HusqvarnaメーカーLTH2042の使用説明書/サービス説明書
ページ先へ移動 of 44
02494 L TH2042 Owner's Manual 02578_husqvarna.
2 DO NO T : • Do not turn on slopes unless necessar y , and then, turn slowly and gradually downhill, if possib le. • Do not mow near drop-offs , ditches, or embankments. The mower could suddenly turn ov er if a wheel is ov er the edge of a cliff or ditch, or if an edge cav es in.
3 W ARNING: In order to prevent ac- ci den tal starting when setting up, trans por t ing, ad just ing or making re- pairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, you ma y lose control of the tractor .
4 GASOLINE CAP A CITY 4.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W30 (abov e 32°F) SAE 5W -30 (below 32°F) OIL CAP A CITY : 3.0 PINTS SP ARK PLUG: CHAM PI ON RC12YC (GAP: .030") GROUND SPEED (MPH): F orward: 0-5.5 Re verse 0-2.
5 UNASSEMBLED P AR TS (1) Large Flat Washer Steering Wheel Insert Steering Sleeve Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys Slope Sheet Steering Extension Shaft Steering Adapter (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 (4) Washers 3/8 x 3/4 x 14 Ga.
6 02601 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Stan dard wrench sizes are listed. Utility knif e Pliers (1) 3/4" wrenches Tire pressure gauge (2.
7 ASSEMBL Y FIG. 3 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T HO W T O SET UP Y OUR TRA CT OR INST ALL SEA T (See Fig. 3) Adjust seat bef ore tightening adjustment knob. • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor .
8 ASSEMBL Y ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRAC- T OR, WE WISH TO ASSURE THA T Y OU RECEIVE THE BEST PERFORMANCE AND SA TISF ACTION FR OM THIS QU ALITY PRODUCT . PLEASE REVIEW THE FOLLOWING CHECKLIST : ✓ All assemb ly instructions have been completed.
9 OPERA TION These symbols ma y appear on your tractor or in literature supplied with the product. Lear n and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models .
10 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRACT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments. Sav e this manual f or future ref erence.
11 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age. Al ways wear safety glass es or eye shields while operating your tractor or per form ing an y adjustments or repairs.
12 OPERA TION T O OPERA TE ON HILLS W ARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across an y slope. • Choose the slo west speed bef ore star ting up or down hills. • A void stopping or changing speed on hills .
13 OPERA TION FIG. 9 ADD GASOLINE • Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead o xide deposits and reduce valv e life).
14 FIG. 10 MO WING TIPS • Mower should be properly lev eled for best mowing per- f or mance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mow er should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut.
15 MAINTENANCE BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartri.
16 MAINTENANCE BLADE REMO V AL (See Fig. 11) • Raise mower to highest position to allow access to blades . • Remov e blade bolt, loc k washer and fl at washer se cur ing bla de. • Install new or resharpened blade with trailing edge up tow ards deck as shown.
17 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from w ear . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling.
18 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whichev er occurs fi rst.
19 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS • Depress clutch/brake pedal full y and set parking brake. • Place motion control le ver in neutral (N) position. • Place attachment clutc h in “DISENGAGED” position.
20 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 19 NUT "F" FRONT LINKS FIG. 20 FRONT -T O-BACK ADJUSTMENT (See Figs .
21 SER VICE AND ADJUSTMENTS FIG. 21 T O REPLACE MO WER BLADE DRIVE BEL T (See Fig. 21) The mower b lade drive belt ma y be replaced without tools. P ark the tractor on lev el surface. Engage par king brake . BEL T REMO V AL - • Remov e mow er from tractor (See “T O REMO VE MO W ER” in this section of man ual).
22 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 25) • Block up axle securely . • Remov e axle cover , retaining r ing and washers to allow wheel remov al (rear wheel contains a square ke y - Do not lose). • Repair tire and reassemble .
23 SER VICE AND ADJUSTMENTS T O REPLACE HEADLIGHT B ULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push b ulb holder securely back into the hole in the bac kside of the grill. • Close hood.
24 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark.
25 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes before attempting to start. 4. Bad spar k plug.
26 TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-saf ety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an author ized service center/ with attachment clutc h depar tment.
27 BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACK BROWN BLACK BLACK .
28 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 30 12 12 11 10 8 2 1 27 52 16 16 D .
29 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 14 49-27 Batter y 2 874 76 04-12 Bolt He x Hd 1/4-20 unc x 3/4 8 532 12 48 86 T ra y Batter y 10 532 14 52-11 Bolt 1/4-20 x 7.
30 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 CHASSIS AND ENCLOSURES 64 74 10 30 208 13 208 11 209 31 1 209 2 9 209 208 209 5 5 207 144 26 26 60 26 144 26 10 209 209 142 209 142 143 60 145 37 37 18 206 14 14 38 38 219 20 219 23 17 261 28 259 260 258 166 39 90 159 217 212 chassis-husqy .
31 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 CHASSIS AND ENCLOSURES KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .
32 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DRIVE 66 29 28 32 30 52 32 59 38 61 41 53 35 55 36 62 35 36 22 39 34 16 1 77 77 30 52 56 64 65 212 63 116 7.
33 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv e in U .S. inches. 1 inch = 25.4 mm. 1 - - - - - - - - T ransaxle Hydro Gr Model 314-0510 (Order par ts from transaxle mfg.
34 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 STEERING ASSEMBL Y 5 5 3 43 95 43 8 10 40 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 44 51 54 68 67 67 67 13 65 68 15 15 15 29 29 82 4 32 26 30 28 steering_pl.
35 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 532 16 66-27 Wheel Steering 2 532 18 47-06 Axle Asm 3 532 16 98-40 Spindle Asm LH 4 532 16 98-39 Spindle Asm RH 5 532 12 49-31 Bearing Race Thrust Harden 6 532 12 17-48 W asher 25/32 x 1-5/8 x 16 Ga.
36 1 532 17 08-05 Control Throttle/Choke Flag 2 817 72 04-08 Screw He x Thd Cut 1/4-20 x 1/2 3 - - - - - - - - Engine, K ohler SV600 (Order par ts from engine manuf ac- turer) 4 532 18 86-55 Muffl er.
37 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 19 01-20 Seat 2 532 14 05-51 Brac ket Piv ot Seat 8 720 3 871 11 06-16 Bolt Fin He x 3/8-16 unc X 1 4 819 13 16-10 W asher 13/32 x 1 x 10 Ga. 5 532 14 50-06 Clip Push-In 6 873 80 06-00 Nut He x w/Ins.
38 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DECALS KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO .
39 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER LIFT 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 12 11 31 32 31 32 19 19 13 13 13 13 lift-rh.
40 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER DECK 15 14 13 11 10 9 8 16 68 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 54 52 53 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 48 59 19 4 5 6 21 40 143 36 40 40 159 140 184 42_D_man-t-path_stlt_4.
41 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER DECK 1 532 18 20-32 Deck Asm 42"weldment 2 872 14 05-06 Bolt Rdhd Sqnk 5/16-18 unc x 3/4 3 532 .
42 SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from t.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
44 532 18 99-02 Re v . 2 5.26.04 RD/MH Printed in U.S .A..
デバイスHusqvarna LTH2042の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna LTH2042をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna LTH2042の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna LTH2042の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna LTH2042で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna LTH2042を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna LTH2042の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna LTH2042に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna LTH2042デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
