HusqvarnaメーカーYTH145の使用説明書/サービス説明書
ページ先へ移動 of 52
YTH145 Owner ’ s Manual.
2 Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
3 CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/department.
4 T ABLE OF CONTENTS SAFETY RULES ............................................................ 2 PRODUCT SPECIFICATIONS ...................................... 3 CUSTOMER RESPONSIBILITIES ..................... 3, 16-19 ASSEMBLY ........................
5 CONTENTS OF HARDW ARE P ACK Parts packed separately in carton Parts Bag contents shown full size Parts bag contents not shown full size (4) Wheels (4) Adjusting Bars (4) Retainer Springs (double loop) (4) Clevis Pins (4) Washers 3/8 x 3/4 x 14 Ga.
ASSEMBL Y 6 Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.
ASSEMBL Y 7 FIG. 3 FIG. 2 TO ATTACH NOSE ROLLER (See Fig. 5) • Position brackets, 17/32 x 7/8 x 16 gauge washers, and nose roller between deck mounting brackets as shown. Be sure to position brackets on correct side, as shown. • Install 3/8-16 x 1 hex bolts and 3/8-16 lock nuts as shown.
ASSEMBL Y 8 INSTALL MULCHER PLATE (See Figs. 7 and 8) • Install two latch hooks to mulcher plate using screw, washer, lock washer, and weld nut as shown. NOTE: Pre-assemble weld nut to latch hook by inserting weld nut from the top with hook pointing down.
ASSEMBL Y 9 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual.
10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON.
OPERA TION 11 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference.
OPERA TION 12 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.
OPERA TION 13 TO OPERATE MOWER (See Fig. 11B) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. • Select desired height of cut.
OPERA TION 14 PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run- ning. To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time.
OPERA TION 15 MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN AFTER EACH USE. • The special mulching blade will recut the grass clip- pings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed.
16 CUST OMER RESPONSIBILITIES LUBRICATION CHART FRONT WHEEL BEARING ZERK FRONT WHEEL BEARING ZERK ATTACHMENT CLUTCH PIVOT(S) 1 ENGINE 3 SPINDLE ZERK SPINDLE ZERK 2 2 2 2 SAE 30 OR 10W30 MOTOR OIL GENE.
CUST OMER RESPONSIBILITIES 17 BLADE REMOVAL (See Fig. 15) • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and flat washer securing blade. • Install new or resharpened blade with trailing edge up towards deck as shown.
CUST OMER RESPONSIBILITIES 18 V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling.
CUST OMER RESPONSIBILITIES 19 FUEL FILTER CLAMP CLAMP FIG. 20 CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax.
SER VICE AND ADJUSTMENTS 20 CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place motion control lever in neutral (N) position. • Place attachment clutch in “DISENGAGED” position.
SER VICE AND ADJUSTMENTS 21 FIG. 25 FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25) IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.
SER VICE AND ADJUSTMENTS 22 FIG. 29 • Make sure attachment clutch and ignition switches are in “OFF” position. • Adjust the three nylon locknuts until space between clutch plate and rotor measures .012" at all three slot locations cut in the side of brake plate.
23 SER VICE AND ADJUSTMENTS FRONT WHEEL CAMBER The front wheel camber is not adjustable on your tractor. If damage has occurred to affect the front wheel camber, contact your nearest authorized service center/depart- ment. A B FRONT OF TRACTOR FIG.
24 SER VICE AND ADJUSTMENTS HOOD HEADLIGHT WIRE CONNECTOR TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
25 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark.
26 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
27 TROUBLESHOOTING POINTS Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department.
28 SER VICE NOTES.
29 TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 SCHEMATIC ALTERNATOR 14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) DIODE 28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED) CHARGING SYSTEM OUTPUT 9 AMP DC @ 3600 RPM BATTERY FUSE 30 AMP.
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 ELECTRICAL 30 28 29 26 24 42 43 44 44 25 41 19 20 19 20 40 33 32 31 30 50 22 21 70 12 12 11 10 8 2 1 27 46 47 16 D.
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 ELECTRICAL 31 KEY PART NO. NO. DESCRIPTION 1 532144925 Battery 12 Volt 25 AMP 2 874760412 Bolt Hex Hd 1/4-20unc X 3/4 8 532124886 Tray Battery 7.80 x 5.25 Blk 10 532145211 Bolt Btr Frt 1/2-20 x 7.
32 REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 CHASSIS AND ENCLOSURES 17 29 28 58 37 20 37 23 51 57 53 52 53 64 14 3 74 3 38 39 14 4 14 13 14 14 4 11 1 3 2 140 9 1.
33 REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 CHASSIS AND ENCLOSURES 1 532160392 Chassis Weldment 2 532140356 Drawbar, Stretch 3 817490612 Screw Thdrol 3/8-16x3/4 Ty-tt 4 819131216 Washer 13/32 x 3/4 x 16 Ga. 5 532155272 Bumper Hood/Dash 9 532156490 Dash Slkscr.
REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 DRIVE 34 29 28 32 61 30 52 61 32 37 97 16 73 103 102 94 3 19 16 146 98 53 35 55 36 62 35 36 22 34 16 1 77 96 147 71 18 .
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 DRIVE 35 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION NOTE: All component dimensions given in U.
36 REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 STEERING ASSEMBLY 5 5 7 7 4 3 43 6 43 8 18 19 22 20 27 62 23 11 40 66 29 25 5 8 10 40 40 68 68 11 11 15 8 6 46 46 8 .
37 REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 532124415 Wheel Steering 2 532137094 Axle Front Casting Machined 3.
REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 SEAT ASSEMBLY 38 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 532140839 Seat 2 532140551 Bracket Pivot Seat 8 720 3 874760616 Bolt Fin Hex 3/8-16unc X 1 4 819131610 Washer 13/32 X 1 X 10 Ga 5 532145006 Clip Push-In 6 873800600 Nut Hex w/Ins.
REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 DECALS 39 10 4 3 9 KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 532059192 Cap Valve Tire 2 532065139 Ste.
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 ENGINE 40 62 13 4 72 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 78 81 3 14 38 15 16 78 32 31 34 33 37 33 39 35 23.
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 ENGINE 41 1 532140310 Control Th/ch 23.5 LH. Flag 2 817720410 Screw Hex Thd Cut 1/4-20x5/8 T 3 - - - - - - - - Engine B&S Model No.
REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 MOWER DECK 42 15 14 12 128 13 11 10 9 8 16 68 30 31 32 33 54 133 55 56 17 21 5 134 135 136 116 117 119 118 137 140 1.
REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 MOWER DECK 43 68 532144200 V-Belt Mower 83 532120958 Washer Sintered 84 532156084 Keeper 'Belt Idler 85 872140620 Bolt Carriage 3/8-16 x 2-1/2 Gr.5 90 874760616 Bolt Fin Hex 3/8-16unc X 1 91 532132274 Bracket Asm Noseroller LH 92 873800600 Nut Lock Hex w/ins.
44 REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 MOWER LIFT 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 23 24 25 27 28 29 30 50 26 37 41 36 40 38 12 11 31 32 31.
45 REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 MOWER LIFT 1 532159460 Wire Asm Inner W/plunger 2 532159471 Shaft Asm Lift RH w/Inf 3 532105767 Pin Groove 1 500 Zi.
46 REP AIR P ARTS TRACT OR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 HYDRO GEAR TRANSAXLE - MODEL NUMBER 319-0650.
47 REP AIR P ARTS TRACTOR - MODEL NO. YTH145 (954140015A), PRODUCT NO. 954 14 00-15 HYDRO GEAR TRANSAXLE - MODEL NUMBER 319-0650 KEY PART NO. NO. DESCRIPTION 1 532142930 Housing, Lower 2 532142931 Ass.
48 SER VICE NOTES.
49 SER VICE NOTES.
50 15° MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. CUT OUT ON DOTTED LINES THIS IS A 15° SLOPE SIGHTING GUIDE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face.
W ARRANTY ST A TEMENT SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and w.
532166364 REV.1 10.05.98 SV Printed in U.S.A..
デバイスHusqvarna YTH145の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Husqvarna YTH145をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna YTH145の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna YTH145の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna YTH145で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna YTH145を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna YTH145の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna YTH145に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna YTH145デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。