IcomメーカーIC-F60Vの使用説明書/サービス説明書
ページ先へ移動 of 48
INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
i SAFETY TRAINING INFORMA TION Y our Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and clas- sified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such haz- ards.
ii G INFORMA TION • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.
iii IMPOR T ANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver . SA VE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F50V VHF TRANSCEIVER and IC-F60V UHF TRANSCEIVER .
iv PRECAUTIONS R W ARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body , especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical.
T ABLE OF CONTENTS SAFETY TRAINING INFORMA TION …………………………………………… i IMPORT ANT ……………………………………………………………………… iii E.
1 1 ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Supplied accessories * There are no names on the programmable function keys since the functions can be freely assigned to [P0] to [P3], [Red], [ ] and [ ] keys. Attach the supplied key stickers above the appropriate keys for easy recognition of that key’s assigned function.
2 1 ACCESSORIES ■ Accessory attachments D Flexible antenna Connect the supplied fl exible antenna to the antenna connector . CAUTION! • NEVER HOLD the antenna when carrying the transceiver . • T ransmitting without an antenna may damage the transceiver .
3 1 ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ï Jack cover Attach the jack cover when the optional equipment is not used. D Belt clip Attach the belt clip to the back of the transceiver with the supplied screws.
4 2 P ANEL DESCRIPTION ■ Front, top and side panels q VOLUME CONTROL [VOL] T urns power ON and adjusts the audio level. w RED BUTTON The desired function can be assigned by your dealer . (p. 8) e ANTENNA CONNECTOR Connects the supplied antenna. (p. 2) Microphone Function display (p.
5 2 P ANEL DESCRIPTION 2 r EXTERNAL SPEAKER-MICROPHONE JACK [SP MIC] Connects the optional speaker-microphone, etc. t DEALER-PROGRAMMABLE KEYS [P0] to [P3] The desired functions can be assigned independently by your dealer . (p. 8) y CH UP AND DOWN KEYS [ ]/[ ] Push to select an operating channel, etc.
6 2 P ANEL DESCRIPTION ■ Function display q RECORD INDICA TOR ➥ Appears when an unread message is in the memory . ➥ Blinks while recording. w LOW POWER INDICA TOR Appears when low output power is selected. e AUDIBLE INDICA TOR ➥ Appears when the channel is in the ‘ audible ’ (unmute) condition.
7 2 P ANEL DESCRIPTION 2 i BA TTERY INDICA T OR Appears or blinks when the battery power decreases to a speci- fi ed level. o ALPHANUMERIC DISPLA Y Displays an operating channel number , channel names, Set mode contents, DTMF code, etc. * 1 BIIS operation only * 2 MDC operation only ! IC-F50V_F60V_0.
8 2 P ANEL DESCRIPTION ■ Programmable function keys The following functions can be assigned to [P0] , [P1] , [P2] , [P3] , [Red] , [] and [] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming.
9 2 P ANEL DESCRIPTION 2 SCAN B ST ART/STOP KEY ➥ Push to start and cancel scanning operation. Scan resumes afte r a speci fi ed time period has passed when scan is cancelled except for this key . ➥ Push and hold this key for 1 sec. to indicate the scan group, then select the desired scan group using [CH Up]/[CH Down].
10 2 P ANEL DESCRIPTION MONITOR KEY ➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing and hold- ing this key .
11 2 P ANEL DESCRIPTION 2 T ALK AROUND KEY Push to turn the talk around function ON and OFF . • The talk around function equalizes the transmit frequency to the re- ceive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to toggle the IF bandwidth between wide and narrow .
12 2 P ANEL DESCRIPTION EMERGENCY KEYS Push and hold to transmit the emergency call. • The emergency call transmits with beeps; the display does not change. • The transceiver can transmit the emergency call silently or with the display changes depending on the pre-setting.
13 2 P ANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 COMP ANDER KEY Push to turn the compander function ON and OFF . The compander function reduces noise components from the trans- mitting audio to provide clearer communication. USER SET MODE KEY ➥ Push and hold to enter user set mode.
14 3 BASIC OPERA TION ■ T urning power ON q Rotate [VOL] to turn power ON. • When the opening vibration function is turned ON, the transceiver vibrates for 2 sec. Ask your dealer for details. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer .
15 3 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), this call procedure may be necessary prior to voice trans- mission.
16 3 BASIC OPERA TION ■ Receiving and transmitting NOTE: T ransmitting without an antenna may damage the trans- ceiver . See p. 2 for antenna attachment. Receiving: q Rotate [VOL] to turn power ON. w Push [CH Up] or [CH Down] to select a channel. e When receiving a call, adjust the audio output level to a comfort- able listening level.
17 3 BASIC OPERA TION 3 D Receiving note • Vibration function (Depends on the version) When the matched RX code signal is received, the transceiver may vibrate for a specified time period, depending on the pre-setting. Push any key or [PTT] to stop the vibration.
18 3 BASIC OPERA TION D TX code channel selection If the transceiver has [TX Code CH Select] assigned to it, the indi- cation can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up] or [CH Down] se- lects the TX code channel.
19 3 BASIC OPERA TION 3 e Push [TX Code CH Select] to select the desired digit to be edited. r Push [CH Up]/[CH Down] to select the desired digit. t Push [TX Code CH Select] to set. The digit to the right will blink automatically . y Repeat r and t to edit all allowable digits.
20 3 BASIC OPERA TION ■ User set mode User set mode is accessed at power ON and allows you to set sel- dom-changed settings. Y ou can “ customize ” the transceiver opera- tion to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [ ] and [ ], rotate [VOL] to power ON.
21 3 BASIC OPERA TION 3 ■ Emergency transmission When [Emergency] is pushed for the specified time period, an emergency signal is automatically transmitted. When [Emergency] is pushed for the specified time period, the DTMF emergency signal is transmitted once or repeatedly on the emergency channel.
22 3 BASIC OPERA TION ■ Recording function (Depends on the version) The transceiver has a recording function that records the TX/RX voice messages. When the speci fi ed ID is received, the automatic recording function activates and records the voice message for a speci fi ed time period.
23 3 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 e Release [PTT] to receive. • The RX voice message is recorded. r Push [Playback/Rec] again to stop recording.
24 4 BA TTER Y CHARGING ■ Caution R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger . Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger . Using third-party or counterfeit battery packs or charger may cause smoke, fi re, or cause the battery to burst.
25 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 R DANGER! NEVER solder the battery terminals or NEVER mod- ify the battery pack. This may cause heat generation, and the bat- tery may rupture, emit smoke or catch fi re. R DANGER! Use the battery only with the transceiver for which it is speci fi ed.
26 4 BA TTERY CHARGING D D Charging caution R DANGER! NEVER charge the battery pack in areas with ex- tremely high temperatures, such as near fi res or stoves, inside a sun heated car , or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat- tery to stop charging.
27 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Optional battery chargers ï Regular charging with the BC-152 q Attach the BC-152 to a fl at surface, such as a desk, if desired. w Connect the AC adapter (BC-147) as shown below.
28 4 BA TTERY CHARGING D For your convenience Eyelet USE a rubber band to secure the transceiv- er while charging, if desired. ! IC-F50V_F60V_0.qxd 07.
29 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ï AD-100 installation The AD-100 CHARGER ADAPTER must be installed into the BC-1 19N or BC-121N before battery charging.
30 4 BA TTERY CHARGING D Rapid charging with the BC-1 19N+AD-100 The optional BC-1 19N provides rapid charging of the optional Li- Ion battery pack. The following items are additionally required: • An AD-100 charger adapter • An AC adapter (may be supplied with BC-1 19N depending on ver- sion) or the DC power cable (OPC-515L/CP-17L).
31 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 D Rapid charging with the BC-121N+AD-100 The optional BC-121N allows up to 6 battery packs to be charged simultaneously .
32 5 BA TTER Y CASE ■ Optional battery case (BP-226) When using the optional battery case attached to the transceiver , install 5 × AA (LR6) size alkaline batteries as illustrated at right. The BP-226 is constructed to the IPX4 waterproof standard (IEC 60529, 2006).
33 5 BA TTERY CASE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 q w e BP-226 Latch Fig.1 Fig.2 Ribbon Fig.3 Gasket Ribbon ! IC-F50V_F60V_0.qxd 07.
34 6 SPEAKER-MICROPHONE ■ Optional HM-168 description NEVER immerse the connector in water . If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver . NOTE: The microphone is located at the top of the speaker-mi- crophone, as shown in the diagram above.
35 6 SPEAKER-MICROPHONE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Attachment Attach the connector of the speaker-microphone into the [SP MIC] jack on the transceiver and tighten the screw . IMPORT ANT : KEEP the [SP MIC] jack cover attached to the transceiver when the speaker-microphone is not in use.
36 7 SWIVEL BEL T CLIP ■ Optional MB-86 contents Qty . q Belt clip ………………………………………………………………… 1 w Base clip ………………………………….
37 7 SWIVEL BEL T CLIP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 e Once the transceiver is locked in place, it will swivel 360 de- grees. ■ Detaching T urn the transceiver upside down, and pull out from the belt clip. Then detach the base clip from the back of the transceiver .
38 8 OPTIONS D D BA TTER Y P ACK/CASE • BP-226 BA TTERY CASE Battery case for 5 × AA (LR6) alkaline cells. • BP-227 L i - I on BA TTERY P ACK 7.2 V/1700 mAh Li-Ion battery pack. The same as supplied with the transceiver . BP-227 must be charged with the optional BC- 152/BC-1 19N/BC-121N.
39 8 OPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 D D DC CABLES • CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-152/BC-1 19N) • OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13.
40 8 OPTIONS ï About VS-1SC VOX / PTT CASE The VS-1SC is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.
41 8 OPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VOX gain and delay adjustment q Attach the connector of the VS-1SC into the [SP/MIC] connector on the transceiver and tighten the screw . • T oggle the toggle switch to [VOX]. w Enter user set mode.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6604H-1EX Printed in Japan © 2007 Icom Inc. Printed on recycled paper with soy ink. ! IC-F50V_F60V_0.
デバイスIcom IC-F60Vの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Icom IC-F60Vをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIcom IC-F60Vの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Icom IC-F60Vの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Icom IC-F60Vで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Icom IC-F60Vを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIcom IC-F60Vの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Icom IC-F60Vに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIcom IC-F60Vデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
