ImpexメーカーCR 5の使用説明書/サービス説明書
ページ先へ移動 of 26
MARCY CORNER GYM CR 5 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www. im pe x-f it n e ss .
TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDW ARE IDENTIFIER.....…...
IMPORTA NT SA FETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain pr ecautions apply whenev er you operate a pi ece of exercise eq uipment. Be sure to r ead the entire manual before you assemble or operate y our machine.
3.
A SSEMBLY INSTRUCTI ON Tools Required A ssembling the Machine: Two Ad justable Wrenches and A llen Wrenches NOTE: It is strongly recommended tw o or people assembling this machine to avoid possible injury . STEP 1 (See Diagram 1) A.) Place the Right Base Frame ( #46) and Left Base Frame (#87) on the floor, at a r ight ang le to each other.
STEP 2 (See Diagram 2) A.) Attach the Rig ht Vertic al Beam (#21) to the R ight Base Frame ( #46). Secure i t with tw o M10 x 2 ¾” Car riag e Bolts (#17), ∅ ¾ ” W ashers (#6), and M10 Aircr aft Nuts (#5). B.) Attach the Rig ht Seat Support (#49) to the Rig ht Vertical Beam (#21).
STEP 3 (See Diagram 3) A.) Slide tw o ∅ 2 ½” Rubber Bumpers ( #58) onto tw o Chromed Guide R ods (#58). Insert the two Guide Rods into the holes on the R ight Base Fr ame (#46). Sli de the Selector Stem (#67) onto the two Guide R ods (#22). Sl ide the Selector Stem ov er the Selector Rod (#69).
DIAGRAM 3 7.
STEP 4 (See Diagram 4) A.) Attach the Front Press Base ( #97) to the Rig ht Base Frame (#46) . Secure it w ith a 9 ¼” Fr ont Press Axl e (#60), tw o ∅ ¾” W ashers (#6), and tw o M10 Airc raft Nuts (#5). B.) Attach the Front Press Fr ames (#63) to the Front Pr ess Base.
STEP 5 (See Diagram 5) A.) Attach the Butterfly Support Frame ( #18) to the front of Right Verti cal Beam (#21) . Attach the Butter Pulley Support (#74) to the back of Right Vert ical Beam. Ali gn the holes. Secur e them together w ith tw o M10 x 2 ¾” C arriag e Bolts (#17) , ∅ ¾” W ashers (#6), and M10 Airc raft Nuts (#5).
STEP 6 (See Diagram 6) A.) Attach the Vertical Pr ess Frame (#78) to the Rear Verti cal Beam (#50) . Secure it w ith a M10 x 4 7/8” Vertical Press Ax le (#81), tw o ∅ ¾” W ashers (#6), and tw o M10 x 1” Allen Bol ts (#56). B.) Place the Vertical Press Frame rest onto the ∅ 1 ½ ” Rubber Bumper (#83).
CABLE LOOP DIAGRAM 11.
STEP 7 (Upper Cable Loop & Diagram 7) A.) Attach the 108” Upper C able (#93) to the front openi ng on the Upper Fr ame (#8). Attach a Pulley (#79) to the opening . Secure it w ith one M 10 x 2 ½ ” Allen Bol t (#10), tw o Pulley Bushings ( #11), and one M10 Air craft Nut (#5).
DIAGRAM 7 13.
STEP 8 (See Butterfly Cable Loop & Diagram 8) A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Dr aw the Cable throug h the slot then to the open left Sw ivel Pulley Bracket (#72). B.) Attach a Pulley (#79) to the bracket.
DIAGRAM 8 15.
STEP 9 (See Front Press Cable Loop & Diagram 9) A.) Attach the 247” Front Press Cable ( #94) to the low er opening on the Leg Dev eloper ( #40). B.) Attach a Pulley (#79) to the opening. Secur e it w ith one M10 x 2 ½” All en Bolt (#10) , two Pulley Bushings ( #11), and one M10 Air craft Nut (#5) .
DIAGRAM 9 17.
STEP 10 (See Leg Press Cable Loop & Diagram 10) A.) Attach one end of the 82” Leg Pr ess Cable (#96) to the open slot on the back of the Leg Press Frame (#84) . Secure it w ith one M10 x 2 ½” Allen Bolt ( #10), two ∅ ¾” W ashers (#6), and one M10 Airc raft Nut (#5).
DIAGRAM 10 19.
STEP 11 (See Diagram 11) A.) Place a Seat Pad ( #29) onto the Left Seat Support (#92). Secur e it w ith two M 8 x 2 1/8” Allen Bolts (#25) and ∅ 5/8” W ashers (#24). B.) Attach a Backrest Boar d (#28) to the Left Vertical Beam (#77). Secure i t wi th two M 8 x 2 1/8” Allen Bolts ( #25) and ∅ 5/8” W ashers (#24).
STEP 12 (See Diagram 12) A.) Place a Seat Pad ( #29) onto the Rig ht Seat Support (#49) . Secure it w ith tw o M8 x 2 1/8” Allen Bolts ( #25) and ∅ 5/8” W ashers (#24). B.) Attach a Backrest Boar d (#28) to the Ri ght Verti cal Beam (#21). Secur e it w ith tw o M8 x 2 1/8” Allen Bolts ( #25) and ∅ 5/8” W ashers (#24).
STEP 13 (See Diagram 13) A.) Securely tig hten all the nuts and bolts pr eviousl y instal led. B.) Before putting the W eight Plates on, now mov e the machine to the corner of the room or place where you will use th e mach in e. C.) Lift up the Selector Rod and install one stack of 19 W eight Plates (#66).
PA RTS LIST KEY NO. DESCRIPTION Q’ty 1 Lat Bar Gr ip 2 2 Lat Bar 1 3 Chain 4 4 C-clip 6 5 M10 Aircraft Nut 52 6 ∅ ¾” W asher 82 7 Bracket 3 8 Upper Frame 1 9 1 ¾” Square End Cap 17 10 M10 x .
WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Low Pulley 40 54 68 80 93 105 116 127 138 Lat Pull 40 55 70 80 90 100 110 120 130 Butterfly 50 55 60 67 74 80 93 106 120 Leg Press 80 107.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and s ervic e conditions , f or a per iod of two years on the F ram e f r om the date of purchase.
デバイスImpex CR 5の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Impex CR 5をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImpex CR 5の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Impex CR 5の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Impex CR 5で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Impex CR 5を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImpex CR 5の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Impex CR 5に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImpex CR 5デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
