IBMメーカーATA-3の使用説明書/サービス説明書
ページ先へ移動 of 92
Deskstar Enhanced I D E (A T A-3) Hard Disk Dr ive U ser's Guide OP T IONS by I B M.
Note: If you are using this product in the United States, Canada, or Puerto Rico, be sure to read the Deskstar Enhanced IDE (ATA-3) Hard Disk Drive User's Guide Supplement for warranty information and jumper setting information for your hard disk drive.
Contents Safety: Read First . . . . . . . . . . . . . . . . . . . . . . . v About This Book ........................ v i Part 1: Quick Installation Guide ................................................ 1-1 Part 2: Installation Guide . . . . . . . . .
Part 3: Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Appendix A. Safety Information . . . . . . . . . . . . . . 3-1 Appendix B. Help and Service Information ........ 3-11 Step 1.
Safety: Read First CAUTION: Read the Safety Information in Appendix A, page 3-1, before installing this product. DO NOT print this page— replace with World Wide 'Read First' translations.
About This Book This book contains instructions for installing, setting up, and using your Deskstar Hard Disk Drive. The manual is divided into the following parts: Part 1: Abbreviated installation in.
Part 1: Quick Installation Guide Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 1 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (German) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 3 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (French) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 5 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (Spanish) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 7 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (Japanese) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 9 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (Italian) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 11 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
Quick Installation (Brazilian Portuguese) Part 1 contains the Deskstar Hard Disk Drive installation instructions in abbreviated form. If you are familiar with IDE products and experienced in installing options, use these instructions to quickly install your IDE drive.
Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority. The positions are: Master Slave Cable Select Slave Present Use the .
Step 4. Installing the Drive in the Drive Bay Mount the hard disk drive in the drive bay using the four mounting screws provided with the drive. For proper grounding be sure to use all four screws. Step 5. Connecting the Drive and the Cables Connect the drive to an available 40-pin connector on the IDE interface cable.
The largest partition size that you can create under the DOS, Windows 95, Windows 3.x, and OS/2 operating systems that use 16-bit file allocation table (FAT) conventions is approximately 2.14 GB. 13 When you are installing a drive larger than 2.14 GB, you must create more than one partition to use the full capacity of your drive.
Disk Manager will display the number and types of drives found on your system and ask you if the list is correct. Follow the onscreen prompts. 5. Disk Manager will then display the drive capacity partitions selected for your system and ask if you wish to continue.
Correcting BIOS Limitations and Partitioning Using Disk Manager Your BIOS might contain limitations that can cause operational failures when you install one of the new and larger hard disk drives. See the documentation that comes with your IBM computer to install your hard disk drive, and to configure your system.
Partitioning and Formatting Using Disk Manager The Disk Manager software contains programs that can partition, format, and prepare your drive for the installation of an operating system. The following procedure prepares your drive for use in both IBM and Non-IBM computers.
1-50 Deskstar Hard Disk Drive User’s Guide.
Part 2: Installation Guide Product Description The Deskstar Hard Disk Drive is a 3.5-inch slimline (1-inch high) drive. It can only be installed in computers that use the AT attachment/integrated drive electronics (ATA/IDE) architecture.
Before You Begin Read the following information before you start your installation. The installer of the drive will have to complete the following steps: Set the jumper setting on the drive (and possibly make changes to installed drives) Physically install the drive in a 3.
Mounting brackets and tools Most computers have 3.5-inch and 5.25-inch drive bays. The hard disk drive you are installing is designed for a 3.5-inch bay, but it can be adapted to a 5.25-inch bay. Common bay dimensions are: – 3.5-inch—10.2 cm x 15.
you are installing. Some devices, such as a high speed tape drive, do not operate properly when installed on the same port with a hard disk drive. The primary drive must be configured as master and installed on the primary IDE port. You must install the operating system on the primary drive, normally C:.
file uses one full cluster. The following table shows how the cluster size is incremented as the partition size increases. 16 These examples illustrate the effect of cluster size on hard disk space allocation. If you create a 2.14 GB partition, each disk cluster is 32 KB.
Backup Considerations If you are replacing an installed hard disk drive, make a backup copy of the data from the drive that you are replacing. If you do not know how to back up your hard disk drive, see the documentation that comes with your operating system.
Handling Precautions To avoid damage to your hard disk drive during installation. Do not open the antistatic bag until you are ready to install the drive. Static electricity can damage the drive and other computer components. Before handling the drive, ground yourself by touching an unpainted surface on the computer.
3. If you must put the drive down, place the antistatic bag on a flat padded surface, such as a magazine, and place the drive on the bag with the component side facing up. Step 3. Setting the Configuration Jumpers Your drive has four configuration positions that determine the data transmission priority.
For information on jumper positions for your drive, see the Deskstar Enhanced IDE (ATA-3) Hard Disk Drive User’s Guide Supplement . What to Do Next If you are installing the drive in a 3.5-inch bay, go to “Step 5. Mounting the Drive in the Bay.” If you are installing the drive in a 5.
Step 6. Attaching the Cables to the Drive Use the following procedure to attach the cables. Pin 40 Pin 1 1. Locate a free device connector on the IDE interface cable in your computer. The illustration shows an interface cable with three connectors and two attached devices.
If all power cables are in use, purchase a dc Y-connector (available at many electronic stores) and split a connection to provide power for more devices. Step 7. Completing the Installation To complete the hardware section of the drive installation: 1.
“Correcting BIOS Limitations and Partitioning Using Disk Manager” on page 2-15. Using Your Operating System for Partitioning This section contains instructions about partitioning and formatting your hard disk drive for the DOS, Windows, and OS/2 operating systems.
Installing a Secondary Drive for DOS or Windows Use FDISK and FORMAT to prepare the drive if you are using any of the following: DOS Windows 3.1x Windows for Workgroups 3.1x Windows 95 When you use FDISK you must make decisions about the number and types of partitions that you want to create on the drive.
Installing a Primary Drive using OS/2 If the new hard disk drive will contain your operating system (drive C), use this procedure to prepare the drive and install your operating system: 1. Insert the OS/2 Installation Diskette into drive A. 2. Turn on your computer.
User’s Guide Supplement will list your drive's jumper settings.) c. Replace the computer cover and recheck all external cables. 3. Restart the computer and check the drive size reported by the configuration-setup program. If the drive is not detected, go to Appendix B, “Help and Service Information” on page 3-11.
Normally, drives 1 and 2 are connected to the primary IDE port and drives 3 and 4 are connected to the secondary IDE port. If you have two IDE ports, drives 1 and 3 are the master devices and drives 2 and 4 are the slave devices. If you have one IDE controller, drive 1 is the master device and drive 2 is the slave device.
6. Follow the instructions on the screens to complete the drive partitioning process. Install your operating system as described in the Disk Manager Online Manual .
FileCopy FileCopy is a program that runs under DOS and copies all files from one drive letter to another. You can use FileCopy with Disk Manager to simplify the task of adding a new hard disk drive that will replace your startup drive and will contain your operating system.
Problem Solving You might be able to solve the problem yourself. Before calling IBM, you might want to try some or all of the following troubleshooting procedures. If your computer does not operate correctly, or the drive fails to spin up, be sure that the colored line on the drive end of the cable is closest to the dc power connector.
If your computer does not restart and none of the devices work, the interface cable connector might be connected backwards. To check the connection: 1. Turn off the computer. 2. Disconnect the IDE cable from the drive. 3. Verify that the colored wire is connected to pin 1 on the drive connector and is the closest wire to the 4-pin power connector.
Part 3: Appendixes Appendix A. Safety Information To Disconnect: DO NOT print this page— replace with National Safety Information. Copyright IBM Corp.
DO NOT print this page—replace with National Safety Information. 3-2 Deskstar Hard Disk Drive User’s Guide.
DO NOT print this page— replace with National Safety Information. Part 3: Appendixes 3-3.
DO NOT print this page— replace with National Safety Information. 3-4 Deskstar Hard Disk Drive User’s Guide.
DO NOT print this page— replace with National Safety Information. Part 3: Appendixes 3-5.
To Connect: DO NOT print this page— replace with National Safety Information. 3-6 Deskstar Hard Disk Drive User’s Guide.
DO NOT print this page— replace with National Safety Information. Part 3: Appendixes 3-7.
DO NOT print this page— replace with National Safety Information. 3-8 Deskstar Hard Disk Drive User’s Guide.
DO NOT print this page— replace with National Safety Information. Part 3: Appendixes 3-9.
DO NOT print this page— replace with National Safety Information. 3-10 Deskstar Hard Disk Drive User’s Guide.
Appendix B. Help and Service Information Before calling IBM technical support, try to solve the problem yourself by using the information in “Problem Solving” on page 2-19. If you are unable to solve the problem yourself, this section contains information on how to reach your IBM technical support representative.
Computer and BIOS Manufacturers Use the following table for computer manufacturer information. For manufacturers not in the table, contact your IBM reseller. Use the following table for BIOS manufacturer information. For manufacturers not in the table, contact your IBM reseller.
Hard Disk Drive Manufacturers Use the following table for disk manufacturer information, as needed. For manufacturers not in the table, contact your IBM reseller. Manufacturer Telephone BBS Fax Internet Address IBM Corporation (U.S.A.) 1-800-772-2227 1-919-517-0001 1-800-426-3395 http://www.
Appendix C. Notices This appendix contains the product notices and trademarks information. Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates.
.
IBM Part Number: 4304439 Printed in U.S.A. 43 4439.
デバイスIBM ATA-3の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
IBM ATA-3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM ATA-3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM ATA-3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM ATA-3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM ATA-3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM ATA-3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM ATA-3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM ATA-3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。