HusqvarnaメーカーLGT24K54の使用説明書/サービス説明書
ページ先へ移動 of 48
LGT24K54 Owner's Manual 07002 532 44 17-90 Rev . 1 Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty .
2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AIL URE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS (5) Large Retainer Springs (1) Small Retainer Springs 6 1 / 3 - 1 ) 5 ( s r e h s a W . D . O (2) Rear Lift Link Assemblies (1) Front Lift Link Assembly (1) Anti- Sway Bar (1) 3/4 O.D. Washers (1) Small Retainer Springs (1) 1-1/4 O.
6 Fig. 1 Fig. 2 ADJUST SEA T (See Fig. 2) • Sit in seat. • Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down. • Release lever to lock seat in position.
7 AS SEMBL Y TRANSAXLE 02965 FRONT BACK ENGINE Q. DEFLECTOR SHIELD Q Fig. 6 90° END INTEGRA TED WASHER END ANTI-SWA Y BAR (S) TOWARDS TOW ARDS TRANSAXLE MOWER DECK • F rom right side of mower , first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle.
8 AS SEMBL Y 6. A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 12) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor .
9 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly leveled.
10 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP ARE.
11 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING Y OUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
12 Fig. 17 TO USE CHOKE CONTROL (N) (See Fig. 19) Use choke control whenever you are starting a cold engine. Do not use to start a warm engine. • T o engage choke control, pull knob out. Slowly push knob in to disengage. The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age.
13 TO ADJUST MOWER CUT TING HEIGHT (See Fig. 21) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. TO ADJUST GAUGE WHEELS (See Fig. 22) Gauge wheels are prop er ly ad just ed when they are slight ly off the ground when mower is at the desired cutting height in operating position.
14 Fig. 25 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous.
15 SERVICE REMINDER/HOUR METER Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. T o service engine and mower , see the Maintenance section of this manual.
16 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time.
17 T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil.
18 TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
19 V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling.
20 Fig. 30 DECK WASHOUT PORT (See Fig. 32) Y our tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
21 WARNING: TO A VOID SE RI OUS IN JU RY , BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position.
22 Fig. 36 FRONT -TO-BACK ADJUSTMENT (See Fig. 37 and 38) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
23 TO REMOVE WHEEL FOR REP AIRS (See Fig. 40) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle.
24 TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 42) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged.
25 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. TO REMOVE HOOD AND GRILL ASSEMBL Y (See Fig.
26 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
27 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
28 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
29 NO TES M FUSE ST ARTER SOLENOID BA TTER Y ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HO.
30 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V Out.
31 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 8 532 18 64-91 B.
32 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 CHASSIS 297 191 176 14 130 130 202 203 208 18 15 25 207 5 176 176 205 206 137 137 214 204 151 Chassis-t ex_ GT HUSQ_I I_39 3 1.
33 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 CHASSIS KEY P ART NO . NO. DESCRIPTION 3 532 43 97-52 Logo 5 532 43 74-72 Dash 14 532 44 11-77 Hood 15 532 43 97-33 Lens LH 18.
34 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 DRIVE 56 216 143 197 196 125 226 227 125 80 125 51 231 170 175 279 176 178 174 22 23 166 232 153 233 drive-tex_K46_fender_6_r4.
35 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 - - - - - - - - - T ransaxle, TUFFTORQ K46 AW 2 532 18 62-11 Key 7 532 19 98-44 Hub Asm.
36 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 ENGINE 1 92 12 11 41 42 85 9 29 SP ARK ARRESTER KIT 92 45 90 37 28 37 21 20 22 62 70 71 86 69 87 2 engine-tex_Ka wa-2cyl_7 18 15 91 14 KEY P ART NO . NO. DESCRIPTION KEY P ART NO .
37 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 STEERING ASSEMBL Y 6 5 13 13 53 8 9 9 8 8 7 7 62 4 35 16 19 63 63 57 60 59 58 28 13 22 64 70 68 69 67 67 66 15 15 14 14 21 51 26 1 45 61 2 6 steering-tex_LEGND2_18_r1 KEY P ART NO .
38 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO. DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
39 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 SEA T AS SEMBL Y 1 532 43 48-22 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/Ins.
40 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 MOWER DECK mower_dec k 54-tex_18_r3 47 7 49 46 32 33 31 30 1 33 52 52 43 196 97 33 192 49 34 39 185 46 46 6 21 122 114 98 31 3.
41 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 44 15-47 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm.
42 TRACTOR - MODEL NO . LGT24K54 (96043012701), PRODUCT NO . 960 43 01-27 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 91 lift-tex_3 89 87 89 87 2 532 42 20-27 Shaft Asm.
43 15 DEGREES MA X . FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING : To a v oid serious injury, operate your tractor up and down the f ace o f slopes, ne v er across the f ace.
44 &RQVXPHU:KHHOHG3URGXFWV ±/LPLWHG:DUUDQW +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV + XVTYDUQD SURGXFW LV IUHH IUR.
45 F 3UHYHQWDWLYHPDLQWHQDQ FHDVRXWOLQHGLQWKH RSHUDWRU¶VPDQXDO ,Q DGGLWLRQ RX PXVWFHDVH XVLQJ WKH SURGXFW LPPHGLDWHO XSRQ DQ IDLOXUH.
46 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
47 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLR.
02.22.11 CL Printed in the U.S.A..
デバイスHusqvarna LGT24K54の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna LGT24K54をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna LGT24K54の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna LGT24K54の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna LGT24K54で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna LGT24K54を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna LGT24K54の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna LGT24K54に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna LGT24K54デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
