IBMメーカーT T 541の使用説明書/サービス説明書
ページ先へ移動 of 26
ENGLISH T541 Flat Panel Monitor User Guide.
i i First Edition ( September / 2002) This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time.
ENGLISH 1 Setting up the monitor ...............................................................................................2 System Hardware Requirements .........................................................................2 Handling Instructions .
2 Setting up the monitor Handling Instructions Handling Instructions 1. Do not support the monitor within the screen area. The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure. 2. Before using your monitor for the first time, remove the clear protective film from the front of the screen.
ENGLISH 3 Desk T op Use - Remove the clip on stand models Before adjusting your monitor for the first time, remove the locking clip on rear of the stand.
4 Connecting your Monitor Monitor Installation 1. Turn off your computer and all attached devices. Next, unplug the power cord(s) to your computer and all attached devices. 2. Connect the signal cable. The analog signal cable is already connected to your monitor.
ENGLISH 5 1. Switch on your monitor by pushing and releasing the power switch marked [ ] at the front of the bezel. [To switch off your monitor, push and release the power switch again.] 2. Switch on your computer. 3. If you are using the analog connector, run AUTO SETUP by following the instructions in the Auto Setup section on page 9.
6 To use the Plug and Play feature in Microsoft ® Windows ® 95 or Windows 98, files should be loaded from the IBM Monitor CD . 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit.
ENGLISH 7 To use the Plug and Play feature in Microsoft Windows 2000 or Microsoft Windows Millennium Edition(Me) files should be loaded from the IBM Monitor CD . 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly.
8 To use the Plug and Play feature in Microsoft Windows XP files should be loaded from the IBM Monitor CD . 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit.
ENGLISH 9 For digital input, image setup is not required. When you first use your monitor, you must perform Auto Setup for analog input. If you are using digital input, continue with the instructions on page 13. This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing.
10 1. Turn on the monitor first; then the co m puter. If the message CHECK VIDEO CABLE is displayed, or if nothing is displayed, check: • that the video interface cable is not connected properly. • the correct video adapter card is not installed. 2.
ENGLISH 11 1. Turn on the monitor first; then the computer. If the message CHECK VIDEO CABLE is displayed, or if nothing is displayed, check: • that the video interface cable is not connected properly. • the correct video adapter card is not installed.
12 Normally, you can complete the setup procedure using Image S etup , however, if your screen image is still distorted after you perform Image S etup or the setup CD does not run on your system, perform M ANUAL S ETUP . 1. Have your monitor turned on for about 15 minutes, until the monitor warms up.
ENGLISH 13 i This section gives advice on how you can work comfortably and reduce fatigue. Rest Take regular breaks. Vary your posture, stand up and stretch occasionally as prolonged use of computer workstations can be tiring. Back Sit back in your chair and use the backrest.
14 Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows: • Gently wipe the covers and the screen with a soft cloth.
ENGLISH 15 Adjusting Y our LCD Monitor User controls USER CONTROL FEATURES Icon Direct Access Functions i The image is already optimized for many display modes, however the user controls can be used to adjust the image to your liking. i The settings are saved after adjustment and when exiting the OSD and will be effective thereafter.
16 The settings adjustable with the user controls are viewed through the On - Screen Display (OSD). Press the enter button [ ] to display the main OSD menu. Initial appearance of OSD main menu; On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day.
ENGLISH 17 OSD Icon Select the COLOR MODE you find most comfortable or fine tune the colors using the USER COLOR MODE menu, if necessary. Description Sub-menu(s) MANUAL • Fine • Coarse Preset 1 (P.
18 OSD Icon Sub-menu(S) • YES • NO Controls and Adjustments Description RESET OSD SIZE Language Changes the size of the OSD menu on the screen. The language chosen affects only the language of the OSD. Select one of the five language to use for the OSD.
ENGLISH 19 i If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT monitor temporarily until you have reconfigured the computer, preferably to 1024 x 768 at 60Hz.
20 To benefit from power management, the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association (VESA) Display Power Management Signaling (DPMS) Standard.
ENGLISH 21 T roubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem No power to monitor.
22 i For image problems, you may want to run A UTO S ETUP again before consulting to this section. In most cases, A UTO SETUP can fix the problems. See Auto Setup for the computer on page 9 for details. Problem Possible Cause Suggested Action Reference There are noises in the video signal The color setting may be incorrect.
ENGLISH 23 This color monitor (Type-model 9512-Hxx) uses a 15-inch TFT LCD. i Power consumption figures are for the monitor and the power supply combined. Weight 5.3 kg (11.68 lbs) 15-inch (381.0 mm) 304.1 mm 228.1 mm 0.297 mm (H) x 0.297 mm (V) 100 - 240 Vac 60/50 ± 3Hz 0.
24 Addressabillty Refresh Rate / Range ( + / - 3%) Horizontal Frequency / Range ( + / - 3%) 640 x 480 58.2 ~ 61.8 Hz 30.56 ~ 32.45 kHz 640 x 480 64.0 ~ 68.0 Hz 33.95 ~ 36.05 kHz 640 x 480 72.8 ~ 77.3 Hz 36.38 ~ 38.63 kHz 640 x 350 67.9 ~ 72.1 Hz 30.56 ~ 32.
デバイスIBM T T 541の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IBM T T 541をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIBM T T 541の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IBM T T 541の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IBM T T 541で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IBM T T 541を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIBM T T 541の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IBM T T 541に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIBM T T 541デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
