ImpexメーカーTR-2の使用説明書/サービス説明書
ページ先へ移動 of 22
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Warranty Ordering Parts Model TR-2 Retain This Manual for Reference 09-14-04 V4 OWNER'S MANUAL TECH ROD GYM TR-2 IMPEX INC.
WA RNING LA BELS PLA CEMENT The Warning Labels show n here have been placed on Low er Pulley Support Base. If this Labels are missing or illegible, please call Cu stomer Serv ice at 1-800-999- 8899 for free replacement. A pply the Label in the location shown.
TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDW ARE PACK……….....….
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assembl e or operate y our machine.
HA RDWA RE PA CK 3.
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches NOTE: It is strongly recommended tw o or more people assembling this machine to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Place the Base Platform (#8) on flat surface.
STEP 2 (See Diagram 2) A.) Attach the lower Rear Suppor t Frame (#2) to the Base Platform (#8). Secure it w ith one M10 x 4 7/8” Hex Bolt (#13), Ø ¾ ” W asher (#10), and M10 Air craft Nut (#16). D O NOT tighten the Nut and Bol t yet. B.) Insert bottom of Lower Pulley Support Base (#45) into the openings on the Base Platform.
STEP 3 (See Diagram 3) A.) Attach the High Pulley Support Bar (#18) to the Upper Fr ame (#17). Securel y tig hten with one Br acket (#19), tw o M10 x 2 3/8” Hex Bolts (#20) and two ؾ ” W ashers (#10). Cover the two Hex Bolts with tw o M10 Nut Caps (#21).
STEP 4 (See Diagram 4) A.) Attach the T ech Rod Set (#24) to the Rear Support Frame ( #2). Secure it with four Ø 1/4” x ¾” Philips Screw s (#25).
STEP 5 (See Diagram 5) A.) Place the Seat Pad (#27) onto the Seat Support (#26). Secure it w ith f our M6 x ¾” Hex Bolts (#6) and ؽ ” W ashers (#7). B.) Attach the Seat Support (#26) to the open bracket on the Vertic al Frame (#1) . Use a Lock Knob (#28) to securel y lock the Seat Suppor t in position.
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#30) to the front of Seat Support (#26). Secur e it w ith one M10 x 3” Hex Bolt (#12), tw o ؾ” W ashers (#10), and one M 10 Aircr aft Nut (#16). B.) Cover the Nut and Bolt w ith two M10 Nut C aps (#21).
STEP 7 (See Diagram 7) A.) Insert a Foam Tube (#32) halfway through the hol e on the Seat Support (#26) . Insert a Foam Tube halfway thr ough the hole on the Leg Dev eloper (#30) . B.) Push f our Foam Rolls (#33) onto the Foam Tubes from both ends. Plug four Foam Roll End Caps ( #34) into the ends of the T ubes.
STEP 8 (See Diagram 8 & Lat Bar Cable Loop Diagram) A.) Follow the below instructions to use the Lat Bar. B.) Attach a T ech Rod Cable (#11) to the Rig ht Pulley on the Extensi on Tube (#43). Attach the other end, L Shaped Connector ( #41) to one of the Tech Rod.
LA T BA R CA BLE LOOP DIA GRA M 12.
STEP 9 (See Diagram 9 & Leg Developer Cable Loop Diagram) A.) Follow the below instructions to use the Leg Dev eloper. B.) Detach the end of the Lat Bar Cables from the End Hooks on Tech Rod Cables and hook the Cable ends onto the Cabl e Hangers on the si de of the Vertical Fr ame.
LEG DEVELOPER CA BLE LOOP DIA GRA M 14.
STEP 10 (See Diagram10 & Cable Loop Diagram) A.) Follow the below instructions w hen doing bench press or butterfly ex ercises. B.) Attach the ends of Lat Bar Cables (#35) and Leg Dev e loper Cables (#36) onto the Cable Hang ers (#42) on the side of the Vertical Fr ame.
TECH ROD CA BLE LOOP DIA GRA M 16.
EXPLODED DIA GRA M 17.
TECH ROD RESISTANCE CHART TECH ROD (each side) Bench Press/ Butterfly LA T CA BLE LEG DEVELOPER CA BLE 5LB 5 LB 5 LB 3 LB 10LB 10 LB 10 LB 8 LB 10LB 10 LB 10 LB 8 LB 25LB 25 LB 25 LB 20 LB 50LB 50 LB 50 LB 35 LB TOTAL 100LB 100LB 74LB *Numbers are approximate.
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Vertical Frame 1 2 Rear Support Fr ame 1 3 M8 x 5/8” Allen Bolt 2 4 Ø 5/8” W asher 3 5 Back Pad 1 6 M6 x ¾ ” Hex Bolt 8 7 Ø ½” W asher 8 8 Base Plat.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this produc t to be free f rom def ects in work m anship and mater ial, under norm al use and servic e conditions, f or a period of two y ears on the F ram e f rom the date of pur chase.
デバイスImpex TR-2の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Impex TR-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImpex TR-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Impex TR-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Impex TR-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Impex TR-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImpex TR-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Impex TR-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImpex TR-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。