InvacareメーカーOCMK78の使用説明書/サービス説明書
ページ先へ移動 of 16
On Chair Mounting Kit Assembly , Installation and Operating Instructions Model Nos. OCMK01 and OCMK78 SA VE THESE INSTRUCTIONS NOTE: Check all parts for shipping damage.
2 INSTALLATION OF THE ON CHAIR MOUNTING KIT BACK MOUNTING HARDWARE (FIGURE 1) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2 twist release clamps.
3 Twist Release Clamps. DETAIL "B" Mark FRONT OF WHEELCHAIR Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Upper J Brackets (Top Edge) Lower .
4 INSTALLING THE BACK L BRACKETS (FIGURE 2) NOTE: When mounting the L brackets to the wood backed ContourU cushion the L brackets may be reversed to allow for greater seat depth adjustments as shown in DETAIL A of FIGURE 2.
5 INSTALLING THE BACK J BRACKETS (FIGURE 3) 1. Position the ContourU back between the back canes to determine the approximate mounting position of the J brackets to obtain the desired depth. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 3.
6 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM BACK (FIGURE 4) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 4. 2. Position the two (2) lower J brackets securely into the two (2) fixed release clamps as shown in FIGURE 4.
7 ADJUSTING THE CONTOUR U BACK DEPTH (FIGURE 5) NOTE: There are six (6) depth adjustments avail- able on the ContourU with a pan back. NOTE: There are twelve (12) depth adjustments available on the ContourU with a wood back.
8 ADJUSTING THE CONTOUR U SEATING SYSTEM BACK ANGLE (FIGURE 6) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same depth. Refer to ADJUSTING THE CONT OUR U SEA TING SYSTEM BACK DEPTH in this instruction sheet. NOTE: The back to seat angle is adjusted by repositioning the top and/or the bottom J brackets.
9 INSTALLATION OF ON CHAIR MOUNTING KIT SEAT MOUNTING HARDWARE (FIGURE 7) NOTE: Refer to GENERAL and INSTALLATION WARNINGS in the SAFETY SUMMARY in this instruction sheet. NOTE: The wheelchair hardware consists of two (2) fixed release clamps and two (2) twist release clamps.
10 Twist Release Clamps. DETAIL "B" Mark Fixed Release Clamp Internal Threaded Mounting Screw Washer Mounting Screw DETAIL "A" Front J Brackets (Front Edge) Rear J Brackets (Rear E.
11 INSTALLING THE SEAT L BRACKETS (FIGURE 8) NOTE: When mounting the L brackets to the wood backed ContourU seat the L brackets may be reversed to allow for a wider range of seat height adjustments and shown in DETAIL A of FIGURE 8.
12 INSTALLING THE SEAT J BRACKETS (FIGURE 9) 1. Position the ContourU seat between the seat rails to determine the approximate mounting position of the J brackets to ensure the appropriate height setting. 2. Align two (2) of four (4) mounting holes of the J bracket with two (2) of five (5) mounting holes on the L bracket as shown in FIGURE 9.
13 INSTALLING/REMOVING THE CONTOUR U SEATING SYSTEM SEAT (FIGURE 10) Installing 1. Ensure that the twist release clamps are in the OPEN position as shown in DETAIL A of FIGURE 10. 2. Position the rear J brackets securely into the fixed release clamps as shown in FIGURE 10.
14 ADJUSTING THE CONTOUR U SEAT HEIGHT (FIGURE 11) NOTE: There are six (6) height adjustments avail- able on the ContourU seat with a seat pan. NOTE: There are twelve (12) height adjustments available on the ContourU seat with a wood back.
15 ADJUSTING THE CONTOUR U SEATING SYSTEM SEAT ANGLE (FIGURE 12) NOTE: Before performing this procedure all four (4) J brackets must be adjusted to the same height. Refer to ADJUSTING THE CONTOUR U SEAT HEIGHT in this instruction sheet. NOTE: The seat angle is adjusted by repositioning the front and/or the rear J brackets.
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare is a registered trademark of Elyria, Ohio USA Mississauga Ontario Invacare Corporation. 44036-2125 L4Z4G4 Canada Yes, you can. is a trademark of Invacare 800-333-6900 800-668-5324 Corporation.
デバイスInvacare OCMK78の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Invacare OCMK78をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはInvacare OCMK78の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Invacare OCMK78の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Invacare OCMK78で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Invacare OCMK78を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はInvacare OCMK78の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Invacare OCMK78に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちInvacare OCMK78デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。