ImpexメーカーWM 1403の使用説明書/サービス説明書
ページ先へ移動 of 22
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Resistance Chart Warranty Ordering Parts Model WM 1403 Retain This Manual for Reference 06-19-02 OWNER'S MANUAL POWERHOUSE HOME GYM WM 1403 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD.
TA BLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFET Y NOTICE...................................................................……….. 2 HARDW ARE IDENTIFIER.
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine.
3.
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches, two Allen Wrenches, and one Flat Head Screw driver. NOTE: It is strongly recommended this machine to be assembled by tw o or more people to avoid possible inj ury.
STEP 2 (See Diagram 2) A.) Attach the Front Upper Vertical Beam (#5) to the Front Low er Vertical Beam (#82) . Secure it with tw o M10 x 2 ½” Carri age Bolts ( #42), ∅ ¾” W ashers (#53), and M10 Air craft Nuts (#55).
STEP 3 (See Diagram 3) A.) Attach the Front Lower Verti cal Beam (#82) , both Left and Right Storag e Posts (#15) & (#16) to the Main Base Frame ( #6). Secure them together wi th two M 10 x 3” C arriag e Bolts (#73), ∅ ¾” W ashers (#53) and M10 Air craft Nuts (#55).
STEP 4 (See Diagram 4) A.) Slide the W eight Hol der (#2) onto the R ear Verti cal Beam (#1) from the top. B.) Attach the rear end of Upper Frame (#4) to the R ear Upper Ver tical Beam ( #1). Secure the upper hole w ith a Small Bracket (#20), M 10 x 2 3/8” Al len Bolt ( #46), and ∅ ¾” W asher (#53).
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#12) to the Upper Frame ( #4). Secure it w ith one 5 7/8” Axle (#60), tw o ∅ 1” Axle W ashers (#64), and two M10 Ai rcraft Nuts (#55) . Do not ov er tighten the nuts. Make sure the Base is abl e to swiv el.
STEP 6 (See Diagram 6) A.) Attach a Rubber Bumper (#38) to the Leg Dev eloper (#11) . Secure it w ith one M6 x 5/8” Philips Screw (#41). Attach the Leg Developer to the bracket on the Main Seat Support (#7). Secure it w ith one M10 x 3” All en Bolt (#44), tw o ∅ ¾” W ashers (#53), and one M 10 Aircraft Nut (#55).
STEP 7 (See Diagram 7) A.) Insert the axle on the Ri ght Butterfly Arm (#14) through the r ight piv ot hole on the Front Press Base (#12). Sl ide a ∅ 1 ½” W asher (#54) and Ri ng Cap ( #68) onto the ax le. Secure the Cap w ith a M6 x 1 5/8” Hex Bolt (#63) and M6 Aircr a f t Nut (#56).
Cable Loop Diagram 11.
STEP 8 (See Cable Loop Diagram & Diagram 8) A.) Attach the 129.9” Upper Cable (#31) to the open bracket in the front of Upper Frame ( #4). Attach a Pulley (#28) to the open bracket. Secur e it w ith one M10 x 1 ¾” Allen Bolt (#45), two ∅ ¾ ” W ashers (#53), and one M10 Airc raft Nut (#55).
D i a g r a m 8 12.
STEP 9 (See Cable Loop Diagram & Diagram 9) A.) Attach one end of the 116” Butterfly C able (#29) to the Hook on the Rig ht Butterfly Ar m (#14).
STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Insert the 110.2” Lower Cable (#30) through the opening on bottom of the Leg Devel oper (#11). Attach a Pul ley (#28) to the opening . Secure it with one M10 x 2 3/8” Allen Bol t (#46), tw o ∅ 7/8” Pulley Bushing s (#51), and one M10 Aircr aft Nut (#55).
DIAGRAM 10 16 STEP 11 (See Diagram 11).
A.) Attach a Butterfly Arm Pad (#24) to the R ight Butter fly Arm ( #14). Secure it w ith two M8 x 2” Allen Bol ts (#74) and ∅ 5/8” W ashers (#52). Repeat the same pr ocedure to install the other side. B.) Attach the Backrest Board (#23) to the Front Upper Vertical Frame (#5).
STEP 12 (See Diagram 12) A.) Insert two Foam Roll Tubes (#27) halfway through the holes on the Main Seat Suppor t (#7) and Leg Dev eloper (#11). Push four Foam Rolls ( #26) onto the tubes. B.) Connect the Arm Curl Handl e (#70) to the Low er Cable wi th two C -clips ( #57) and one Long Chain (#79) .
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Rear Upper Vertic al Beam 1 2 W eight Holder 1 3 Rear Stabilizer 1 4 Upper Fram e 1 5 Front Upper Ver tical Beam 1 6 Main Base Fram e 1 7 Main Seat Support 1 8 .
WEIGHT RESISTANCE CHART The following chart shows the approxim ate weight resistance ratio at each station. Weight resistance shows for the butterfly station is for each butterfly arm. The actual resistance at each station m ay vary due to friction and differences in each individual plate .
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and s ervic e conditions , f or a per iod of two years on the F ram e f r om the date of purchase.
デバイスImpex WM 1403の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Impex WM 1403をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはImpex WM 1403の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Impex WM 1403の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Impex WM 1403で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Impex WM 1403を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はImpex WM 1403の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Impex WM 1403に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちImpex WM 1403デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
