IDEAL INDUSTRIESメーカーIZGS 68 ICTXの使用説明書/サービス説明書
ページ先へ移動 of 20
Gas Hob IZGS 68 I CTX EG.
2 Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual car efully and keep it throughout the pr oduct life cycle as a refer ence document.
3 Important Safety Information ............................................................................. 4 Description of the appliance .............................................................................. 6 Operation ....................
4 Installation The work of installation must be carried out by competent and qualified installers according to the regulations in force. • Any modifications to the domestic electrical mains which may be necessary for the installation of the appliance should be carried out only by competent personnel.
5 appliance. A poor air supply could cause lack of oxygen. • Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device.
6 Description of the appliance 1 Auxiliary burner 2 Semi-rapid burner 3 Triple crown burner 4 Control knobs 3 2 1 2 4.
7 Operation Hob burner control knobs The symbols on the knobs mean: = no gas supply = maximum gas supply = minimum gas supply For easier lighting, proceed before putting a pan on the pan support . Lighting the burners To light a burner, turn the relevant knob anticlockwise to maximum position ( ) and push down the knob to ignite.
8 Using the hob corr ectly Practical hints The burners To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used.
9 Cleaning and Mainteinance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine.
10 The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers.
11 Cut out dimensions (see chapter “Building In”) W idth: 560 mm Depth: 480 mm Overall dimensions W idth: 594 mm Depth: 510 mm T echnical data Heat Input T riple Crown burner 4,0 kW Semi-rapid bur.
12 Installation The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in for ce.
13 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). Important When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation.
14 A. Injectors replacement • Ensur e that the gas taps are in the 'OFF' position • Isolate the hob from the electrical supply • Remove all pan supports, burner caps, rings, cr owns and control knobs.
15 The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
16 Remplacement of the voltage cable The connection of the voltage cable to the appliance's terminal block is of type "Y". This means that its replacement requires the specific equipment of a technician. In this case, only cable type H05V2V2-F T90 must be used.
17 Building In These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 4; the cut out dimensions are shown in Fig. 5. The edge of the cut out must have a minimum distance from the rear wall of 55 mm.
18 Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig.
19 Fig. 9 Fig. 10 Service and original spar e parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention.
3971350.01 05/09 R.A.
デバイスIDEAL INDUSTRIES IZGS 68 ICTXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
IDEAL INDUSTRIES IZGS 68 ICTXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIDEAL INDUSTRIES IZGS 68 ICTXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IDEAL INDUSTRIES IZGS 68 ICTXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IDEAL INDUSTRIES IZGS 68 ICTXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IDEAL INDUSTRIES IZGS 68 ICTXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIDEAL INDUSTRIES IZGS 68 ICTXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IDEAL INDUSTRIES IZGS 68 ICTXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIDEAL INDUSTRIES IZGS 68 ICTXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
