IntegraメーカーDTR-6.2の使用説明書/サービス説明書
ページ先へ移動 of 64
Contents Thank you f or purchasing the A V Receiv er . Please read this m anual thoroughly bef ore making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum perf or m ance and listening enjoyment from y our ne w A V Receiver .
2 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to.
3 1. Warranty Claim You can find the serial number on the rear panel of this unit. In case of warranty claim, please report this number. 2. Recording Copyright Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder.
4 Contents Bef ore using Important Safeguards ......................................... 2 Precautions ......................................................... 3 Contents .............................................................. 4 Features ......
5 Contents 2. Input Setup menu ..................................................... 38 2-1. Audio Setup sub-menu ............................................ 38 2-2. V ideo Setup sub-menu ............................................ 39 2-3. Listening Mode Preset sub-menu .
6 Features Amplifier Features ■ 100 Watts minimum of continuous RMS power to each of the five channels into 8 Ω from 20 Hz to 20 kHz with no more than 0.
7 Installing the remote controller batteries 1. Remove the battery compartment cover by pressing and sliding the cover. 2. Insert two AA (R6 or UM-3) batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative (–) symbols) inside the battery compartment.
8 Standby/On Standby Power On O f f Phones Video 1 Video 3 DVD Video 2 Video 4 Audio Selector Bass Treble Master Volume Smart Scan Navigator Rec Out Zone 2 Zone 2 Level CH Level Dimmer Display Tuning .
9 Front panel facilities For operational instructions, see page indicated in brackets [ ]. Power switch [21] Turns on and off the main power supply for the DTR-6.2. Standby indicator [7, 21] Lights when the DTR-6.2 is in the standby state and flashes when a signal is received from the remote controller.
10 HOME THEA TER CONTROLLER RC - 441M J I H G F E D C B A 0 8 9 1 K 2 3 4 5 6 7 Remote contr oller SEND/LEARN indicator [50, 54, 56] This indicator acts as a guide when commands are programmed into or sent by the remote controller. It also warns the user when an error is made or battery power is low.
11 Remote controller ZONE 2/SEARCH/ENTER button ZONE 2: When in the RCVR mode, press this button to perform operations on the remote zone (Zone 2). [45] SEARCH: When in the DVD mode, for finding the specific section on a disc where you want to start playback.
12 Default setting Input source Digital input Component video Multichannel DVD COAX 1 INPUT 1 Yes Video 1 COAX 2 INPUT 2 No Video 2 ---- INPUT 1 No Video 3 OPT 2 INPUT 1 No Video 4 ---- INPUT 1 No Tape ---- No FM AM Phono ---- No CD OPT 1 No IN OUT 6 OHMS MIN.
13 P B P R Y REMOTE CONTROL IN P OUTPUT 75 AM ANTENNA Y COMPON E VIDEO 1 DVD IN OUT IN O MONITOR OUT A B 12 V TRIGGER CENTER SUB WOOFER FRONT SURR SUBWOOFER OPTICAL COAXIAL 1 2 12 PRE OUT MULTI CHANNEL INPUT DIGITAL INPUT L R OUT IN PHONO TA P E CD GND L R FM 2.
14 IN P B P R Y INPUT 1 INPUT 2 OUTPUT P B P R Y P B P R Y COMPONENT VIDEO L VIDEO 1 VIDEO 2 DVD VIDEO 4 IN OUT IN OUT IN IN IN MONITOR OUT VIDEO 3 ZONE 2 PRE OUT VIDEO S VIDEO CENTER SUB WOOFER OPTICAL COAXIAL 1 2 12 U T DIGIT AL INPUT IN T APE R IR RS 232 OUT 8.
15 Connections 7. Connecting a DVD recorder or other digital video recording device (VIDEO 1) If the device is equipped with an S video output terminal, connect it to the S VIDEO 1 IN terminal with an S video cable.
16 Connections AC OUTLETS AC 120 V 60 Hz SWITCHED TOTAL 120 W 1 A MAX. Cautions regarding the AC OUTLETS connectors The DTR-6.2 is supplied with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the DTR-6.
17 Connecting speaker s Connections Connect to devices with multichannel output By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1 channel output. So, be sure to prepare a cable that can properly connect the DTR-6.
18 Connecting a subwoofer Use the PRE OUT SUBWOOFER jack to connect a subwoofer with a built-in power amplifier. If your subwoofer does not have a built-in amplifier, connect an amplifier to the PRE OUT SUBWOOFER jack and the subwoofer to the amplifier.
19 Listening to m usic in the remote zone When using the ZONE 2 OUT terminals The ZONE 2 OUT terminal is a constant output. Connect to the LINE input of the amplifier (CD, tape, etc.). Adjust the volume with the amplifier connected to the ZONE 2 OUT terminal.
20 IR IN DTR-6.2 In the cobinet Remote Controller Connecting block IR Receiver : Signal flow IR IN IR OUT Connecting block IR Receiver DTR-6.2 IR Emitter Remote Controller other component : Signal flow IN IR OUT : Signal flow IR Emitter Remote control sensor other component DTR-6.
21 • The DTR-6.2 is shipped with the main power (Power) switch in the on position ( ON ). When the power cord is plugged in for the first time, the DTR-6.2 will automatically enter the standby state and the Standby indicator will light (same condition after step 2 below).
22 FM 75 AM ANTENNA Strip away the insulation from the end of the cable, then fully insert the stripped end of the cable. (Indoor) AM loop antenna Connecting antennas Connecting the AM antenna cable 1. Press down the lever. 2. Insert the wire into the hole.
23 FM 75 AM ANTENNA FM 75 AM ANTENNA Connecting antennas Outdoor antenna (Indoor) AM loop antenna To TV (or VCR) To receiver Connecting an AM outdoor antenna An outdoor antenna will be more effective if it is stretched horizontally above a window or outside.
24 Speaker setup After you have installed the DTR-6.2, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout.
25 Speaker setup Speaker Distance submenu This submenu provides settings that tell the DTR-6.2 how far away your speakers are located from the listening position so that it can provide the optimum sound space. If you are continuing from setting the speaker configuration and are still in the setting mode, skip directly to step 2.
26 Speaker setup About the other settings The factory settings for your DTR-6.2 are given in the table on page 12. If you connect your system in accordance with these factory settings, there is no need to change them. However, if you do not, you will need to change the settings that do not match.
27 Listening to Radio Br oadcasts One of the features of the DTR-6.2 that is most frequently used is its ability to play FM and AM broadcast radio stations. The DTR-6.2 provides a number of listening modes perfect for listening to the radio and getting the most out of your audio system.
28 Listening to Radio Broadcasts Erasing a preset radio station 1. Press the AM or FM button and press the Preset / button to select the preset radio station that you want erase (see above). 2. Press the Preset Memory button. “ Preset In? ” appears.
29 Enjo ying m usic or videos with the DTR-6.2 Though the DTR-6.2 is often used to listen to the radio, it does not show you its true ability until it is used to play music or watch videos, DVDs, and the like.
30 Enjoying music or videos with the DTR-6.2 Switching the display While listening to or watching an input source, you can display the information regarding the type of source and signal being input by pressing the button on the DTR-6.2 or the DISPLAY button on the remote controller.
31 Changing the audio mode Press the Audio Selector button on the front panel (or AUDIO button on the remote controller) to change the audio mode. Each time the button is pressed, the mode changes from “ AUTO ” → “ Multich ” → “ Analog ” and back to “ AUTO.
32 Using listening mode Listening modes Stereo This mode has all input sounds output from the left and right front speakers. Direct This mode delivers pure sound with minimum sound quality adjustment and filtration.
33 Using listening mode Changing the listening mode To change the listening mode during playback, press the listening mode buttons on the remote controller.
34 Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER|Quit:|SETUP| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration |ENTER|Quit:|SETUP| 1-1.Speaker Config a.Subwoofer :Yes b.Front :Large c.
35 Setting procedures and button operations Remote controller DTR-6.2 Main menu Display menu (display OSD menu) Select item Enter selected item Menu Select item Enter selected item Submenu Select item Set parameter Other Move up one level Exit OSD menu 1.
36 Setup menus Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.Bass Peak Level D| 1-1.Speaker Config a.Subwoofer :Yes b.Front :Large c.
37 Setup menus 1-3. Level Calibration sub-menu 1-2. Speaker Distance sub-menu Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.
38 Setup menus Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 2.Input Setup Input:DVD 1.Audio Setup 2.Video Setup 3.Listening Mode Preset 4.IntelliVolume 5.12V trigger |ENTER|Quit:|SETUP| Current Input Source 2.
39 Setup menus 2-2. Video Setup sub-menu Input source selected Component video input DVD INPUT 1 Video 1 INPUT 2 Video 2 INPUT 1 Video 3 INPUT 1 Video 4 INPUT 1 a. Component Video If a component is connected to the one of the COMPONENT VIDEO inputs (1 or 2), then that input must be set here.
40 Setup menus 2-4. IntelliVolume sub-menu Input source signal (display) Analog/PCM Source Digital Format Type of media Tape, CD, DVD, Record, Tuner Digital satellite broadcast, DVD Video (PCM), LD (P.
41 Setup menus Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 3.Listening Mode Setup 1.Stereo Setup 2.Surround Setup 3.Orchestra Setup 4.Unplugged Setup 5.Studio-Mix Setup 6.TV Logic Setup 7.All Ch Stereo Setup |ENTER|Quit:|SETUP| 3.
42 4-4. IR IN Setup sub-menu 4-2. Headphones Level sub-menu Setup menus Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 4.Preference 1.Volume Setup 2.Headphones Level 3.DTS LFE Level Setup 4.Powered Zone2 Setup |ENTER| Quit:|OSD| 4-2.
43 5. OSD Setup menu This menu provides settings for you to customize the on-screen display (OSD) for the DTR-6.2 by setting different colors or positions for its display. Setup menus Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.
44 3. Start recording at the recording device connected to the TAPE OUT jacks. You can press the Rec Out button to display which input source is selected for recording. When “ Rec Sel : Off ” is displayed, no signal is output for recording. Notes: • You cannot use the Rec Out selector to record video signals.
45 Enjo ying m usic in the remote zone Notes: • If you wish to use the remote controller from a separate room or other location where the signals will not reach the DTR-6.2, you will need to purchase a commercially available remote control sensor and emitter (see page 20).
46 Using remote contr oller Overview The RC-441M remote controller is a useful tool to help you operate the components of your home theater. To do so, first press the Mode button that corresponds to the device you wish to control. Then simply press the desired operation button and the component will operate accordingly.
47 Controlling an Integra/Onkyo CD player The z connector of the Integra/Onkyo compact disc player must be connected to the DTR-6.2 (see page 16). 1. Press the CD MODE button.
48 Using remote controller Controlling an Integra/Onkyo DVD player The z connector of the Integra/Onkyo DVD player must be connected to the DTR-6.2 (see page 16). 1. Press the DVD MODE button. The DVD MODE button lights green. 2. Press the desired operation button.
49 Controlling an Integra/Onkyo MD recorder The z connector of the Integra/Onkyo MD recorder must be connected to the DTR-6.2 (see page 16). 1. Press the MD MODE button.
50 Learning a pre-pr ogramming code HOME THEA TER CONTROLLER RC - 441M DISPLAY SEND/LEARN indicator Numeric keys Buttons that can be pre- programmed Learning a pre-programming code By learning a pre-programming code, you can make the RC-441M remote controller able to operate a product from another brand.
51 Pre-programmong codes Learning a pre-programming code CABLE BRAND SETTING No. GENERAL INSTRUMENTS 500 GEMINI 501 HAMLIN 502, 503, 504, 505 JERROLD 500, 506, 507, 508, 509, 510, 511, 512, 513, 514 M.
52 Operating y our pr ogrammed remote contr oller Numeric keys HOME THEA TER CONTROLLER RC - 441M ON STDBY ENTER MUTING CABLE MODE CH VOL CABLE MODE (Cable Mode) 1. Press the CABLE MODE button. The CABLE button lights green. 2. Press the desired operation button.
53 Operating your programmed remote controller Numeric keys Numeric keys Video cassette recorder operation buttons HOME THEA TER CONTROLLER RC - 441M ON STDBY TV MODE ENTER MUTING TV/VCR CH VOL HOME THEA TER CONTROLLER RC - 441M ON STDBY VCR MODE MUTING TV/VCR CH VOL TV MODE (TV Mode) 1.
54 Pr ogramming the commands of remote contr oller s f or other devices into the remote contr oller 5 to 15 cm (2 to 6 inches) Buttons that cannot be programmed.
55 Programming the commands of remote controllers for other devices into the remote controller 4. Press and hold down the button (that corresponds to the command you are programming) on the remote controller of the other device until the SEND/LEARN lamp on the remote controller flashes twice.
56 Programming the commands of remote controllers for other devices into the remote controller HOME THEA TER CONTROLLER RC - 441M ENTER HOME THEA TER CONTROLLER RC - 441M ENTER SEND/LEARN indicator MODE buttons SEND/LEARN indicator MODE buttons Erasing the programmed command from one button You can only erase memorized commands and not preset ones.
57 Using a Macr o function Programming a Macro function You can program a different macro into the MODE MACRO button for each of the eight MODE buttons. The macro is then executed by pressing the appropriate MODE button and then pressing the MODE MACRO button.
58 Using a Macro function Programming the Direct Macro function With the direct macro function, you can program a series of button operations as a macro into the DIRECT MACRO button so the macro can be executed with just one touch. Note that for the direct macro function, only one macro can be programmed.
59 Using a Macro function Erasing a macro from the MODE MACRO button 1. Press and hold down the desired MODE button, press the MODE MACRO button, and then release both buttons. When you press the MODE button, it lights green and the SEND/LEARN indicator lights.
60 Using a Macro function Erasing all commands and macros that have been programmed This procedure will erase all the commands and macros that you have programmed into the remote controller and return it to its default settings. This operation will not affect the preset settings of the remote controller.
61 Specifications AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 100 W per channel min. RMS at 8 Ω , 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion. 125 W min. RMS at 6 Ω , 2 channels driven from 1 kHz with no more than 0.
62 FM/AM TUNER AM stations cannot be received. • AM loop antenna is not connected. ➞ Connect the included AM loop antenna to the AM antenna terminals. Buzzing noise on AM stations (particularly noticeable at night or with weak stations). • Noise from electrical apparatus such as fluorescent lamp.
63 Troubleshooting guide VIDEO and AUDIO Desired picture does not appear. • Improper connection. ➞ Check the connection again. Insert the plugs and connectors completely. No OSD Menu display. • Improper connection. ➞ Check connections. • OSD Menu is displayed when monitor is connected to VIDEO or S VIDEO of MONITOR OUT.
D0104-2 E Integra Division of ONKYO U.S.A. CORPORA TION 18 Park W ay, Upper Saddle River , N.J. 07458, U.S.A. T el: 201-785-2600 Fax: 201-785-2650 E-mail: integra@onkyousa.
デバイスIntegra DTR-6.2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Integra DTR-6.2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIntegra DTR-6.2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Integra DTR-6.2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Integra DTR-6.2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Integra DTR-6.2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIntegra DTR-6.2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Integra DTR-6.2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIntegra DTR-6.2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
