ImageメーカーIE53901の使用説明書/サービス説明書
ページ先へ移動 of 19
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee you complete satisfaction through direct assistance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUSTOMER HOT LINE.
2 IMAGE is a registered trademark of ICON Health & Fitness, Inc. Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Y ou Begin . . . .
3 1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions.
4 Weight Storage T ube Dumbbell Storage Rack Seat Pull-up Bar Upright Weight Guide Weight Glider Barbell Safety Spotter Curl Pad W arning Decal 1 W arning Decal 2 Leg Lever Right Side Left Side Note: .
5 Part Identification Chart—Model No. IMBE53901 R1200A Large W asher (70) M8 W asher (77) M10 W asher (6) M6 W asher (30) M10 Nylon Locknut (1 1) M8 Nylon Locknut (42) M8 x 20mm Bolt (75) M8 x 30mm .
6 1. Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled. Press a 50mm Square Outer Cap (20) onto each end of a Base (46). T urn the Base so the large hole is in the position shown.
7 3. Slide a Brace (44) onto the bracket on one of the Uprights (43). Attach the Brace to the Upright with two M10 x 65mm Bolts (68), four M10 W ashers (6), and two M10 Nylon Locknuts (1 1).
8 6. Have a second person hold the T op Crossbar (48) so that the pull-up bar faces away from the rack, as shown. Attach the T op Crossbar (48) to the left Upright (43) with two M10 x 70mm Bolts (21), a Small Support Plate (51), and two M10 Nylon Locknuts (1 1).
9. Identify the Left Safety Spotter (57) by the position of the handle and the Left Spotter Hook (45). Place the Left Safety Spotter on the left Base (46) so it is cen- tered over the indicated hole. Have a second person hold the Locking Bar (62) so that the Left Weight Glider (60) rests on top of the Left Safety Spotter (57).
10 13. Press a 50mm x 70mm Outer Cap (10) onto each end of the Stabilizer (13). Attach the Stabilizer (13) to the Bench Frame (5) with two M10 x 60mm Button Head Bolts (12) and two M10 Nylon Locknuts (1 1). Note: Position the Stabilizer so that the warning decal is in the position shown.
11 16. Press two 25mm x 40mm Inner Caps (28) into each Backrest T ube (27). Press two 25mm x 40mm Inner Caps into the Backrest Adjustment Bracket (35). Lubricate an M10 x 190mm Bolt (22). Attach the Backrest T ubes (27) to the welded tube on the Backrest Adjustment Bracket (35) with the Bolt, two M10 W ashers (6), and an M10 Nylon Locknut (1 1).
12 20. T urn the Seat (14) as shown. Attach the wide end of the Seat to the bracket on the Seat Mounting Bracket (23) with two M6 x 16mm Screws (3). T ilt the Seat Mounting Bracket (23) upwards and attach the narrow end of the Seat (14) to the Seat Mounting Bracket with an M6 x 35mm Bolt (34) and an M6 W asher (30).
13 25. Make sure all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page. 24. Attach the Curl Pad (8) to the Curl Upright (9) with two M6 x 16mm Screws (3).
A TT ACHING WEIGHTS TO THE BARBELL T o use the Barbell (63), slide the desired amount of weight (not included) onto each end of the Barbell. Secure the weights with the Large Weight Clips (67). Note: T o use standard weights, the Weight Adapters (61) should be removed from the Barbell.
15 ADJUSTING THE BACKREST T o raise the Backrest (15), grip the end of the Backrest with one hand and pull it upward until the Backrest Adjustment Bracket (35) locks into the appropriate tab on the bracket on the Bench Frame (5). T o lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards.
Part No. 172540 R1200A Printed in China © 2000 ICON Health & Fitness, Inc. T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays).
REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL SA VE THIS P ART LIST/EXPLODED DRA WING AND THE USER’S MANUAL FOR FUTURE REFERENCE 81.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts. Key No. Qty . Description Key No. Qty . Description Part List—Model No.
20 65 53 41 11 66 42 71 58 58 58 59 56 57 60 75 75 42 66 20 42 46 65 71 41 50 20 11 21 55 68 11 44 43 53 51 21 64 11 11 42 20 42 50 54 47 11 11 48 11 11 44 68 21 21 55 43 64 51 21 39 39 74 74 74 74 74.
デバイスImage IE53901の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Image IE53901をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImage IE53901の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Image IE53901の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Image IE53901で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Image IE53901を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImage IE53901の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Image IE53901に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImage IE53901デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。