HusqvarnaメーカーYTH2242 TFの使用説明書/サービス説明書
ページ先へ移動 of 44
YTH2242 TF Owner's Manual 532 44 15-91 Rev . 1 "This machine is approved by the EP A for E10 (10% ethanol) and lower fuel only . Do not use any fuel >E10 in this machine.
2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AIL URE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while backing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS K eys (2) Keys Slope Sheet AS SEMBL Y Y our new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. Fig. 1 Fig. 2 TO CHECK BA TTERY (See Fig. 1) • Lift hood to raised position.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW Y OUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. TO MOVE FORWARD AND BACK W ARD (See Fig. 7) The direction and speed of movement is controlled by the forward and reverse drive pedals.
11 Fig. 10 OPERA TION Fig. 11 TO TRANSPORT (See Fig. 11) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po- si tion. Free wheel control is located at the rear drawbar of tractor .
12 OPERA TION CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORT ANT : WHEN OPERA TING IN TEMPERA TURES BEL OW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP ENSURE GOOD COLD WEA THER ST ART ING.
13 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run- ning. T o ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time.
14 MAINTENANCE ➀ General Purpose Grease ➁ Refer to Maintenance “ENGINE” Section 01965 ➁ ENGINE ➀ FRONT WHEEL BEARING ZERK ➀ STEERING SECTOR GEAR TEETH ➀ FRONT WHEEL BEARING ZERK ➀ SPINDLE ZERK ➀ SPINDLE ZERK T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures .
15 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . Fig. 17 ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classification SG-SL.
17 MAINTENANCE CL AMP FUEL FIL TER Fig. 18 Fig. 19 • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out.
18 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key .
19 SERVICE AND ADJUSTMENTS E A M Q F B C C O H D D P Fig. 24 Fig. 25 • Install belt onto electric clutch pulley (M). Fig. 22 Fig. 23 • A TT ACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring.
20 SERVICE AND ADJUSTMENTS FRONT -TO-BACK ADJUSTMENT (See Figs. 29 & 30) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
21 SERVICE AND ADJUSTMENTS TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced.
22 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 36) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries.
23 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood.
24 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
25 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start.
26 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
27 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 SCHEMA TIC NO TES M FUSE ST ARTER SOLENOID BA TTER Y ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERS.
28 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V O.
29 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 18 64-91 Bo.
30 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 CHASSIS 214 178 204 207 208 25 15 211 209 210 212 175 177 182 176 176 176 205 150 130 130 5 176 181 137 165 202 234 14 234 1.
31 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 CHASSIS KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 2 532 41 22-82 Drawbar Lower 3 532 40 86-06 T rim, Husq. 4 532 40 50-12 Logo 5 532 40 87-00 Dash 6 532 11 04-52 Nut, Push 14 532 41 10-46 Hood 15 532 19 89-07 Lens LH 18 532 40 86-07 Grille/Lens Asm.
32 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 DRIVE 231 51 170 285 214 185 225 125 drive-tex_K46_pedal_73_r1 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 56 213 221 .
33 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 DRIVE 1 - - - - - - - - - T ransaxle, TUFFTORQ K46BT 2 532 12 35-83 K ey 15 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
34 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 ENGINE 1 84 12 11 41 42 85 29 SP ARK ARRESTER KIT 45 62 71 70 79 69 87 2 engine-te x_bs-2cyl_59 9 90 91 18 15 37 37 28 28 37.
35 KEY P ART NO . NO. DESCRIPTION 1 - - - - - - Engine Briggs Model No. 40H777-1421-B1 2 532 14 97-23 Muffler 9 532 19 43-20 Keeper Belt Engine 11 532 40 00-08 Clutch Electric 12 532 40 50-97 Pulley Engine 15 532 42 28-04 T ank F uel 18 532 43 02-17 Cap 20 532 42 35-02 Control Throttle 21 532 41 63-58 Screw #10 x .
36 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 STEERING ASSEMBL Y 21 19 60 16 28 28 13 22 64 45 51 63 57 63 6 55 5 13 13 53 8 9 9 8 8 7 7 62 4 35 59 58 50 50 70 65 68 69 6.
37 KEY P ART NO . NO . DESCRIPTION 1 532 41 64-80 Wheel, Steering 2 532 41 35-91 Axle Asm., F ront 4 532 40 30-89 Spindle Asm., LH 5 532 40 30-90 Spindle Asm.
38 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 SEA T AS SEMBL Y 1 532 42 40-71 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
39 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-vgt WHEELS AND TIRES KEY P ART NO .
40 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 MOWER DECK 3 4 5 8 9 10 12 13 14 18 19 22 23 25 26 27 28 29 30 31 33 34 40 41 42 43 44 45 46 48 49 50 51 52 53 54 56 1 2 6 7.
41 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 MOWER DECK KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE : All component dimensions given in U.
42 TRACTOR - MODEL NO . YTH2242 TF (96041022400), PRODUCT NO . 960 41 02-24 MOWER LIFT KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-30 Lever Asm.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
12.16.10 TH Printed in the U.S.A..
デバイスHusqvarna YTH2242 TFの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna YTH2242 TFをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna YTH2242 TFの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna YTH2242 TFの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna YTH2242 TFで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna YTH2242 TFを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna YTH2242 TFの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna YTH2242 TFに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna YTH2242 TFデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
