IBMメーカーE74Mの使用説明書/サービス説明書
ページ先へ移動 of 37
i Edition 1 This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein, these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or programs(s) at any time.
ii Packing List The product package should include the following items: 1. Monitor 2. Owner ’s Manual 3. Power Cord 4. Diskette 5. Audio Cable 6. Mic Cable.
iii T able of Contents Introduction Features .................................................................................................... A1 Precautions Workplace Perparation ....................................................................
A1 Introduction Thank you for purchasing a high resolution monitor . It will give you high resolution performance and convenient reliable operation in a variety of video operating modes.
A2 Precautions Danger T o avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet.
A3 Rest T ake regular breaks. V ary your posture, and stand up and stretch occasionally as prolonged use of computer workstations can be tiring. Back Y ou should sit back in the chair and use the back rest. Hands Use a light touch on the keyboard, keeping your hands and fingers relaxed.
A4 Power Source: 1. Make sure the power cord is the correct type that required in your area. 2. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area ( No user adjustment is required.
A5 Figure 1 shows the signal cable connections from the monitor to the Video Graphics Array (VGA) port typical in an IBM PC or PC compatible. This also applies to any graphics video card for PC-CAD or workstation that has a 15 pin high density (3 row) D-Sub connector .
A6 Location and Function of Controls Front View Rear View MIC. OUT AUDIO IN AC Power Socket D-Sub Signal Cable ID Label Audio IN Mic Out Front Panel Controls Left Side Jacks.
Control Panel Function Front Panel Controls A7 OSD Select/ Adjustment Control Use this buttons selecting (highlighting) an OSD icon to be adjusted. It is also used for selecting the level of the selected item to be adjusted. Use this button to start/enter and exit from the On Screen Display .
Left Side Jacks Rear Panel Jacks Microphone Operation On the left side there is a MIC (Microphone) jack. By plugging a microphone in here, it may reduce the long length of cable needed to reach the PC's sound card.
On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position, and operating parameters of the monitor is quick and easy with the On Screen Display Control system, using only the ENTER button and Adjustment Control buttons.
On Screen Display(OSD) Selection and Adjustment Y ou were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items that are shown on the Menu. A10 T o move picture image left and right.
A11 OSD U 85% PINCUSHION BALANCE MAIN : ADJ: T o correct the balance of both sides bowling. ◀ Curvature of the sides to the right. ▶ Curvature of the sides to the left. This control adjusts for a skewing of the screen image. ◀ T ilts the screen image rightward.
A12 COLOR CONTROL SELECT: NEXT: OSD U USER CURVE 9300K 6550K () T o select color temperature 9300K/ 6550K/ USER and CURVE. Select the desired color temperature or select user to set your own color levels. Allow for specific adjustments to Red, Green and Blue(R/G/B).
A13 T o choose the language in which the control names are displayed. OSD Menus are available in five language : English, German, French, Spanish and Italian.
Sound Selection and Adjustment ( ) Y ou were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items that are shown on the main Menu. A14 Raises or lowers audio level.
A15 Video Memory Modes The monitor has 20 memory locations for display modes, 10 of which are factory preset to popular video modes. Display Modes ( Resolution) Display Modes (Resolution) Horizontal Frequency (kHz) V ertical Frequency (kHz) User Modes Modes 1 1-20 are empty and can accept new video data.
Energy Saving Design This monitor complies with the EP A's Energy Star program, which is a program designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during time of non-use.
A17 Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an AGAR.
T roubleshooting Self diagnostics message. ■ The signal cable is not connected, or is loose. Check and secure the connection. OUT OF FREQUENCY message appears. ■ The frequency of the signal from the video card is outside the operating range of the monitor .
A19 Further help If you are unable to correct the problem yourself, you may seek further help as follows: Call IBM HELPCENTER. In the USA call 1-800-772-2227 In Canada call 1-800-565-3344 In other countries, contact your dealer , retailer , or other IBM authorized servicer .
A20 Service Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when : ■ The power cord or plug is damaged or frayed. ■ Liquid has been spilled into the monitor . ■ The monitor has been exposed to rain or water .
Specifications Sync Signal T ypes Signal Connector Pin Assignment Note :No. 5 Pin have to ground on the PC side. A21 15 6 10 11 15 (N.C : No Connection) T ype H.
A22 Specifications Picture tube ■ 17 inches (15.9 inches viewable) FST ■ 90 degree deflection ■ 0.27 mm dot pitch, Non-glare, AGAR Sync Input ■ Horizontal Frequency : 30 - 70kHz (Automatic) .
Statement of W arranty Part 1 - General T erms This Statement of W arranty includes Part 1 - General T erms and Part 2 - Country-unique T erms. The terms of Part 2 may r eplace or modify those of Part 1.
Any technical or other support provided for a Machine under warranty, such as assistance via telephone with “how-to” questions and those regarding Machine set-up and installation, will be provided WITHOUT W ARRANTIES OF ANY KIND. W arranty Service T o obtain warranty service for the Machine, contact your reseller or IBM.
Limitation of Liability Circumstances may arise where, because of a default on IBM’ s part or other liability , you are entitled to recover damages from IBM.
NEW ZEALAND: The IBM W arranty for Machines: The following paragraph is added to this Section: The warranties specified in this Section are in addition to any rights you may have under the Consumer Guarantees Act 1993 or other legislation which cannot be excluded or limited.
The following paragraphs are added to this Section: The minimum warranty period for Machines is six months. In case IBM or your reseller are unable to repair an IBM Machine, you can alternatively ask .
SOUTH AFRICA, NAMIBIA, BOTSW ANA, LESOTHO AND SW AZILAND: Limitation of Liability: The following is added to this Section: IBM’ s entire liability to you for actual damages arising in all situations.
A29 Y our IBM Monitor Installation Diskette includes translations of IBM’s Statement of W arranty in the following languages. Worldwide Statement of W arranty (Except T urkiye, U.S, Puerto Rico and Canada . Arabic Z1255697.ara.html Brazilian Portuguese Z1255697.
Compliances Federal Communications Commission(FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Power Cord: For your safety , IBM provides a power cord with a grounded attachment plug to use with this IBM product. T o avoid electrical shock, always use the power cord and plug with a properly grounded power outlet.
MPR II This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPR II) for very low frequency (VLF) and extremely low frequency (ELF).
Hinweis f ü r die Europ ä ische Union (EU) Dieses Ger ä t hat in T ests die Grenzwerte eingehalten, die gem äß CISPR 22/Europ ä ische Norm EN 55022 f ü r informationstechnische Ger ä te der Klasse B festgeschrieben sind.
Per ridurre la possibilit à di causare interferenza alle comunicazioni radio e televisive ed ad altre apparecchiature elettriche o elettroniche, occorre usare cavi e connettori opportunamente schermati e messi a terra. T ali cavi e connettori sono disponibili presso i rivenditori autorizzati IBM.
デバイスIBM E74Mの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM E74Mをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM E74Mの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM E74Mの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM E74Mで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM E74Mを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM E74Mの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM E74Mに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM E74Mデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
