11-16 Washer 11/32 x 11/16 x 16 Ga.
19 41 1 2 3 4 5 42 6 7 8 29 11 9 17 31 30 29 11 11 11 10 14 15 12 12 13 16 19 32 18 20 25 21 22 23 24 26 28 27 belt_guard_14 KEY P ART NO . NO. DESCRIPTION 1 532 43 91-62 Assembly , Bracket, Belt Guar.
20 KEY P ART NO . NO. DESCRIPTION WHEEL?DSTAKE? KEY P ART NO . NO.
21 KEY P ART NO . NO. DESCRIPTION 3 1 6 4 5 6 2 2 tine_ipb_3 KEY P ART NO . NO. DESCRIPTION 4 532 15 69-31 Tine, Inner , L.H. 5 532 15 69-33 Tine, Outer , L.H. 6 532 00 49-29 Rivet P an Hd Drilled 1/4 Dia. 1 532 15 69-34 Tine, Outer , R.H. 2 532 00 31-46 Retainer , Spring 3 532 15 69-32 Tine, Inner , R.
22 KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION 14 532 00 91-73 Spacer , Split 16 819 09 14-12 Washer 9/32 x 7/8 x 12 Ga. 17 819 09 20-16 Washer 9/32 x 1-1/4 x 16 Ga. 18 810 04 04-00 Washer , Lock 1/4 19 874 61 04-12 Bolt, Hex 1/4-28 x 3/4 Gr .
23 KEY P ART NO . NO. DESCRIPTION 1 532 44 06-13 Decal, Logo 2 532 42 20-12 Decal, Logo 3 532 43 99-89 Decal, Logo 5 532 11 06-14 Decal, Hand Placement 6 532 15 87-00 Decal, Control Forward 7 532 15 8.
24 &RQVXPHU:KHHOHG3URGXFWV ±/LPLWHG:DUUDQW +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV + XVTYDUQD SURGXFW LV IUHH IUR.
25 F 3UHYHQWDWLYHPDLQWHQDQ FHDVRXWOLQHGLQWKH RSHUDWRU¶VPDQXDO ,Q DGGLWLRQ RX PXVWFHDVH XVLQJ WKH SURGXFW LPPHGLDWHO XSRQ DQ IDLOXUH.
26 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
27 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
11.29.10 CL Printed in the U.S.A..
デバイスHusqvarna FT900の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna FT900をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna FT900の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna FT900の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna FT900で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna FT900を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna FT900の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna FT900に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna FT900デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
