IBMメーカーRS/6000 7043 43P Seriesの使用説明書/サービス説明書
ページ先へ移動 of 26
Su p p l e m e nt t o th e RS / 6000 7 043 43P Se ri es ( S A38-05 1 1 an d S A38-05 1 2 ) S e rvi c e G ui d e a n d U s e r’s G ui d e SN32-9080-01 IBM.
Second Edition (December 2000) Before using this information and the product it supports, read the information in “Appendix. Notices” on page 15. © International Business Machines Corporation 2000.
Contents About This Book ....................... v ISO 9000 .......................... v Online Publications ....................... v Related Publications ...................... v T rademarks ......................... v Chapter 1. 7043–140 and 7043–150 Fansink Removal and Replacement Procedures .
iv Supplement to the Service Guide and User’s Guide.
About This Book This supplement provides updates to the following publications: v RS/6000 7043 43P Series User’s Guide , SA38-051 1 v RS/6000 7043 43P Series Service Guide , SA38-0512 ISO 9000 ISO 9000 registered quality systems were used in the development and manufacturing of this product.
vi Supplement to the Service Guide and User’s Guide.
Chapter 1. 7043–140 and 7043–150 Fansink Removal and Replacement Procedures This chapter provides information on replacing defective 7043–140 and 7043–150 fansinks without having to replace the entire system board.
T able 2. Fansink numbers by System Board Assembly and FRU Numbers (continued). Machine T ype FRU Part Numbers System Board Assembly Part Numbers Fansink Number 7043–150 375MHZ New V ersion System B.
4. T o remove the disk drive bracket, refer to the ″ Removing Internal Drive ″ section of the RS/6000 7043–43P Series Service Guide . Carefully place the bracket assembly on top of the power supply (leave the hard files plugged in). Note: Disconect temporarily any PCI Adapter Card installed in slot 5 in order to remove the disk drive bracket.
Replacement 1. If you are replacing a fansink 09P1 125, install the new component by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position. OR If you are replacing a fansink 09P1 126, first remove the paper pull tab to expose the thermal grease underneath.
5. Locate and unplug the fan and disconnect the fansink assembly power cable from the CPU fansink connector (J26). Note: There are two possible fansink connections for this system board: right-angle finger tabs, and wire springs.
Replacement 1. If you are replacing a fansink 09P1 126, first remove the paper pull tab to expose the thermal grease underneath. Install the new fansink by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position.
Chapter 2. 7043–150 System Features This chapter contains information specific to both the 250MHz and 375MHz options for the Model 150, and applies to the RS/6000 7043 43P Series User’s Guide and the RS/6000 7043 43P Series Service Guide. All other information is consistent with the system books.
Keyboard and Mouse v Standard: 101–Key Enhanced keyboard v Optional: 101/102 or 106–Key Enhanced Keyboard v Standard: 3-button mouse Front-Panel Display v 4-digit LED diagnostics display Input/Out.
Setting the SCSI Security Jumpers Note: Carefully read and follow the safety guidelines detailed in the corresponding section of the RS/6000 7043 43P Series User’s Guide , SA38-051 1. T o increase system unit security , the external SCSI connector can be disabled by changing jumpers inside the system unit.
System Board Locations for Model 150 B1 Battery connector J1 W akeup-on-LAN jumper J2 5x5 Auxiliary 5v connector J3 Audio input connector J4 Internal SCSI connector #2 J5 CD-ROM audio connector J6 CD-.
J13 Audio output connector J15 Remote Power-up Jumper J16 Diskette drive connector J17 Microphone jack J18 Reset Connector J19 Memory Connector 3 J20 Power-on Password jumper J22 Headphone jack J23 Se.
System Board, Cables, and Accessories 12 Supplement to the Service Guide and User’s Guide.
Index Number FRU Number Units Per Assy Description 1 09P0168 1 System Board (250 MHz) 2 27F4212 6 Screw 3 39H8697 1 Hex Standoff 4 19L1808 1-4 64MB DIMM 19L1809 1-4 128MB DIMM 29L3302 1-4 256MB DIMM 5.
14 Supplement to the Service Guide and User’s Guide.
Appendix. Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer’s representative for information on the products and services currently available in your area.
16 Supplement to the Service Guide and User’s Guide.
Reader’s Comments — We’d Like to Hear From Y ou Supplement to the RS/6000 7043 43P Series Service Guide and User’s Guide Order Number: SN32–9080–01 Overall how satisfied are you with the i.
Fold and T ape Fold and T ape Please do not Staple Please do not Staple Fold and T ape Fold and T ape Information Development Department H6DS-9561 11400 Burnet Road Austin, TX 78758-3493 Cut or Fold A.
.
IBMR Part Number: 09P2506 Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber . December 2000 SN32-9080-01 (1P) P/N: 09P2506.
デバイスIBM RS/6000 7043 43P Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM RS/6000 7043 43P Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM RS/6000 7043 43P Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM RS/6000 7043 43P Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM RS/6000 7043 43P Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM RS/6000 7043 43P Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM RS/6000 7043 43P Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM RS/6000 7043 43P Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM RS/6000 7043 43P Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
