HusqvarnaメーカーYTH24V48LSの使用説明書/サービス説明書
ページ先へ移動 of 44
YTH24V48LS Owner's Manual 532 44 03-88 07002.
2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AILURE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH.
3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing.
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBL Y ....................................
5 UNAS SEMBLED P ARTS Y our new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. ADJUST SEA T (See Fig. 2) • Sit in seat. • Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.
6 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled.
7 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only.
8 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference.
9 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs.
10 OPERA TION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. TO MOVE FORWARD AND BACK WARD (See Fig. 7) The direction and speed of movement is controlled by the forward and reverse drive pedals.
11 Fig. 10 OPERA TION Fig. 12 Fig. 11 TO TRANSPORT (See Figs. 3 and 12) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po- si tion. Free wheel control is located at the rear drawbar of tractor .
12 OPERA TION CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORT ANT : WHEN OPERA TING IN TEMPERA TURES BEL OW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP ENSURE GOOD COLD WEA THER ST ART ING.
13 Fig. 14 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time.
14 MAINTENANCE T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil.
15 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed.
16 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from wear . ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classification SG-SL.
17 MAINTENANCE CL AMP FUEL FIL TER Fig. 19 IN-LINE FUEL FIL TER (See Fig. 19) The fuel filter should be replaced once each season. If fuel filter becomes clogged, ob struct ing fuel flow to car bu re tor , re place ment is re quired. • With engine cool, remove filter and plug fuel line sec- tions.
18 WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key .
19 SERVICE AND ADJUSTMENTS Fig. 28 Fig. 29 • Install belt onto electric clutch pulley (M). Fig. 26 Fig. 27 • A TT ACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring.
20 SERVICE AND ADJUSTMENTS FRONT - TO-BACK ADJUSTMENT (See Figs. 32 & 33) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
21 SERVICE AND ADJUSTMENTS TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced.
22 Fig. 37 Fig. 38 RE T AIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONL Y) AXLE COVER TO REMOVE WHEEL (See Fig. 38) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).
23 TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 39) WARNING : Lead-acid batteries gen er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged.
24 TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.
25 Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING : Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.
26 PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug.
27 PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department.
28 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO .
29 NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PED AL UP) REVERSE SWITCH (NO T IN REVERSE) SEA T SWITCH (NO T OCCUPIED) SHORTING CONNECT OR CHASSIS HARNESS IGNITION UNIT HOU.
30 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 16 42 T15S 29 With 12V Outlet Option 59 103.
31 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 ELECTRICAL KEY P ART NO . NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 18 64-91 Bo.
32 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 CHASSIS 14 130 130 130 203 208 18 15 25 207 206 3 214 204 297 191 chassis-tex_GT HUSQ II_17 130 182 176 176 175 150 130 177 .
33 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 CHASSIS KEY P ART NO . NO . DESCRIPTION 2 532 41 22-82 Drawbar Lower 3 532 43 97-52 Logo 5 532 43 74-70 Dash 14 532 43 97-25.
34 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 DRIVE 225 125 drive-tex_K46_pedal_70_r2 56 70 74 220 74 64 188 161 35 184 167 160 42 159 221 186 189 49 187 50 51 52 51 190 .
35 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - - - T ransaxle, TUFF TORQ K46 CR 2 532 12 35-83 Key 15 819 13 13-16 W asher 13/32 x 13/16 x 16 Ga.
36 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 ENGINE 1 92 12 11 41 42 85 9 29 SP ARK ARRESTER KIT 92 45 90 22 62 70 71 86 69 87 2 engine-tex_Ka wa-2cyl_10 18 15 91 21 20 116 14 37 28 28 37 117 KEY P ART NO . NO . DESCRIPTION KEY P ART NO .
37 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 SEA T ASSEMBL Y 2 6 1 40 10 37 37 21 21 3 41 7 8 7 8 8 8 seat-tex_6.5SL_2 44 43 1 532 42 40-71 Seat 2 532 18 01-66 Bracket Pivot F ender 3 532 14 06-75 Strap, Asm F ender 6 873 80 06-00 Nut, Lock w/Ins.
38 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 STEERING ASSEMBL Y 55 35 19 63 60 59 58 67 54 67 78 66 54 65 61 55 2 Steering-tex_LEGND2_39_r1 6 5 13 13 53 8 62 4 50 50 70 .
39 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 64-80 Wheel, Steering 2 532 19 59-68 Axle Asm.
40 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 MOWER DECK 3 4 5 8 9 10 12 13 14 18 19 22 23 16 33 27 28 29 30 31 32 33 34 35 37 38 39 41 42 44 45 46 48 49 50 51 52 53 54 5.
41 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE : All component dimensions given in U.
42 TRACTOR - MODEL NO . YTH24V48LS (96043011600), PRODUCT NO . 960 43 01-16 MOWER LIFT LIFTTEX? 2 532 42 20-27 Shaft Asm.
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face.
11.09.10 BAD Printed in the U.S.A..
デバイスHusqvarna YTH24V48LSの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Husqvarna YTH24V48LSをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはHusqvarna YTH24V48LSの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Husqvarna YTH24V48LSの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Husqvarna YTH24V48LSで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Husqvarna YTH24V48LSを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はHusqvarna YTH24V48LSの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Husqvarna YTH24V48LSに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちHusqvarna YTH24V48LSデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
