ImageメーカーIMBE53991の使用説明書/サービス説明書
ページ先へ移動 of 18
® QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory .
2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are ade- quately informed of all precautions.
4 Weight Storage Tu b e Dumbbell Storage Rack Seat Pull-up Bar Upright Weight Guide Weight Glider Barbell Safety Spotter Curl Pad Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench; they do not refer to right and left on the drawings in this manual.
5 Part Identification Chart—Model No. IMBE53991 R1200A M10 Nylon Locknut (1 1)— 28 M8 Nylon Locknut (54)—1 1 M6 W asher (30)—5 M6 x 16mm Screw (3)—4 M8 x 60mm Bolt (39)—2 M6 x 38mm Bolt (6.
6 1. Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled. Press a 50mm Square Outer Cap (17) onto each end of a Base (7). T urn the Base so the large hole is in the position shown.
4. Slide the remaining Brace (2) onto the bracket on the other Upright (1). Attach the Brace to the Upright with two M10 x 65mm Bolts (42), four M10 W ashers (6), and two M10 Nylon Locknuts (1 1).
8 5. Press a 25mm Round Inner Cap (51) into the end of a Weight Storage Tube (21). While a second person holds the Middle Crossbar (8) in the position shown, insert two M10 x 70mm Bolts (46) through the bracket on the Weight Storage Tube (21), the left Brace (2), and the bracket on the Middle Crossbar .
8. Press a 25mm Bushing (48) into each end of the Locking Bar (34). Insert the Barbell (35) through the Locking Bar (34) until the Barbell is centered in the Locking Bar . 35 48 34 48 8 9. Identify the Left Weight Glider (32) by looking at the position of the round tube.
10 13. Note: If you are not planning to use Olympic weights with the weight bench, you do not need to perform this step. Keep the two Weight Adapters (33) in a safe place in case you need them in the future. Fully engage the indicated hook on both sides of the weight bench before beginning this step.
11 15. Press a 50mm Square Outer Cap (17) onto each end of the Small Stabilizer (25). Attach the Small Stabilizer (25) to the Front Leg (19) with two M10 x 65mm Carriage Bolts (40) and two M10 Nylon Locknuts (1 1). Note: There is an inden- tation around the holes on one side of the Small Stabilizer .
12 19. Lubricate an M10 x 1 15mm Bolt (55). Slide an M10 W asher (6) onto the Bolt. Attach the Backrest Adjustment Bracket (36) to the bracket on the Bench Frame (5) by guiding the M10 x 1 15mm Bolt (55) through the indicated side of the Backrest Adjustment Bracket (36), the bracket on the Bench Frame, and the 15mm x 10.
13 23. Place the Seat Support T ube (37) on the Bench Frame (5) so that the Seat Adjustment Bracket (45) fits over the welded pin (not visible in the drawing) on the side of the Bench Frame.
14 This section explains how the weight bench is adjusted. See the included exercise guide for important informa- tion about how to perform a variety of exercises and how to get the greatest benefit from your exercise program. Inspect and tighten all parts each time you use the weight bench.
15 ADJUSTING THE BACKREST T o raise the Backrest (15), grip the end of the Backrest with one hand and pull it upward. The Backrest Adjustment Frame (36) will automatically lock into one of the tabs on the bracket on the Bench Frame (5). T o lower the Backrest (15), grip the end of the Backrest with one hand and pull it slightly upwards.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user ’s manual for information about ordering replacement parts. Key No. Qty . Description Key No. Qty . Description Part List—Model No.
28 30 4 30 4 28 28 27 15 13 28 36 56 45 3 11 46 19 17 40 25 17 35 44 43 33 34 17 39 18 41 11 40 54 59 29 29 29 33 44 43 31 23 24 32 50 50 54 40 17 54 7 39 59 41 12 17 11 46 21 42 11 2 1 18 16 46 38 11.
Part No. 172417 R1200A Printed in China © 2000 ICON Health & Fitness, Inc. T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays).
デバイスImage IMBE53991の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Image IMBE53991をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImage IMBE53991の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Image IMBE53991の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Image IMBE53991で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Image IMBE53991を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImage IMBE53991の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Image IMBE53991に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImage IMBE53991デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。