a/d/s/メーカー246ixの使用説明書/サービス説明書
ページ先へ移動 of 18
analog and digital systems 245ix 246ix owner's manual.
table of contents introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 about this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
featur es Molded woofer basket - The backbone of any good woofer is its basket. It provides the pr oper alignment and support structure for the magnet and moving parts while the very thin braces guarantee a minimum of early reflections of f the basket that would be ordinarily transmitted as sonic colorations through the cone.
When removing or installing the grilles, be car eful not to brush the woofer's rubber surround or the tweeter's dome with the edge of the grille. Cutting or tearing the surround or dome will destr oy the unit. Never run wires outside or beneath the vehicle wher e they can be snagged by road hazards or the moving parts of the vehicle.
cr ossover featur es and connections Bi-amp/Parallel switch Select the Bi-amp position if you intend on driving the woofers and tweeters with separate amplifiers (four channels). Select the Parallel position if you intend on driving the woofers and tweeters with the same amplifier (two channels).
Y ou may also Bi-wire the system by connecting the woofer input terminals to the amplifier and connect ing the tweeter input terminals to the same amplifier with another set of speaker wires. This is sometimes done to allow a specific high frequency or low fr equency cabling to be used for the two separate signal paths.
speaker installation Woofer installation The woofer will fit into many standard factory mounting locations using the existing mounting holes in the automobile. Remove the trim panels and inspect the installation locations before you cut and drill the holes requir ed to mount the woofer .
Install the tweeter into the extension housing by first threading the tweeter wir es through the extension housing and then installing the tweeter into the mounting slots of the housing and turn the tweeter counterclockwise to lock the tweeter in place.
The tweeter is mounted at and angled relative to the woofer . Before final woofer mounting, rotate the woofer so that the tweeter is pointed in the desired dir ection, typically towards the listener’ s ear location. Surface mount The preparation of the mounting surface for the tweeter involves drilling thr ee holes.
Check the intended installation site to be sure that there is suf ficient depth behind the mounting surface for the rear cup and mounting screws. The minimum depth r equired behind the back of the mounting surface is 1" (25 mm). The front cup mounts into the mounting through a 1-7/8" (48 mm) diameter hole.
NOTE: The tweeter grill can be easily removed for coaxial applications, or to facilitate mounting the tweeter behind an existing factory grill. Use the supplied black butyl material to attach the tweeter grill for all other applications.
Align the mounting holes in the bottom half of the crossover unit with the holes you have drilled at the installation site. Pass the four #6 x 1 1/4" screws thr ough the holes in the crossover unit, and tighten them until the assembly is firmly in place.
bi-amplified connections to cr ossover Connections from the cr ossover to the woofer and tweeter are the same as the normal wiring method. Connect the amplifier you have chosen for the tweeter to the “T weeter In” terminals input. Connect the woofer amplifier to the “Woofer In” terminals.
bi-wir e connections to cr ossover Connections from the cr ossover to the woofer and tweeter are the same as the normal wiring method. Connect the amplifier to the tweeter input terminals with one run of wire. Connect the amplifier to the woofer input terminals with another run of wire.
tr oubleshooting Symptom Probable Cause Remedy No output Source or amplifier not turned on. Check source or amplifier and fix as requir ed. Audio input not connected or no output from sour ce. Check RCA connections and signal integrity , fix or replace as r equired.
specifications 245ix 246ix Frequency r esponse 90Hz–22kHz 70Hz–22kHz Sensitivity 91dB 91dB Impedance 4 ohms 4 ohms Recommended amplifier power 45–100 watts 45–150 watts Mounting depth (woofer) 2-1/2 inches (6.35 cm) 2-5/8 inches (6.67 cm) RMSE-free 1.
warranty information LIMITED TWO YEAR CONSUMER W ARRANTY Directed Electr onics, Inc. promises to the original purchaser , to replace this product should it pr ove to be defective in workmanship or mat.
a © 2004 Directed Electronics, Inc. All rights reserved G39206.1 1 04-04.
デバイスa/d/s/ 246ixの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
a/d/s/ 246ixをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはa/d/s/ 246ixの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。a/d/s/ 246ixの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。a/d/s/ 246ixで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
a/d/s/ 246ixを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はa/d/s/ 246ixの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、a/d/s/ 246ixに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちa/d/s/ 246ixデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。