InvacareメーカーInfinity Back Supportの使用説明書/サービス説明書
ページ先へ移動 of 16
INFINITY BA CK SUPPOR TS Assembly , Installation and Operation Instructions.
2 W ARNING THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY AN AUTHORIZED DEALER OR QUALIFIED SER VICE TECHNICIAN. DO NOT INST ALL OR USE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERST ANDING THIS MANUAL.
3 SAFETY SUMMARY SAFETY SUMMAR Y S A F E T Y S U M M A R Y NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction. INST ALLA TION W ARNINGS Stabilize from the ground up. A stable base, pelvis and footrests are requirements for any torso positioning system.
4 SAFETY SUMMARY ST ABILITY W ARNINGS (CONTINUED) AL W A YS make sure wheelchair is stable BEFORE reclining the back system. Rear wheels may have to be repositioned rearwar d depending on the degree of recline. AL W A YS ensure stability BEFORE using maximum amount of recline.
5 INSTALLATION/ADJUSTMENT OVERVIEW (FIGURE 1) W ARNING For proper installation of the Infinity Back and to reduce the risk o f pressure sores, the adjustment procedures in this manual MUST be per formed in the following or der: 1. Adjusting the Mounting Hardware 2 .
6 PROCEDURE 1 PREP ARING WHEELCHAIR P R E P A R I N G W H E E L C H A I R This Procedure includes the following: Installing/Removing Cane Clamps Installing Inserts INSTALLING/REMOVING CANE CLAMPS (FIGURE 1) NOTE: Refer to the INST ALLA TION AND ST ABILITY W ARNINGS in the SAFETY SUMMAR Y of this manual.
7 This Procedure includes the following: Installing/Removing the Lateral Supports Installing/Removing Cushions Adjusting the Mounting Hardware PREP ARING THE INFINITY BACK FOR INST ALLA TION PROCEDURE.
8 PREP ARING THE INFINITY BACK FOR INST ALLA TION T op Flap Bottom Flap Fastening Strips (Attach to Back Panel) Infinity Back Fastening Strips Elastic Strip REMOVING. 1 . Remove the back cushion from the back panel(s). Refer to INST ALLING/REMOVING BACK CUSH- ION in this procedure of the manual.
9 PREP ARING THE INFINITY BACK FOR INST ALLA TION 4 . If necessary , loosen, but do not remove the two (2) mounting screws securing each upper width bracket to the back frame.
10 INST ALLING/REMOVING THE INFINITY BACK INSTALLING/REMOVING THE INFINITY BACK (FIGURE 1) NOTE: Refer to the INST ALLA TION AND ST ABILITY W ARNINGS in the SAFETY SUMMARY of this manual. Installing the Infinity Back 1. Ensure the four (4) cane clamps are securely installed on the wheelchair frame.
11 ADJUSTING THE INFINITY BACK PROCEDURE 4 ADJUSTING THE HINGE/ANGLE (DUALFLEX ONLY) NOTE: Refer to the INST ALLA TION AND ST ABILITY W ARNINGS in the SAFETY SUMMAR Y of this manual.
12 ADJUSTING THE INFINITY BACK PROCEDURE 4 A D J U S T I N G Converting Fixed Angle Hinges to Dynamic Flex Hinges (FIGURE 3) 1. Remove the four (4) short mounting screws securing the hinge to the back panels. NOTE: Save the short mounting screws for future conversion to fixed angle hinges.
13 PROCEDURE 4 ADJUSTING THE INFINITY BACK A D J U S T I N G 6. Slide one (1) lateral support to the desired location. 7 . Visually inspect the adjustment slot to find proper lo- cation for the curved washer . 8 . Remove one (1) mounting screw , tooth lock washer and curved washer .
14 PROCEDURE 5 FIGURE 1 - REMOVING/INST ALLING BACK CUSHION FOAM T op of Back Cover Back Cushion Foam Bottom Flap INSTALLING/REMOVING CUSHION FOAM NOTE: Refer to the INST ALLA TION AND ST ABILITY W ARNINGS in the SAFETY SUMMARY of this manual. Installing/Removing Back Cushion Foam (FIGURE 1) INSTALLING.
15 PROCEDURE 5 M A I N T E N A N C E MAINTENANCE Installing/Removing Adjustable Positioning Pad (UNIBACK ONLY) (FIGURE 3) INSTALLING. 1 . Lift the top flap up and pull the bottom flap down on the back cushion cover . 2 . Grasp the cushion and pull upwards to remove the cushion from the back.
Form No. 99-104 Part No. 1077719 Rev. A. (1)-3/99 Printed in U.S.A. INV ACARE CORPORA TION l ONE INV ACARE W A Y l P .O. Box 4028 l Elyria, Ohio 44036-2125 Phone 1-(800)-333-6900 l T echnical Support .
デバイスInvacare Infinity Back Supportの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Invacare Infinity Back Supportをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはInvacare Infinity Back Supportの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Invacare Infinity Back Supportの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Invacare Infinity Back Supportで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Invacare Infinity Back Supportを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はInvacare Infinity Back Supportの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Invacare Infinity Back Supportに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちInvacare Infinity Back Supportデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。