HusqvarnaメーカーGTH2350の使用説明書/サービス説明書
ページ先へ移動 of 48
02490 GTH2350 Owner's Manual.
2 I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine. • Clear the area of objects such as rocks, toys, wire, etc.
3 Safe Operation Practices for Ride-On Mowers SAFETY RULES • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. • Never carry passengers or children even with the blades off. • Do not mow in reverse unless absolutely necessary.
4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 5.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: W/ FILTER: 4.5 PINTS W/O FILTER: 4.0 PINTS SPARK PLUG: CHAMPION: RC12YC (GAP: .030") GROUND SPEED (MPH): FORWARD: 0 – 5.
5 UNASSEMBLED P ARTS Steering Wheel Insert Steering Wheel Mower Gauge Wheels (2) Wheels (2) Locknuts 3/8-16 (2) Shoulder Bolts Nose Roller (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys K.
6 ASSEMBL Y HOW TO SET UP YOUR TRACT OR CHECK BATTERY (See Fig. 2) • Lift hood to raised position. • If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps.
7 INSTALL SEAT (See Fig. 3) Adjust seat before tightening adjustment knob. • Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. • Pivot seat upward and remove from the cardboard packing.
8 ASSEMBL Y INST ALL MOWER AND DRIVE BEL T (See Figs. 5 and 6) Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage parking brake. • Cut and remove ties securing anti-sway bar and belts. Swing anti-sway bar to left side of mower deck.
9 ASSEMBL Y CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models onl.
11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR. Compare the illustrations with your tractor to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
12 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
13 OPERA TION FIG. 10 TO OPERATE MOWER (See Fig. 9) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut.
14 OPERA TION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).
15 OPERA TION MOWING TIPS • Tire chains cannot be used when the mower housing is attached to tractor. • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.
16 B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridg.
17 CUST OMER RESPONSIBILITIES FIG. 12 MANDREL ASSEMBLY BLADE TRAILING EDGE UP FLAT WASHER LOCK WASHER BLADE BOLT (GRADE 8)* *A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD. CENTER HOLE STAR TRACT OR Always observe safety rules when performing any mainte- nance.
18 CUST OMER RESPONSIBILITIES V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating.
19 CUST OMER RESPONSIBILITIES FIG. 16 FUEL FILTER CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax.
20 SER VICE AND ADJUSTMENTS TO LEVEL MOWER HOUSING Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.
21 SER VICE AND ADJUSTMENTS TO REPLACE MOWER DRIVE BELT MOWER DRIVE BELT REMOVAL (See Fig. 21) - • Park tractor on a level surface. Engage parking brake. • Remove screws from L.H. mandrel cover and remove cover. • Roll belt over the top of L.H. mandrel pulley.
22 FIG. 24 TO REPLACE MOTION DRIVE BELT (See Fig. 24) Park the tractor on level surface. Engage parking brake. For ease of service there is a belt installation guide decal on bottom of left footrest. • Remove mower (See “TO REMOVE MOWER” in this section of this manual.
23 SER VICE AND ADJUSTMENTS ADJUSTMENT BOLT FIG. 25 TRANSMISSION REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation before operating the tractor. See “PURGE TRANSMISSION” in Operation section of this manual.
24 TO START ENGINE WITH A WEAK BATTERY (See Fig. 29) WARNING : Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged.
25 SER VICE AND ADJUSTMENTS IDLE FUEL ADJUSTING NEEDLE IDLE SPEED ADJUSTING SCREW STOP SCREW CLAMP SCREW CHOKE CONTROL CABLE THROTTLE CONTROL CABLE ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32) The throttle control has been preset at the factory and adjustment should not be necessary.
26 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
28 Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves corrected, contact an authorized service center/ seat with attachment department. clutch engaged Poor cut - uneven 1.
29 BATTERY FUSE RED RED BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BROWN RED ORANGE BROWN M SOLENOID WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
30 30 33 40 26 28 50 29 25 42 12 12 11 10 8 2 1 27 16 81 48 22 79 21 46 89 REP AIR P ARTS TRACTOR - - MODEL NO. GTH2350 (GTHK2350A), PRODUCT NO. 954 56 85-40 ELECTRICAL.
31 KEY P ART N O . N O . DESCRIPTION 1 532 14 49-27 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 12 48-86 Tray, Battery 1 0 532 14 52-11 Bolt, Battery Front 1/4-20 x 7.5 Zinc 1 1 532 15 01-09 Holddown Battery Front Mount 1 2 532 14 57-69 Nut, Push Nylon 1.
32 31 68 43 34 47 24 39 17 86 4 2 19 20 16 17 56 21 47 17 28 91 1 36 36 50 17 17 17 60 60 44 17 8 156 17 6 7 7 7 30 45 17 99 35 5 140 141 14 18 130 130 158 37 17 17 58 161 162 144 17 130 142 17 130 32 17 139 17 33 139 122 150 122 148 153 15 25 130 138 156 156 152 146 143 137 20 119 165 166 84 159 REP AIR P ARTS TRACTOR - - MODEL NO.
33 1 532 18 03-72 Rail, Frame RH 2 532 17 52-82 Drawbar, Gt 4 873 80 07-00 Nut, Lock Hex 7/16 Unc 5 532 17 75-82 Dash, Plastic 6 532 15 78-82 Dash, 1PCS, Lower 7 817 72 04-08 Screw, Thd Cut 1/4-20 x 1/2 8 532 14 51-66 Support, Battery 1 4 532 17 75-83 Hood Asm.
34 9 7 55 65 130 131 34 35 37 38 40 41 42 68 46 36 37 38 64 39 56 29 89 132 77 70 74 89 148 89 133 120 98 112 123 94 94 126 138 23 114 73 120 127 153 143 48 120 117 52 129 50 117 48 128 142 58 77 152 151 135 137 6 22 124 125 111 121 122 114 20 147 146 61 1 2 2 69 33 3 145 107 106 108 145 69 33 3 117 REP AIR P ARTS TRACTOR - - MODEL NO.
35 1 - - - - - - - Transaxle Hydro Gear 331-3000 (Order Parts From Transaxle Manufacturer) 2 532 00 70-70 Key 1/4 x 2.5 3 532 00 75-63 W asher 6 876 02 04-12 Pin, Cotter 7 532 14 05-07 Wheel, Hub Asse.
36 47 48 46 49 50 8 6 29 28 23 31 41 22 21 20 1 45 14 25 34 33 32 6 27 42 27 6 19 15 14 35 18 16 9 8 7 2 6 6 4 14 15 14 14 15 12 9 3 8 7 3 6 6 5 13 13 7 8 14 15 14 14 36 38,40 37,39 17 14 26 10 11 44 REP AIR P ARTS TRACTOR - - MODEL NO. GTH2350 (GTHK2350A), PRODUCT NO.
37 1 532 16 66-27 Wheel, Steering 2 532 17 85-57 Axle Asm., Front 3 532 12 48-36 Fitting, Grease 4 532 16 18-49 Spindle Asm, LH 5 532 16 18-48 Spindle Asm.
38 1 84 47 24 12 11 41 42 43 10 9 8 40 29 SPARK ARRESTER KIT 84 80 39 18 15 17 37 28 37 27 26 16 21 20 22 25 74 81 82 62 70 71 80 69 83 35 2 REP AIR P ARTS TRACTOR - - MODEL NO.
39 KEY P AR T N O . N O . DESCRIPTION 1 - - - - - - - Engine Kohler Model No. CV675 (Order parts from engine manufacturer) 2 532 14 97-23 Muffler Side 8 532 12 13-61 Pulley V-Idler 9 532 17 77-48 Keeper Asm.
40 1 10 5 18 19 16 15 12 13 17 4 14 2 6 37 21 7 7 5 20 8 20 8 3 1 532 14 08-40 Sea t 2 532 14 05-51 Bracket, Pivot Seat 3 532 14 06-75 Strap, Fender 4 532 12 70-18 Bolt Shoulder 5/16-18 x .
41 WHEELS & TIRES 6 12 2 1 3 11 4 10 5 9 8 7 9 8 4 10 6 17 24 1 532 18 23-91 Decal, Replacement Parts 2 532 17 67-75 Decal, Engine 3 532 18 16-62 Decal, Hood, RH 4 532 18 16-63 Decal, Hood, LH 6 5.
42 35 73 34 32 31 30 4 5 5 4 2 11 11 7 9 10 3 6 1 14 41 14 41 13 13 23 23 23 23 38 39 40 43 42 29 70 82 72 26 12 78 24 75 76 76 23 80 8 REP AIR P ARTS TRACTOR - - MODEL NO.
43 1 532 12 10-06 Rod Asm., Lever 2 532 18 00-45 Shaft Asm., Lift Vgt 3 532 15 91-89 Lever Asm., Lift Rh 4 812 00 00-22 E-Ri ng Truarc #5133-87 5 819 29 20-16 Washer 29/32 x 1-1/4 x 16 Ga.
44 2 25 24 55 46 27 39 45 44 43 45 44 51 45 56 48 48 45 53 52 38 50 48 49 63 47 45 27 28 27 31 30 30 32 33 45 27 31 40 32 66 37 33 65 2 45 61 36 4 3 5 6 6 7 54 34 35 36 2 3 3 42 99 15 14 16 13 11 10 9 8 2 19 20 2 19 21 22 18 17 23 1 45 62 2 94 95 98 97 29 96 29 94 97 6 60 6 60 57 59 58 67 64 114 11 11 REP AIR P ARTS TRACTOR - - MODEL NO.
45 REP AIR P ARTS TRACTOR - - MODEL NO. GTH2350 (GTHK2350A), PRODUCT NO. 954 56 85-40 MOWER DECK KEY P ART N O . N O . DESCRIPTION KEY P ART N O . N O . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 18 30-56 Deck Asm.
46 SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the.
47 15 DEGREES MAX. F O L D A L O N G D O T T E D L IN E T H IS IS A 15 D E G R E E S L O P E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
532 18 06-66 Rev. 2 07.18.02 RH Printed in U.S.A..
デバイスHusqvarna GTH2350の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna GTH2350をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna GTH2350の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna GTH2350の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna GTH2350で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna GTH2350を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna GTH2350の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna GTH2350に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna GTH2350デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
