IBM Partner Pavilionメーカー8137の使用説明書/サービス説明書
ページ先へ移動 of 64
Us er Gu i d e Ty p e s 81 31 , 81 3 7 , 81 3 8 Ty p e s 81 2 2 , 81 2 3 , 81 2 4 .
.
Us er Gu i d e Ty p e s 81 31 , 81 3 7 , 81 3 8 Ty p e s 81 2 2 , 81 2 3 , 81 2 4 .
Note Before using this information and the pr oduct it supports, be sure to read the “Important safety information” on page v and Appendix D, “Notices,” on page 43. Third Edition (May 2006) © Copyright International Business Machines Corporation 2006.
Contents Important safety information . . . . . .v Conditions that requir e immediate action . . . . .v General safety guidelines . . . . . . . . . .v i Service . . . . . . . . . . . . . . .v i Power cords and power adapters . . . . . . vii Extension cords and r elated devices .
iv User Guide.
Important safety information Note Please read important safety information first. This information can help you safely use your ThinkCentre ® or ThinkPad ® personal computer .
unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. See “Information resources” on page xiii. v Power cords, plugs, power adapters, extension cor ds, surge pr otectors, or power supplies that are cracked, br oken or damaged.
Danger Hazardous moving parts. Keep fingers and other body parts away . Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover . Power cords and power adapters Use only the power cords and power adapters supplied by the pr oduct manufacturer .
product. Never overload these devices. If power strips ar e used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requir ements, and input ratings.
Heat and product ventilation Computers generate heat when turned on and when batteries are char ging. Notebook PCs can generate a significant amount of heat due to their compact size.
v Check CD/DVD discs for cracks before each use. Do not use cracked or damaged discs Additional safety information Danger Electrical current from power , telephone, and communication cables is hazardous.
Modem safety information Caution To reduce the risk of fire, use only No. 26 AW G or larger telecommunication line cord. To reduce the risk of fir e, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, curr ent, and energy levels ar e present inside any component that has this label attached. There ar e no serviceable parts inside these components.
Overview Thank you for selecting this computer . Y our computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change. Adding hardwar e options to your computer is an easy way to increase its capabilities.
xiv User Guide.
Chapter 1. Installing options This chapter provides an intr oduction to the features and options that ar e available for your computer . Yo u can expand the capabilities of your computer by adding memory , adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option.
Memory v Support for four double data rate 2 (DDR2) dual inline memory modules (DIMM) v 512 KB flash memory for system programs Internal drives v 3.5-inch, slim, 1.
Expansion v Four drive bays v Tw o standard PCI adapter connectors v One PCI Express (x1) adapter connector v One PCI Express (x16) graphics adapter connector (some models) Power v 230 W power supply .
Specifications This section lists the physical specifications for your computer . Dimensions Height: 432 mm (17.0 in.) W idth: 178 mm (7.0 in.) Depth: 450 mm (17.
A vailable options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and dig.
Handling static-sensitive devices Static electricity , although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instr ucted to do so.
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer . Note: Not all computer models will have the following connectors.
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer . 1 Diagnostic LEDs 11 Ethernet connector .
Connector Description Audio line in connector Used to receive audio signals fr om an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line out connector of the device and the audio line in connector of the computer .
Removing the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices” on page 6 before r emoving the cover . To remove the cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn of f all attached devices and the computer .
Locating components The following illustration will help you locate the various components in your computer . 1 Optical drive 2 Memory modules 3 Power supply 4 PCI adapter connector 5 PCI adapter card 6 System board 7 Hard disk drive 8 Internal speaker 9 Diskette drive Chapter 1.
Identifying parts on the system board The system board (sometimes called the planar or motherboard ) is the main cir cuit board in your computer . It pr ovides basic computer functions and supports a variety of devices that are factory-installed or that you can install later .
Installing memory Y our computer has four connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 4.0 GB of system memory . When installing DDR2 type memory modules, the following rules apply: v Use 1.8 V, 240-pin DDR2 synchronous dynamic random access memory (SDRAM).
Installing adapters This section provides information and instr uctions for installing and removing adapters. Y our computer has two expansion connectors for PCI adapters, one for a PCI Express (x1) adapter , and one for a PCI Expr ess (x16) adapter .
What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 25. Installing internal drives This section provides information and instr uctions for installing and removing internal drives.
The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) v Optical drive such as CD drive or DVD drive (preinstalled in some models) v 5.
Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the cover . See “Removing the cover” on page 10. 2. Remove the front bezel by pr essing downward on the plastic tabs 1 and pulling the bezel as shown.
5. If you are installing any type of drive other than a serial ATA hard disk drive, make sure the drive that you ar e installing is set correctly as either a master or a slave device. Note: A serial ATA hard disk drive does not need to be set as either a master or a slave device.
9. Install the front bezel by aligning the plastic tabs on the bottom of the bezel with the corresponding holes in chassis and pr ess it onto the chassis until it snaps into position. 10. Continue at “Connecting drives.” Connecting drives The steps to connect a drive are dif ferent depending on the type of drive.
Connecting an additional optical drive, or parallel ATA hard disk drive 1. Locate the extra connector on the three-connector signal cable that is attached to the PATA IDE connector on the system board. See “Identifying parts on the system board” on page 12.
Installing security features To help prevent har dware theft and unauthorized access to your computer , several security lock options are available. The following sections will help you identify and install the various types of locks that might be available for your computer .
Padlock Y our computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. 22 User Guide.
Integrated cable lock W ith an integrated cable lock (sometimes r eferred to as a Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixtur e. This lock also secures the computer cover . The cable lock attaches to a security slot at the rear of your computer and is operated with a key .
configuration information (including passwords) ar e lost. An error message is displayed when you turn on the computer . Refer to “Lithium battery notice” on page x for information about replacing and disposing of the battery . To change the battery: 1.
5. Move the jumper from the standar d position (pins 1 and 2) to the maintenance or configure position (pins 2 and 3). 6. Replace the cover and connect the power cord. See “Replacing the cover and connecting the cables.” 7. Restart the computer , leave it on for approximately ten seconds.
26 User Guide.
Chapter 2. Using the Setup Utility program The Setup Utility program is stor ed in the electrically erasable programmable read-only memory (EEPROM) of your computer . The Setup Utility pr ogram is used to view and change the configuration settings of your computer , regar dless of which operating system you are using.
Administrator Password Setting an Administrator Password deters unauthorized persons fr om changing configuration settings. If you are r esponsible for maintaining the settings of several computers, you might want to set an Administrator Password.
Selecting a startup device If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following pr ocedures to select a startup device. Selecting a temporary startup device Use this procedur e to startup from any boot device.
30 User Guide.
Appendix A. Updating system programs This appendix contains information about updating system programs and how to recover fr om a POST/BIOS update failure. System programs System programs ar e the basic layer of software that is built into your computer .
1. From your br owser , type http://www .lenovo.com/think/support in the address field and pr ess Enter . 2. Locate the Downloadable files for your machine type as follows: a. Under Use Quick path, type your machine type and click Go . b. Click Continue .
Appendix B. Cleaning the mouse This appendix provides instr uctions on how to clean your mouse. The procedure will be differ ent depending on which type of mouse you have. Cleaning an optical mouse If you experience some problems with your optical mouse, check the following: 1.
3. Place your hand over the retainer ring and ball 2 , and then turn the mouse over , top side up, so that the retainer ring and ball fall out into your hand. 4. W ash the ball in warm, soapy water then dry it with a clean cloth. Blow air carefully into the ball cage 4 to dislodge dust and lint.
Appendix C. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Y our modem is automatically in Command Mode until you dial a number and establish a connection.
Command Function H1 Force modem of f-hook (make busy) Note: H1 command is not supported for Italy I_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firm.
Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 T urn on CD when remote carrier is present &D_ &D0 Modem ignores the DTR signal &D1 Mode.
Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active pr ofile as Profile 0 &W1 Stores the active pr ofile as Profile 1 %E_ %E0 Disable auto-retrain %E1 Ena.
Fax Class 1 commands +F AE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n T ransmit data with HDLC framing +FTM=n T ransmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling.
Attention Switzerland User: If your Swisscom phone line does not have T axsignal switched OFF , modem function may be impaired. The impairment may be r esolved by a filter with the following specifications: T elekom PTT SCR-BE T aximpulssperrfilter -12kHz PTT Art.
42 User Guide.
Appendix D. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area.
vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation.
Index A adapters installing 14 peripheral component interconnect (PCI) 5 slots 14 audio line in connector 9 audio line out connector 9 audio, subsystem 2 B battery location 12 boot-block recovery 32 C.
S security features 3, 21 hard disk drive 27 integrated cable lock 22, 23 security profile by device 28 serial connector 9 Setup Utility program 27 system board connectors 12 identifying parts 12 loca.
.
Part Number: 39J7710 Printed in USA (1P) P/N: 39J7710.
デバイスIBM Partner Pavilion 8137の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM Partner Pavilion 8137をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM Partner Pavilion 8137の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM Partner Pavilion 8137の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM Partner Pavilion 8137で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM Partner Pavilion 8137を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM Partner Pavilion 8137の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM Partner Pavilion 8137に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM Partner Pavilion 8137デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
