ImpexメーカーSM-4008の使用説明書/サービス説明書
ページ先へ移動 of 38
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model SM-4008 Retain This Manual for Reference 100806 OWNER'S MANUAL MARCY ® SMITH MACHINE SM-4008 IMPEX ® INC.
TABLE OF CONTENTS BEFORE YOU BE GIN..................................................................……………. 1 IMPORTANT SAFETY NOTI CES.................................................................… 2 SMITH MACHINE HARDWARE PACK….....
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine.
The warning labels shown here have been placed on th e Rear Base, and Bench Rear Stabilizer. If the labels are missing or illegible, please call custom er service at 1-800-888-8899 for replacements.
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4.
SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5.
SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6.
SMITH MACHINE HARDWARE PACK 7.
SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so.
STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Guide Rod (#24) into the hole on le ft Base Frame (#5). Secure it with one M8 x 2 3/8” Allen Bolt (#103), two Ø 5/8” Washer s (#106), and one M8 Aircraft Nut (#109).
10 STEP 3 (See Diagram 3).
A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear Base Frame (#8). C.) Attach the Lower Pulley Frame (#16) to the Middle Vertical Frame from rear. Attach the Foot Plate (#32) to the Middle Vertical Fram e from front.
12 STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#11) to the fr ont of Middle Vertical Frame (#9). Attach the Butterfly Pulley Bracket (#14) to the Middle Ve rtical Frame.
M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). B.) Attach the Butterfly Stopper (#31) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts (#58). C.) Attach the Backrest Board (#39) to Middle Vert ical Frame.
(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install the Left Butterfly (#12). B.) Insert two Swivel Pulley Brackets (#15) into the holes on the Butterfly Pulley Bracket (#14). Secure each Swivel Pulley Bracket with one M 12 x 5” Hex Bolt (#100), two Ø 1” Washer (#108), and one M12 Aircraft Nut (#111).
15 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of 113” Butterfly Cable (#45) to t he clip on Left Butterfly (#12). Draw the Cable to the left Swivel Pulley Bracket (#15).
B.) Attach a Pulley (#62) and two Cable Retainers (#78) to the Bracket. C.) Secure them with one M10 x 2” Allen Bolt ( #94), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). D.) Draw the Cable around the Pulley then downward. Attach an Angled Floating Pulley Bracket (#52) to the Cable.
A.) Attach the two Cross-over Swivel Pulley Br ackets (#10) to left and right Upper Side Frame (#7). Secure each Bracket with four M8 x 3/8” Allen Bolts (#101) and four Ø 5/8” Washers (#106). B.) Remove the U-shaped Connector, Big Washer, and Ball Stopper from one end of 266” Upper Cable (#47).
18 DIAGRAM 7-2.
19 UPPER CABLE (#47) LOOP DIAGRAM.
20 STEP 8 (See Diagram 8 & Cable Loop Diagram).
A.) Attach one end of the 97” Sliding Weight Post Cable (#46) to the Rear Upper Frame (#18). Secure it with one M10 x 2 3/8” Allen Bolt (#118), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). B.) Attach a Pulley (#62) to top holes on the tw o Double Floating Pulley Brackets (#33).
DIAGRAM 8 22.
STEP 9 (See Diagram 9) A.) Draw the 152” Lower Cable (#44) through t he opening on Foot Plate (#32) to the opening on bottom of Middle Vertical Frame (#9). B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#95), two Ø 1” x ½” Pulley Bushings (#57), and one M10 Aircraft Nut (#110).
DIAGRAM 9 24.
STEP 10 (See Diagram 10) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#28) in between the two Safety Stop Frames (#25). Align the holes. Insert the Weight Bar (#29) into the Safety Stop Fr ame from one end and through the Lifting Sleeve to the other Safety Stop Frame on the opposite side.
26.
SMITH MACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Front Left Vertical Frame 1 61 1 ½” Square End Cap 1 2 Front Right Vertical Frame 1 62 Pulley 20 3 Rear Left Vertical Frame 1 63 Small Pulley 4.
MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 28.
MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 29.
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.
STEP 2 (See Diagram 2) A.) Attach the Incline Support (#8) to the middle si de holes on the two Backrest Supports (#7). Secure it with one M10 x 6 7/8” Allen Bolt (#26), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Do not tighten the Nut and Bolt yet.
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#11) onto the Ba ckrest Supports (#7). Secure it with four M8 x 1 5/8” Allen Bolts (#32) and 5/8” Washers (#36). B.) Place the Seat Pad (#10) onto the two Seat Brackets (#4). Secure it with four M8 x 1 1/8” Allen Bolts (#31) and 5/8” Washers (#36).
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracke t on the Front Post (#2). Secure it with one M10 x 3” Allen Bolt (#29), two ¾” Washers (#35), and one M10 Aircraft Nut (#37). B.) Insert the Leg Developer Weight Post (#6) into the hole on Leg Developer.
33.
34 MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Post 1 3 Rear Stabilizer 1 4 Seat Bracket 2 5 Leg Developer 1 6 Leg Developer Weight Post 1 7 Backrest Support 2 8 I.
SM-4008 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 100% 10 lb. plate creates 10 lb. resistance Butterfly (both arms) 100% 10 lb. plate creates 5 lb. resistance Left Cross-Over 50% 10 lb. plate creates 5 lb resistance Right Cross-Over 50% 10 lb.
IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defec ts in workmanship and material, under normal use and service conditions, for a period of two years on t he Frame from the date of purchase. This warranty extends only to the original purchaser.
デバイスImpex SM-4008の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Impex SM-4008をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImpex SM-4008の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Impex SM-4008の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Impex SM-4008で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Impex SM-4008を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImpex SM-4008の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Impex SM-4008に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImpex SM-4008デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
