iLiveメーカーT SERIES AP6526の使用説明書/サービス説明書
ページ先へ移動 of 111
System Reference Guide January 2008 Publication AP6526 iLive and T Series System Reference Guide March 2009 Firmware Version 1.4 Publication AP6526 issue 3.
2 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 ALLEN & HEATH The iLive range of products complies with the European Electromagnetic Compatibility directives 89/336 /EEC & 92/31/EEC and the European Low Voltage Directives 73/23/EEC & 93/68/EEC.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 3 Important Safety Instructions WARNINGS - Read the following before proceeding : ATTENTION: RISQUE DE CHOC ELECTRIQUE – NE PAS OUVRIR Read instructions : Retain these safety and operating instructions for futur e reference.
4 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Important Mains plug wiring instructions. The equipment is supplied with a moulded mains pl ug fitted to the AC mains power lead. Follow the instructions below if t he mains plug has to be replaced.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 5 This is the iLive System Reference Guide relating to Version 1.4 Firmware. The system firmware is updated on a regular basis as new features and impr ovements are added. Some of the screen shot s and details in this guide may differ from thos e in the current release of firmwar e.
6 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Assigning SoftKeys ................................................................................... 70 Assigning PL devices .....................................................................
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 7 W elcome Thank you fo r investing in the Allen & Heath iLive digital mixing system. To get the most from your iLive please read the Getting Started Guide that comes with your system and refer to this reference guide for further information.
8 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 iLive System components iDR10 MixRack The MixRack is the heart of the digital audio processing system. It houses the DSP mix engine together with control and audio networking interfaces. The 64 input x 32 bu s architecture is fully configurable for mono/stereo and type of mix.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 9 MIC/LINE IN module 8x mic preamps with remote gain control. DUAL MIC/LINE IN module Connect 16x in puts on screw terminal plugs. 8x mic preamps each with remote selection of A and B inputs. DIGITAL IN module 4x pairs of digital inputs selectable either AES, SPDIF or OPTO.
10 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Control strip Meter Status LCD Encoder SEL key PAFL Mute MIX key Fader Configure as: Input channel FX return FX send Group Aux Main mix Matrix D.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 11 T Series System components PL-6 Encoders PL-5 The T Series MixRack is the heart of the digital audio processing system, housing the DSP mix engine together with control and audio networking i nterfaces.
12 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 T Series Control layout Channel Processing Strip Analogue style control section with dedicated rotary controls, switche s and meters for the channel or mix preamp, HPF, gate, PEQ, compressor and limiter/de-esser.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 13 Connecting the iLive MixRack and Surface The iLive has two main sy stem connections b etween the Surface an d MixRack, both usin g CAT5 cables.
14 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 An IEC mains power cord with moulded plug suitable for your territory is provided for each power supply module within the system. The iLive system uses universal voltage power supplies that accept world wide main s sources from 100 to 24 0V.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 15 Connecting the T Series MixRack and Surface Adding PL Series controllers Use CAT5 cable to connect the MixRack PL-Anet port to the PL device IN socket. Daisy chain OUT to the next unit, or use a PL-9 hub for star connection.
16 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Booting up the system Turning on the system Note : Always turn the MixRack on first, then t he iLive Surface. The iLive system remembers its last sett ings on power up. 1. First, plug in the mains and C AT5 cables.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 17 The Status screen The TouchScreen ‘Status’ page is displayed when the fader strip SEL key s and the keys below the screen a r e a l l of f . It i s t he d e f au l t v ie w wh en n ot hi n g i s s e le c t e d.
18 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Clock Displays the TouchScreen CPU real ti me clock. The time may be changed from the UTILITY / Configur atio n / Dat e Tim e page. Current User The current User name is displayed h ere. To log in as a different user go to the UTILITY / Change User p a g e .
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 19 Surface basics – The T ouchScreen The TouchSc reen provides a graphical disp lay of the parameters and assignment s, allows configuration of the system, and management of the memories and da ta.
20 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 All screen keys tu rned off – STATUS With all the screen keys and strip SEL keys turned off the TouchScreen displays the Status page. This sho ws system status includin g firmware, temperature, audio system lock and digital audio network status.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 21 FX Access the FX rack. Provides 8 virtual ‘ rack positions’ for loading your choice of processing from a library of effects devices including reverbs, delays, modulators and more. A Front Panel vie w presents a familiar control interface for parameter data e ntry.
22 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Surface basics - F ader control strip The Fader Control Strip is the primary user interface for mixing with iLive. It provides a familiar analogue console layout and is arran ged in banks acr oss the surface.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 23 Rotary encoder This control lights up when it has a function as signed. It is used as a send level, PAN or image control depending on the type of mix currently selected with the MIX key and whether it is a fader or rotary mix.
24 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Fader The fader is motorised and automatically changes position wh en you select different fader layers or change the mix using the MIX keys. They also change to show the mix master GEQ (graphic EQ) settings when in GEQ FADER FLIP mode.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 25 Surface basics – The SEL key The primary function of the fader control strip SEL keys is to access the signal processing and rout ing for the channels, FX, mix or DCA masters. These keys are also used while in system setup mode to configure the strip functions, names and colours.
26 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using a SEL key to access Input Channel P arameters PARAMETER CONTROLS - Press an IP (Input) channel SEL key to access the parameters for that channel using the analogue style controls in the processing block to the left of the screen.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 27 Using a SEL key to access Mix Master P arameters PARAMETER CONTROLS - Press a GP, AUX, FX, MAIN or MTX (Mix) master SEL key to access the parameters for t hat master using the analogue style controls in the processing block to the left of the screen.
28 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using a SEL key to access Short FX Return P arameters The iLive ‘RackExtra’ DSP module provides a virtual rack to load up to 8 effects devices such as reverbs, delay s and modulators. An FX ‘short return’ is a stereo input channel that returns the output of th e device to the mix.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 29 Using a SEL key to access DCA Settings With all TouchScreen keys off press a DCA master strip SEL key to open its assignment view. Touch the screen buttons to toggle the assignments on or off. The screen provide s an alternative to using the MIX keys to view and change DCA assignments.
30 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Surface basics – The MIX key The primary function of the fader control strip MIX keys is to a cces s the rout ing a nd le vels for th e dif fere nt mixes, and to assign the DCAs.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 31 Using the Master MIX key - View all sends feeding one mix. 1. Press MIX on the mix master strip.
32 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using the Channel MIX key - View all sends from one channel. 1. Press MIX on an input ch annel strip. View the current send s and assignments from that channel on the m aster strip LCDs and faders/rotaries.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 33 Channel and Mix processing iLive provides plenty of signal processing fo r its input channels, effects returns, mix masters and up to 8 internal FX devices. This replaces the large racks of out board equipment that typically accompany the traditional analogue mixing system.
34 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 PREAMP (DUAL MIC/LINE IN) I f t h e d u a l i n p u t module is detected then the screen includes a touch button to select between the A an B inp ut connections.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 35 GATE (Channel only) The noise gate provides a f ull set of controls and signal metering as you woul d find on a top grade outboard processor. A self keyed side chain filter may be switched in or out.
36 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 PEQ (Channel, FX return and Mix) The equaliser is 4-band fully parametric with cut/boost, swept frequency and width co ntrols per band. The HF and LF bands may be switched as shelving, bell or pass type filters.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 37 COMPRESSOR (Cha nnel and Mix) The compressor provides a full set of traditional controls and signal metering as you would find on a top grade outboard processor. A self keyed side chain filter may be switched in or out.
38 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 LIMITER / DE-ESSER (Limiter on Channe l and Mix, De-Esser on Channel only) This is the last of three dynamics processors available on every input channel.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 39 Introducing the FX The iDR-64 ‘RackExtra’ DSP module provides a virtual ‘ FX rack’ which can be configured with up t o 8 processors including reverbs, delays, modulators an d more.
40 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Back Panel view - Con figure the FX routing Touch the top right Back Panel button to open up the connections v iew. This emulates patching up a typical outboard effects rack. Configure the FX device as a send/return loop or insert ed into a channel or mix signal path .
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 41 Front Panel view – Work with the FX parameters Access FX parameters fr om the strips Pre ss an FX send m aster strip SEL key, or press an FX short return (IP FX ) strip SEL key to open up the FX screen.
42 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Choose the FX – The FX pres et library Touch the Library button to open up the library list. The presets are grouped into Factory, User and USB. Factory Default presets that cannot be overwritten, and can be use d as the starting point for creating your ow n presets.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 43 Reverbs - SMR Spatial Modelling Reverberator . These provide high quality stereo reverb effects based around 4 complex spatial mo dels - Classic, Hall, Room and EMT. Each of these models employs different reflection and decay algorit hms to provide natural sound spaces .
44 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Modulation FX - ADT The ADT DOUBLER is an automatic double tracking module for creating short echo/chorusing effects, classic double tracking and ‘slapback’ tape delay loops.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 45 Gated Verb ‘Gated Verb’ hosts the classic 80’s emulation plus ‘ panned’ and ‘powerbox’ gated reverb presets. The user interfa ce gives instant access to lo-cut hi-cut decay spectrum filters and the gate envelope controls.
46 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 P atching the Outputs Press the OUTPUTS key below the TouchScreen to access the output routing patch bays. These virtual patch panels display the p hysical and digital audio network output sockets recognise d by the system and let you route any signal to any output.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 47 Output Sources The user assigned n ame is displayed below the channel number. If a channel is not a vailable a red cross appears. Note: If sockets have been assign ed as INSERT Sends then t hey are not available to be assign ed using the OUTP UTS page .
48 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using DCA groups iLive provides 16 DCA group s. These behave in a simila r way to conventional analo gue console VCA groups. You may assig n as many of these as you ch oose to the Surface strips.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 49 Channel Ganging Ganging lets you link selected processing and mix p a r a m e t e r s b e t w e e n i n p u t c h a n n e l s o r m a s t e r s , f o r example the EQ, gate and compressor of a stereo keyboard, or the GEQ of the L and R main mix.
50 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using the COPY / P ASTE /RESET edit keys iLive provides a quick and intuitive edit func tion to copy or reset settin gs between channels, processing blocks and mixes. This uses dedicated ed it keys on the Surface rather than complex screen menus.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 51 COPY H o l d d o w n C O P Y t h e n p r e s s t h e SEL or MIX key a s s o c i a t e d w i t h t h e p a r a m e t e r s y o u w a n t t o c o p y . T h i s p u t s t h e parameters on to a ‘clipboard’ to be pasted later.
52 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 The METERS screen Press the METERS key below the TouchScreen to view pages of audio meters. You can configure and view up to 4 ‘User’ meter pages. The RTA frequency analysis display is ava ilable within this view.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 53 P AFL monitor system iLive features a comprehensive engineer’s monitoring system with headphones and local monitor outputs available at the Surface, and headphones duplicated at the MixRack.
54 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 PFL/AFL mode keys Master keys to the right of the strips select the function of the PAFL keys to be PFL (pre-fade listen) or AFL (after-fade listen). Signals are monitored in m ono or stereo depending o n their configuration.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 55 PAFL IN sockets This pair of balanced, line level XLR inputs on the rear of the iLive Surface lets you add an ex ternal signal to the PAFL mix.
56 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 TouchScreen PAFL functions Press the TouchScreen PAFL key to open a page of option settings f or the PAFL monitoring system. Set these according to your preferred way of working. These settings are retained on power down.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 57 Engineer’s W edge / IEM monitoring The iLive and T Series are capable of being configured for dedicated monitor mixing. It can provid e an engineer's dual Wedge/IEM facility for monitor mixing with combinatio ns of stage wedge speakers an d in- ear monitors.
58 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 T alkback system iLive provides a fully featured engineer’s Talkback syst em. This uses dedicated Talk keys and is quick to assign to the outputs w ithout the need to access sc reen menus.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 59 Talkback setup and preferences TALK key action Select either momentary o r latching operation. Go to the SURFACE SETUP / Preferences page.
60 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 SoftK eys 8 SoftKeys to the right of the TouchScreen can be assigned t o different functions to suit your a pplication.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 61 MIXRACK setup The MixRack is the heart of the system and f eatures a 64 channel x 32 mix bus audio architecture that is fully configurable by the user. Once configured yo u can map the channels and masters to the Surface strips and layers in any combination.
62 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Top screen W e r e f e r t o t h i s a s t h e ‘ r a d a r v i e w ’ a s i t p r o v i d e s a n o v e r v i e w o f t h e c u r r e n t system configuration. Use the menu buttons to access a nd change the configuration and other MixRack setup functions.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 63 Mixer Config page T h i s s c r e e n l e t s y o u c h a n g e t h e m o n o / s t e r e o configuration of the input channels, and the architecture of the mix buses. Note: Changing these settings reconfigures t he DSP architecture and resets parameters.
64 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 The Main Mix iLive features a choice of many different conf igurations of main mix from mono to 4way and with different types of image control. Note that due to the DSP architecture the buses are always allo cated in pair s.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 65 Mixer Pref / Direct Output page This page lets you set the source to the input channel direct outputs. The se tting is global and affects all direct outputs. You can choose the point w ithin the channel signal path and whether or not it follows the main channel mute and /or fader.
66 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Remote B Config Here you co nfigure the way the MixRack Port B EtherSound ESB network (if fitted) is set up to work. This configures the MixRack EtherSound interface cards so that the slave audio is downstream of the master.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 67 Signal Generator page Provides a comprehe nsive tone / noise generator which can be use d for checking and setting up the system. The generator settings are restored on power up and stored in the system Show memories.
68 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 SURF ACE setup Once the MixRack audio architecture has been configured using the MIXRACK SETUP screen, you can assign the channels, mix masters, DCA group master s and Wedge/IEM masters to the Surface strip s.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 69 Assigning the Surface Strips To assign a Single Strip Touch the Single Assignment butt on. Press the SEL key on the strip you want to assign. Use the drop down menu to select the Channel Type you wish to assign.
70 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Assigning the Soft Keys 8 SoftKeys to the right of the TouchScreen can be assigned to different functions to suit your application.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 71 Assigning PL Devices Allen & Heath PL remote control device may be plug ged into either the MixRack or the Surface. These provid e controls such as faders, rotary encoders, switches, indicators and logic GPIO which may be assigned by the user to suit the application.
72 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 The Surface ALT VIEW key The Surface fader strip LCDs normally di splay the channel names. Hold down the ALT VIEW key to display alternative information such as channel or socket number, or dB value.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 73 Setting the Surface P references You can set user preferences for how the iLive Surface functions. Go to the SURFACE SETUP / Preferences page. Link Fader Banks Set the Surface fader banks for in dependent or linked layer operation across all banks.
74 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Name and Colour Each Input channel, mix master and DCA master can ha ve a 5 character name and one of 6 colours or no backlight applied. The names appear on th e strip LCDs and TouchScreen pages, and the colour affects the strip LCD backlights.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 75 User Profiles iLive lets you set up and work with up to 8 'User Profiles'. You can set p ermissions and a password for each to restrict operator access to certain functions.
76 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Library memories You can name, store and recall parameter settings as Us er libraries, or recall factory presets from the Library pane in each processing screen. Touch the Library button to open up the library view.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 77 Scene memories iLive has 250 Scene memories. These are 'snapshots' of all or a selection of the live mixing parameters. They do not store the DSP bus config uratio n and user preferences.
78 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using the Edit SCENE CONTENTS page Add selected parameters to a Scene You can store ‘partial’ Scenes. Select items from the list in the left hand window to add to the scene. Expand and collapse the tree list using the + and – butt ons.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 79 Scene parame ters The diagram below list s the items that may be selected and added to the Scene memories. It also illustrates where the different parameters ex ist in the signal chain. The items are arranged as a tree view.
80 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Show memories You can archive your configuration as a S how memory. Show memories overwr ite all the setti ngs . These include all current parameters, system DSP and control configuration, all 250 Scenes and the user preferences.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 81 To archive your configuration go to the UTILITY / Configuration / Show Manager screen. Touch the Archive Show button. Type in a name using the onscreen keypad. Press En ter to archive the show. This takes a few seconds to complete.
82 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Using TEMPLA TE Shows The iLive has a fully configurable audio architecture, control layout and socket p atching letting you customise the way you work. It would be a daunting task for the new user if we gave them a ‘blank c a n v a s ’ t o s t a r t f r o m s c r a t c h .
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 83 USB Scene T ransfer Recalling a Show completely overwrites all system se ttings and the system configuration. This may not b e ideal in a festival situation where several guest eng ineer s arrive with their settings stored as Shows on their USB keys.
84 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 W orking with USB data iLive can transfer its Show memories, libraries an d log files between the onboard c omputer and an external PC or another iLive s ystem via a USB memory k ey. You can also recall a show directly from the key without the need to copy it to the Surface first.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 85 The UTILITY screen The UTILITY screen provides access to many setup, di ag nostic and user preferen ce functions.
86 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Configuration page Provides access to the memory management, time setup and M IDI settings. Date / Time View the current day and clock settings for the MixRack, Surface and TouchScreen.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 87 Firmware page Lets you check the current system firmware versions and load in new firmware using a USB key. Firmware Versions D i s p l a y s t h e c u r r e n t firmware versions for the TouchScreen, Surface and MixRack.
88 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Network page Lets you view and change the system unit names and network settings. Network Connections T h i s p a g e d i s p l a y s t h e n a m e s , n e t w o r k addresses and connection st atus of the devices currently connected via Ethernet to the onboard TouchScreen computer.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 89 iLive Module options – Analogue inputs and outputs MIC/LINE Input part M-MICIN-A This is the main audio input module for the iLive system. I t provides 8x high performance analogue input preamps f or microphone and line level signals.
90 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Module options – Digital inputs and outputs DIGITAL INPUT part M-DIGIN-A This module provides 8 digital inputs arranged as four pair s. Each offers a choice of digital format - AES, SPDIF or optical (TOSLINK).
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 91 Module options – Digital outputs DIGITAL MULTI OUT part M-MULTI-OUT-A This module provides 16 o utputs and therefore uses two slots at the MixRack or Surface. Use the iLive OUTPUTS patch bay to map any signal to any output socket.
92 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Module options - System iDR-64 RackExtra DSP This is the DSP mix engine, the ‘brain s’ of the iLive system. The DSP (Digital Signal Processing) handles the audio signal processing such as EQ, dynamics, delays and mixing.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 93 Module options - System CPU module Provides the control interface to the MixRack. This module is identified as the ‘iDR RACK CPU’. It is not interchangeable with the iLive Surface CPU module.
94 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 MIDI Specification Scene number Input Channel number FX Send SS SS CC CC CC CC CC Hex Hex CH Hex CH Hex CH Hex CH Hex CH Hex 1 00 129 65 40 193 .
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 95 T echnical specification Format: Distributed dual network audio and TCP/IP c ontrol Separate DSP and control surface iLive = 4x surface sizes T .
96 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 iLive Digital inputs (8x channel = 4x stereo pairs): Select one of three formats per pair: AES3, SPDIF, Optical.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 97 Audio monitoring: 2x PAFL headphone amps (M ixRack and Surface) 2x sockets on surface - standard 1/4" and 3.
98 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 W eights and dimensions iLive Dimensions (Width x Height x Depth): MixRack iDR10 482mm (19”) x 400mm (15.75”) 9 U x 350mm (13.8”) MixRack iDR10 flightcase 643mm (25.3”) x 7 30mm (28.75”) x 669mm (26.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 99 iLive-80 753m m / 29.6" iL ive-112 1006 m m / 39.6" iLi ve-144 1206 mm / 47.5" iLive-176 1406 mm / 5 5.35" iLive-80 687m m / 27" All othe r models 940 mm / 37" iLive-176 23 3 mm / 9.
100 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 113 mm / 4.45" 582 mm / 22.9" 707 mm / 27.7" HEADPHONES, US B 44 mm / 1.73" 355 mm / 14" 91 mm / 3.6" 1017 mm / 40" 452 mm / 17.8" 152 mm / 6" 482 mm / 19" 350 mm / 13.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 101 iLive System block diagram 48V GAIN - + MIC/LINE PP PAD -25 ADC CHK SOURCE AES/ EBU SPDIF OPTICAL ANALOGUE IN DIGITAL IN CONTROL CONTROL INPUT .
102 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 T Series System block diagram 48V GAIN - + MIC/LINE PAD -25 ADC CONTROL INPUT PATCHB AY POLARITY HPF GATE PEQ COMP LIMITER DE-ESSER DELAY 0 POS.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 103 EtherSound system diagram ESA IN OUT IN OUT ESA IN OUT ESB iLIVE SURFACE MIXRACK UPSTREAM DOWNSTREAM CH1-32 CH33-62 CH63-64 SURFACE SLOT A-D OU.
104 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 Application diagrams These diagrams show how the iLive may be connected and configured to sat isfy a variety of applicatio ns. Note the connection of the CAT5 cables, the setting of the aud io clock source and ESB master / slave configuration.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 105 2 iLive I1-8 = ST A UX5-8 J1-4 = MTX1-4 J5-6 = ST MT X1 J7-8 = PAFL O UT MONITOR OUTPUTS 26x AU X = 8 m 2st 2FX 8x MTX = 4m 2st CONFIG C1-2 = A.
106 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 ALLEN&HEATH iDR-64 MIX E NGIN E ABC D EF G H I J iDR10 ESA OU T NETWORK 3 iLive ALLEN&HEATH iDR-64 MIX E NGIN E A-F = BLANK MONITOR INP.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 107 A B D C ABC D E F GHI J A1-E8 = I/P 1-40 FOH INPUTS FOH_8fx_LR Load Sh ow 8x GRP = 4 m 2st 18x A UX = 8m 1st 8FX MAIN = LR 8x MTX = 4m 2st CONFIG APPLICATION EXA MPLE - FOH / MONITOR (D igital mic splitter.
108 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 5 iLive AUDIO COPPER MULTICORE A B D C A1-8 = CH1-8 B1-8 = CH9-16 D1-8 = CH17-24 C1-4 = AUX1-4 C5-6 = LR Load S how 8x GRP = 4m 2st 16x AUX = 10m 1s t 4FX MAIN = LR 8x MTX = 4m 2st CONFI G APPLICATION EXAMPLE - iDR0 WI TH i LIVE AS A STAND ALONE MIXER 24 inpu ts, 8 o utputs compact system.
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 109 6 iLive FOH gain affects mo nitors but engi neer has digital channel trims ALLEN& HEATH iDR-64 MIX EN GINE ABC D E F GH I J D1-4 = MTX1-4 D.
110 ALLEN & HEATH iLive Reference Guide AP6526 iss.3 7 iLive Monitor gain a ffects FOH but engineer has channel digital trims Monitor engineer has control of preamp gain and phantom power A LLE N .
ALLEN & HEATH iLive Reference Guide AP6526 iss.3 111 8 iLive Monitor gain affects FOH but engi neer has channel digital trims APPLICATION EXAMPL E - FOH / MONITO R (iDR0 at FOH, No ESA on Monitor).
デバイスiLive T SERIES AP6526の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
iLive T SERIES AP6526をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはiLive T SERIES AP6526の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。iLive T SERIES AP6526の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。iLive T SERIES AP6526で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
iLive T SERIES AP6526を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はiLive T SERIES AP6526の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、iLive T SERIES AP6526に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちiLive T SERIES AP6526デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。