HusqvarnaメーカーRZ46215の使用説明書/サービス説明書
ページ先へ移動 of 40
Operator Manual Please read the operator man ual carefull y and mak e sure y ou understand the instructions befor e using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will v oid the product war ranty .
©2013 All rights reserved. Orangeburg, SC Printed in U.S.A. When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling. T o implement improvements, specifications and designs can be altered without prior notification.
CONTENTS INTRODUCTION ............................................................... 4 Driving and T ranspor t on Public Roads ...................... 4 T owing ......................................................................... 4 Operating ....
4 INTRODUCTION Congratulations Thank you for purchasing a Husqvarna ride-on mower . This machine is built for superior efficiency to rapidly mow primarily large areas. A contr ol panel easily accessible to the operator and a hydrostatic transmission r egulated by steering controls both contribute to the machine’s perfor mance.
5 INTRODUCTION Good Service Husqvarna's products are sold only in specialized r etail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the pr oduct is delivered, the machine has, for example, been inspected and adjusted by your retailer .
R N 6 SYMBOLS AND DECALS These symbols are found on the machine and in the operator manual. Study them carefully so that you know what they mean. IMPORT ANT INFORMA TION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. W ARNING ! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx.
7 SAFETY • Read, understand, and follow all instructions on the machine and in the manual before starting. • It is recommended that someone be aware that you are mowing and can provide help in case of injury or accident. • Do not put hands or feet near rotating parts or under the machine.
8 SAFETY Slope Operation Slopes are a major factor r elated to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requir es extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.
9 SAFETY • Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner . Always place containers on the ground away fr om the vehicle when filling. • Remove gas-powered equipment fr om the truck or trailer and refuel it on the gr ound.
10 SAFETY • The machine is tested and approved only with the equipment originally provided or r ecommended by the manufacturer . Only use approved r epair parts for the machine. • The blades are sharp and can cause cuts and gashes. Wrap the blades or use pr otective gloves when handling them.
11 CONTROLS This operator manual describes the Husqvarna Zero T ur n Rider . The rider is fitted with a Kawasaki four -str oke overhead valve engine. T ransmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and ther eby the direction and speed.
Forward Neutral Reverse Neutral Lock 12 CONTROLS Steering Control Levers W ARNING ! The machine can turn very rapidly if one steering control is moved much further forward than the other . The machine’s speed and direction ar e continuously variable using the two steering controls.
13 CONTROLS Blade Switch Throttle Control The throttle contr ol regulates the engine speed and ther eby the rate of rotation of the blades, assuming the blade switch is pulled out, see Engaging the Mower Deck. T o increase or decr ease the engine speed, the contr ol is moved forward or back r espectively .
14 CONTROLS Fuse The 20 amp primary fuse is located on the left hand side of the machine. It is accessed by tilting the seat forward. The fuse is a flat pin type used in automobiles. Fuel Shut Off V alve The fuel shut off valve is located at the left r ear of the seat.
15 CONTROLS Fuel T ank IMPORT ANT INFORMA TION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.
16 OPERA TION Read the Saf ety section and following pages, if you are unfamiliar with the machine. T raining Due to unique steering capabilities, zero turn mowers are far more maneuverable than typical riding mowers. This section should be reviewed in its entir ety prior to attempting to move the mower under its own power .
17 OPERA TION Starting the Engine 1. Sit on the seat. 2. Raise the mower deck by pushing the release button on the top of the lifting lever . Pull the lifting lever backward to the locked (transport) position. 3. Activate the park brake by pushing the release button in and pulling the lever fully upwards.
18 OPERA TION Running 1. Release the park brake by pushing the top release button in and moving the lever downward. NO TE: The mower is equipped with an oper ator presence system. When the engine is running, any attempt b y the operator to lea ve the seat without first setting the park brak e will shut off the engine.
19 OPERA TION 4. Raise the mower deck by pressing the r elease button on the lever and pulling the lever upward to the transport position. 5. When the machine is standing still, activate the park brake by pushing the lever release button and pulling the lever upward.
20 OPERA TION IMPORT ANT INFORMA TION The mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles. CAUTION! Lead-acid batteries generate explosive gases.
21 OPERA TION Moving Machine By Hand When pushing or pulling the mower , engage the EZT bypass linkages. The EZT bypass linkages are located on the r ear of the frame, below the rear engine guar d. 1. Raise the deck into the highest cutting position. 2.
22 MAINTENANCE Maintenance Schedule The following is a list of maintenance procedur es that must be perfor med on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is 1) First change after 8-10 hours.
23 MAINTENANCE W ARNING ! Before performing any service or adjustment checklist • Engage the park brake. • Place the Blade-switch in the disengaged position. • T urn the ignition switch to OFF position and remove the key . • Make sure the blades and all moving parts have completely stopped.
24 MAINTENANCE Battery Y our mower is equipped with a maintenance free battery and does not need servicing. However , periodic charging of the battery with an automotive type batter y charger will extend its life. • Keep battery and ter minals clean.
25 MAINTENANCE Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: • The mower deck is disengaged. • The steering controls ar e in the outer , locked neutral position.
26 MAINTENANCE Anti-scalp Rollers Anti-scalp rollers ar e properly adjusted when they ar e just slightly off of the gr ound when the deck is at the desired cutting height in the operating position. Anti-scalp rollers then keep the deck in the proper position to help pr event scalping in most terrain conditions.
27 MAINTENANCE Adjusting the Mower Deck Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tir es are inflated to the corr ect pressur e. See T echnical Data / T ransmission. If tires are under or over inflated, the deck cannot be properly adjusted.
28 MAINTENANCE Cleaning Regular cleaning, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), befor e the debris sticks. Do not spray water on the top of the mower deck.
29 LUBRICA TION General Remove the ignition key to prevent unintentional movements during lubrication. When lubricating with an oil can, it must be filled with engine oil. When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.
30 LUBRICA TION Engine Oil Change NO TE: Change the engine oil when the engine is warm. Ref er to the engine owner’ s manual f or the correct replacement oil and filter change recommendations. W ARNING ! The engine drain plug is located close to the muffler .
31 TROUBLESHOOTING Problem / Cause Engine will not start Blade switch is engaged Steering controls ar e not locked in the neutral position Park brake is not activated Battery is dead Contamination in .
32 STORAGE Winter Storage The machine should be readied for storage at the end of the mowing season or if it will not be in use for more than 30 days. Fuel allowed to stand for long periods of time (30 days or more) can leave sticky r esidues that can plug the carburetor and disrupt engine function.
33 SCHEMA TIC.
34 TECHNICAL DA T A Engine Frame Manufacturer Kawasaki Cutting Width 46" / 117cm T ype FR651V Cutting Height 1.5" - 4" / 3.8 - 10.2 cm Power 21.5 1) Uncut Circle 0 Lubrication Pressur e with oil filter Number of Blades 2 Fuel Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Blade Length 22.
35 TECHNICAL DA T A Accessories Collection system Engine crankshaft bolt 75 ft/lb (100 Nm) Deck pulley bolts 75 ft/lb (100 Nm) Lug nuts 75 ft/lb (100 Nm) Blade bolt 60 ft/lb (81 Nm) Standard ¼" .
36 SERVICE JOURNAL Action Date, mtr reading, stamp, sign Delivery Service Charge the battery q Adjust the tire pr essure of all wheels to 15 PSI (1 bar) q Mount the steering controls in the normal pos.
37 SERVICE JOURNAL Action Date, mtr reading, stamp, sign Date, mtr reading, stamp, sign Date, mtr reading, stamp, sign Action Action 25-Hour Service Check the fuel pump’s air filter q Sharpen/Repla.
38 SERVICE JOURNAL Action Date, mtr reading, stamp, sign Action Date, mtr reading, stamp, sign 100-Hour Service Perfor m the 25-hour service q Perfor m the 50-hour service q Change the engine oil fil.
39 SERVICE JOURNAL Action Date, mtr reading, stamp, sign At Least Once Each Y ear Clean the engine’s cooling air intake (25 hours) q Replace the air cleaner’s foam pre-filter (300 hours) q Replac.
www .husqvarna.com 1 15 667527 Rev A 2013-1 1-15.
デバイスHusqvarna RZ46215の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna RZ46215をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna RZ46215の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna RZ46215の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna RZ46215で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna RZ46215を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna RZ46215の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna RZ46215に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna RZ46215デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
