InvacareメーカーRanger II250 SERIESの使用説明書/サービス説明書
ページ先へ移動 of 84
Ranger II Storm Series ® Wheelchair s MWD/FWD Ranger II B ASIC Ranger II ST ANDARD Ranger II JR Ranger II 250 SERIES Ser vice Man ual DEALER: THIS MANUAL MUST BE GIVEN T O THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANU AL AND SA VE FOR FUTURE REFERENCE.
2 W ARNING/SPECIAL NOTES W A R N I N G SA VE THESE INSTRUCTIONS W ARNING THE PROCEDURES IN THIS MANUAL SHOULD ONL Y BE PERFORMED BY A QUALIFIED TECHNICIAN. DO NOT SER VICE OR OPERA TE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERST ANDING THIS MANUAL AND THE OWNER’S MANUAL SUPPLIED WITH THE WHEELCHAIR.
3 T ABLE OF CONTENTS T A B L E O F C O N T E N T S TABLE OF CONTENTS SPECIAL NOTES ................................................ 2 SPECIFICA TIONS ............................................... 4 PROCEDURE 1 - GENERAL GUIDELINES .......... 7 REP AIR OR SERVICE INFORMA TION .
4 SPECIFICA TIONS S P E C I F I C A T I O N S SPECIFICATIONS PERFORMANCE R2 BASIC R2 250 series R2 ST ANDARD Speed (M.P .H.): 0 to 3.8 0 to 3.6 0 to 5.8 T urning Radius: > 23-inches > 23-inches > 23-inches Range (variable) 4 : 18-22 miles 12-14 miles 18-22 miles L Weight Limitation 5 : 250 lbs.
5 S P E C I F I C A T I O N S SPECIFICA TIONS PERFORMANCE R2 BASIC R2 250 SERIES R2 ST ANDARD Speed (M.P .H.): 0 to 3.8 0 to 3.6 0 to 4.0 T urning Radius: > 25.8-inches > 25.8-inches > 25.8-inches Range (variable) 3 : 17-22 miles 12-14 miles 12-16 miles L Weight Limitation 4 : 250 lbs.
6 SPECIFICATIONS NOTE: All specifications are approximate. RANGER II FWD - R2 JR INTEGRA TED SLING SEA T Seat Width Range: 14-inches Seat Depth Range: 16 to 18-inches - In 1-inch increments (17 and 18.
7 GENERAL GUIDELINES PROCEDURE 1 G E N E R A L G U I D E L I N E S W ARNING CONTROLLER SETTINGS FOR R2 JR Set-up of the Electronic Contr ol Unit is to be performed ONL Y by qualified technicians. Factory setting of the controller MUST be used for daily activities.
8 GENERAL GUIDELINES PROCEDURE 1 G E N E R A L G U I D E L I N E S WARNING/CAUTION LABEL LOCATION - MWD MODELS (R2 BASIC /R2 STANDARD /R2 250 SERIES ) CAUTION HIGH BACK CAPT AIN'S SEA TS ONL Y - Disconnect limit switch BEFORE re- moving seat - damage to seat can occur.
9 Push Bracket Crossbrace WARNING/CAUTION LABEL LOCATION - FWD MODELS (R2 BASIC /R2 STANDARD /R2 250 SERIES ) W ARNING Replacement con- troller MUST be SAME part number. Motor Assembly Controller (Back View) CAUTION HIGH BACK CAPT AIN'S SEA TS ONL Y - Disconnect limit switch BEFORE removing seat - dam- age to seat can occur.
10 WARNING/CAUTION LABEL LOCATION - FWD MODELS (R2 JR ) W ARNING Replacement con- troller MUST be SAME part number. Motor Assembly Controller (Back View) CAUTION Repositioning the motors WILL af- fect the stability and/or per for- mance of the wheelchair.
11 BATTERY WARNING LABEL LOCATION W ARNING This POSITIVE (+) RED Battery Cable MUST connect to the POSITIVE (+) Battery T e rminal(s)/Post(s), otherwise serious damage will occur to the electrical sys- tem. Refer to the Owner ’ s Manual. DO NOT remove this label.
12 (+) (-) FIGURE 1 - FIELD LOAD TEST Battery Charger Connector Digital V oltmeter FIELD LOAD TEST (FIGURE 1) NOTE: The following test can also be performed through the controller of the wheelchair along with a remote pro- grammer . Refer to the individual CONTROLLER MANUAL supplied with each wheelchair .
13 TROUBLESHOOTING PROCEDURE 2 T R O U B L E S H O O T I N G W ARNING ONL Y use distilled water when topping of f the battery cells. Most batteries are not sold with instructions. However, warnings are frequently noted on the cell caps. Read them carefully.
14 ELECTRO-MECHANICAL PARKING BRAKE TESTING (FIGURE 5) 1 . On the four-pin motor connector , locate the side by side connectors in the black housings. 2 . Set the digital multimeter to read ohms ( Ω ). 3 . Measure the resistance between the two (2) brake contacts.
15 This Procedure Includes the Following: Adjusting Flip-Up Removable Footboard Adjusting the Removable Footboard W ARNING After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.
16 Footplate Clamps Removable Footboard ADJUSTING DEPTH Mounting Positions Flat Head Screws Barrel Nut Barrel Nut DET AIL "A" Proper Footplate Clamp Position for MWD Wheelchairs Proper Footplate Clamp Position for FWD Wheelchairs ADJUSTING THE REMOVABLE FOOTBOARD NOTE:This footboard assembly is available on models built AFTER 3/1/00.
17 4. Remove the nut, flat washer and that secure the threaded arm on the height adjustment bracket to the footboard bracket. Refer to DET AIL “ B ” . 5. Perform one (1) of the following: A. MWD WHEELCHAIRS - Move the height adjust- ment bracket to one (1) of seven (7) height positions.
18 A R M S ARMS PROCEDURE 4 REPLACING ARMREST PADS (FIGURE 1) 1 . Remove the mounting screws that secures the front of the armrest pad to the armrest plate. 2 . Remove the mounting screw that secures the rear of the armrest pad and armrest insert to the armrest plate.
19 PROCEDURE 5 SEA T/BACK S E A T / B A C K Hex Bolts (Apply Loctite 242 and torque to 75-inch pounds) Locknuts Back Upholstery Washer Phillips Screw Tie Wrap Mounting Holes 7 .
20 8 . Slide the loose top half of the back cane through the new back upholstery . 9 . Using the mounted back cane as a guide, reinstall the two (2) hex bolts that secure the top half of the back cane to the bottom half of the back cane. NOTE: Make sure the back canes are mounted to the same height.
21 PROCEDURE 6 SEA T FRAME Locknuts Hex Bolts (Apply Loctite 242 and torque to 75-inch pounds) Bottom Half of Back Cane T op Half of Back Cane HOLE P AIR # 5 4 3 2 1 FIGURE 2 - ADJUSTING BACK HEIGHT FIGURE 1 - ADJUSTING SEA T DEPTH Phillips Screws Washer Plug Button Crossbrace Seat Extension T ube ADJUSTING SEAT DEPTH (FIGURE 1) 1 .
22 FIGURE 3 - CHANGING BACK ANGLE CHANGING BACK ANGLE (FIGURE 3) 1 . Flip the armrests up and out of the way . Refer to US- ING/ADJUSTING FLIP BACK ARMRESTS in PRO- CEDURE 4 of the owner's manual, part number 1080722.
23 FIGURE 4 - REPLACING BACK CANES 1 1. Securely tighten back upholstery to the new top half of the back cane with the phillips screw and washer . 1 2. Repeat STEPS 2-1 1 for the opposite side of the wheel- chair , if necessary . Bottom Half of Back Canes 1 .
24 ELECTRONICS FIGURE 1 - REPOSITIONING MKIV JOYSTICK - CAPT AIN ’ S SEA T S Adjustment Lock Hex Bolts (STEPS 3, 16) Spacers (STEPS 3, 17) Locknuts (STEPS 3, 17) Phillips Screw (STEPS 4, 14) Armrest.
25 MKIV Controller Locknuts FIGURE 2 - REMOVING/INST ALLING MKIV CONTROLLER - 16,18, 20-INCH WIDE MODELS Mounting Stud on Wheelchair Frame Washer Washer - MWD Only 14-inch Wide Models (FIGURE 3) REMOVING. 1 . Remove the front and rear shrouds. Refer to RE- MOVING/INST ALLING SHROUDS in PROCEDURE 10 of this manual.
26 FIGURE 3 - REMOVING/INST ALLING MKIV CONTROLLER - 14-INCH WIDE MODELS Left Hand Motor/Controller Connection Battery Wiring Harness and Controller Connection (BLUE) T ie-Wrap Wire Connector Support .
27 PROCEDURE 8 LIMIT SWITCH L I M I T S W I T C H DISCONNECTING/CONNECTING LIMIT SWITCH (FIGURE 1) NOTE: The following procedure is for High Back Captain's seat model wheelchairs only . CAUTION Disconnect limit switch BEFORE removing seat or damage to switch may occur.
28 FIGURE 2 - ADJUSTING LIMIT SWITCH 5 o Seat Angle 24 o Back Recline Angle 61 o Magnetic Protractor - (Will read 61 o when back recline angle is at 1 14 o relative to the seat frame) Upper Limit Switch Bracket Phillips Screws, Washers and Lock- nuts Actuator 11 4 o 5-3/4 inches PROCEDURE 8 LIMIT SWITCH L I M I T S W I T C H D.
29 W H E E L S PROCEDURE 9 WHEELS REPLACING PNEUMATIC TIRES/ TUBES - DRIVE WHEELS/CASTERS W ARNING DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT over- inflate the tires. Failure to follow these sug- gestions may cause the tire to explode and cause bodily harm.
30 6 . Examine the head of the hex screw and the locking tab washer . Make sure one (1) of the tabs on the locking tab washer is parallel with one (1) of the flats on the head of the hex screw .
31 2 . Apply a thin film of anti-seize compound one (1) inch in length to the end of the drive shaft. 3 . Reinstall drive wheel hub onto the gearbox drive shaft. NOTE: While installing the drive wheel hub onto the drive shaft, spin the drive wheel hub to evenly distribute the anti- seize compound over the entire drive shaft.
32 REPLACING CASTERS (FIGURE 4) 1. Remove the hex screw , washers and locknut that secure the caster to the fork. 2. Remove the caster from the fork. 3. Install Loctite 242 onto the hex screw . 4. Replace caster and reverse STEPS 1-3. 5. T orque the locknut to 120-inch pounds.
33 2. Remove rear shroud and rear storage compartment (if equipped) from the wheelchair . Refer to REMOVING/ INST ALLING REAR SHROUD AND REAR ST ORAGE COMP AR TMENT in this procedure of the manual. 3 . Perform one (1) of the following: A . INTEGRA TED SLING SEA T MODELS - Fold the wheelchair .
34 8 . Reinstall the front shroud onto the wheelchair . Refer to REMOVING/INST ALLING FRONT SHROUD in this procedure of the manual. FIGURE 1 - REMOVING/INST ALLING SHROUDS - MWD WHEELCHAIRS Front Shro.
35 PROCEDURE 10 SHROUDS S H R O U D S FWD Wheelchairs (FIGURE 2) REMOVING FRONT SHROUD. 1 . Unclip the retaining strap securing the front shroud and battery box to the wheelchair . 2 . Feed the retaining strap through the front shroud. 3 . Remove the front shroud from the wheelchair .
36 S H R O U D S SHROUDS PROCEDURE 10 FIGURE 2 - REMOVING/INST ALLING SHROUDS - FWD WHEELCHAIRS Front Shroud Phillips Screws Washers Rear Shroud 16,18,20-inch wide chairs.
37 ADJUSTING SEAT WIDTH - INTEGRATED SLING SEATS (FIGURE 1) 1 . If necessary remove the shrouds. Refer to REMOV- ING/INST ALLING SHROUDS in PROCEDURE 10 of this manual. 2 . Perform one (1) of the following: FWD WHEELCHAIRS - A . Remove the battery boxes from the wheelchair .
38 C R O S S B R A C E S MWD WHEELCHAIRS - A . Reinstall the battery tray onto the wheelchair . Re- fer to INST ALLING/REMOVING BA TTER Y TRA Y in PROCEDURE 14 of this manual. B. Reinstall the battery boxes onto the wheelchair . INST ALLING/REMOVING BA TTER Y BOXES in PROCEDURE 14 of this manual.
39 PROCEDURE 1 1 CROSSBRACES REPLACING CROSSBRACES - CAPTAIN'S SEATS (FIGURE 2 ) 1 . Remove the captain's seat from the wheelchair . Refer to REMOVING/INST ALLING CAPT AIN'S SEA T in PRO- CEDURE 5 of the owner's manual, part number 1080722.
40 PROCEDURE 1 1 CROSSBRACES C R O S S B R A C E S FIGURE 2 - REPLACING CROSSBRACES - CAPT AIN'S SEA TS Front of Wheelchair Note orientation of hex bolt, washers, coved washers and locknut for installation of new crossbraces.
41 B A T T E R I E S PROCEDURE 12 BA TTERIES This Procedure includes the following: Installing/Removing Batteries into/From Battery Boxes Connecting Battery Cables W ARNING Make sure power to the wheelchair is OFF be- fore per forming this procedur e.
42 PROCEDURE 12 BA TTERIES B A T T E R I E S CONNECTING BATTERY CABLES W ARNING NEVER allow any of your tools and/or battery cable(s) to contact BOTH battery terminal(s)/post(s) at the same time. An electrical short may occur and serious personal injury or damage may occur.
43 PROCEDURE 12 BA TTERIES B A T T E R I E S FIGURE 3 - CONNECTING BA TTERY CABLES - DIRECT MOUNT METHOD Orange Battery T erminal Cap POSITIVE (+) Battery T erminal/ Post U-1 Battery Gray Battery T er.
44 Battery Cable Battery Clamp Cover 2. Install battery clamp covers onto battery cables as follows (FIGURE 5): A . RED battery clamp cover onto RED battery cable. B. BLACK battery clamp cover onto BLACK bat- tery cable. NOTE: Only one (1) battery cable and battery clamp cover are shown for clarity .
45 9. Install the battery box(es) into the wheelchair . Refer to INST ALLING/REMOVING BA TTER Y BOX(ES) in the PROCEDURE 13 - FWD MODELS or PROCE- DURE 14 - MWD MODELS of this manual. NOTE: New Battery(ies) MUST be fully charged BEFORE using, otherwise the life of the battery(ies) will be reduced.
46 Install the batteries. Refer to INST ALL- ING/REMOVING BA TTER Y BOXES in this procedure of the manual. Position the battery tray for use. Re- fer to BA TTER Y TRA Y in this pro- cedure of the manual. Install the electronics. Refer to PREP ARING MKIV JOYSTICK FOR USE in PROCEDURE 7 of this manual.
47 FIGURE 2 - TRANSPORTING RANGER II FWD - CAPT AIN'S SEA TS Unfolding/Folding - Captain's Seat (FIGURE 2) UNFOLDING. 1. Push down on the push brackets until they are flush with the pivot links on the crossbraces. 2. Assemble the wheelchair .
48 WHEN TO CHARGE BATTERIES (FIGURE 5) NOTE: As a general rule, batteries should be recharged daily to assure longest possible life and minimize required charging time. In fact, a battery ’ s life is extended if the charge level is maintained well above a low condition.
49 FIGURE 6 - CHARGING BA TTERIES Required Items: TOOL QUANTITY COMMENTS Battery Charger 1 Supplied ✪ ✪ ✪ ✪ ✪ Extension Cord 1 Not Supplied ✪ 3-prong plug, 15 ampere current rating; industrial type 1. Attach the battery charger connector to the charger cable/battery harness.
50 INSTALLING/REMOVING BATTERY BOXES W ARNING NEVER unplug the battery cables by pullling on the wires. Unplug the battery cables by pulling on the connector ONL Y. Otherwise, injury or dam- age may occur. NOTE: T o remove the battery boxes, reverse the follow- ing procedure.
51 Rear Shroud Front Battery Box Rear Battery Box Retaining Strap Front Shroud Battery Connections on Side of Wheelchair Frame Slot FIGURE 8 - INST ALLING/REMOVING BA TTERY BOXES R2 JR Battery T ray D.
52 Mounting Slots Hanger Bracket Battery T ray Pins Battery T ray Pivot Pins R2 BASIC AND R2 ST ANDARD R2 JR R2 BASIC AND R2 ST ANDARD R2 JR Battery T ray Notch Notch Battery T ray Stop l Battery Brac.
53 INSTALLING (FIGURE 12). 1 . Line up mounting holes in the new /existing battery tray with the mounting holes in the battery tray hanger bracket. 2 . Position one (1) of the washers between the battery hanger bracket and the new /existing battery tray .
54 B. WHEELCHAIR NOT EQUIPPED WITH FLIP-UP REMOV ABLE FOOTBOARD - Remove the front hex screw that secures the existing left battery tray bracket to the wheelchair frame. 4. Remove the locknut that secures existing left battery tray hanger bracket and MKIV controller from the wheelchair .
55 FOR MODEL R2 JR (FIGURE 17 ). NOTE: Right and left is determined by sitting in wheel- chair . 1. Remove the footrests. Refer to INST ALLING /RE- MOVING FOOTRESTS in PROCEDURE 3 of the Owner's Manual, part number 1080722. 2. Remove the front and rear shrouds.
56 C. Connect the limit switch. Refer to DISCONNECT- ING/CONNECTING LIMIT SWITCH in this PRO- CEDURE 8 of this manual. 17 . Reinstall the battery boxes. Refer to INST ALLING/ REMOVING BA TTER Y BOXES in this procedure of the manual. 18 . If necessary , install the front and rear shrouds.
57 14-inch Wide Models (FIGURE 19) 1. Remove the shrouds. Refer to REMOVING/INST ALL- ING SHROUDS in PROCEDURE 10 of this manual. 2. Remove the battery boxes. Refer to REMOVING/IN- ST ALLING THE BA TTER Y BOXES in PROCEDURE 12 of this manual. 3. Cut the tie wrap that secure the following connections to the wire connector support: A.
58 FIGURE 19 - REPLACING WIRING HARNESS - 14-INCH WIDE MODELS Left Hand Motor and Controller Connection Battery Wiring Harness and Controller Connection (BLUE) Wire Connector Support MKIV Controller S.
59 1. Remove the battery boxes. Refer to INST ALLING/ REMOVING BA TTER Y BOXES in this procedure of the manual. 2. Perform one (1) of the following: A. WHEELCHAIR EQUIPPED WITH FLIP-UP RE- MOV ABLE FOOTBOARD - Remove the hex screws and spacers that secure the battery tray hanger bracket and footboard mounting bracket to the wheelchair frame.
60 REAR MOTOR MOUNTING POSITION MIDDLE MOTOR MOUNTING POSITION FRONT MOTOR MOUNTING POSITION FIGURE 20 - REPOSITIONING MOTORS Wheelchair Frame LONG Socket Screws (Apply Loctite 242 and torque to 60-inch pounds) (STEPS 6, 8) Motor/ Gearbox SHORT Socket Screws (Apply Loctite 242 and torque to 60- inch pounds) (STEPS 6, 8) 8.
61 FIGURE 21 - REPLACING CLUTCH HANDLES - RANGER II FWD BASIC Tip (STEPS 2, 6, 8) Outside of Wheelchair Motor/ Gearbox Clutch Handle (STEPS 4, 7) Clutch Handle (STEP 9) Pin (STEPS 3, 10) Detent Ball Motor/Gearbox DET AIL "A" 5. Perform one (1) of the following: A.
62 1 9 . Perform one (1) of the following: A. WHEELCHAIR EQUIPPED WITH FLIP-UP RE- MOV ABLE FOOTBOARD - Reinstall the hex screws and spacers that secure the battery tray hanger bracket and footboard mounting bracket to the wheelchair frame. Use Loctite 242 and torque to 156-in/lbs.
63 FIGURE 23 - REPLACING MOTOR/GEARBOX - RANGER II FWD - ST ANDARD Wheelchair Frame LONG Socket Screws (Apply Loctite 242 and torque to 60- inch pounds) (STEPS 8, 10) Motor/ Gearbox STEPS 4, 6, 13,14,.
64 This Procedure Includes the Following: Assembling Ranger II MWD When to Charge Batteries Charging Batteries Replacing Batteries Installing/Removing Battery Boxes Battery Tray Replacing Wiring Harne.
65 MWD WHEELCHAIRS M W D W H E E L C H A I R S PROCEDURE 14 Install the battery tray and batteries. Refer to INST ALLING/REMOVING BA TTER Y TRA Y and INST ALLING/ REMOVING BA TTER Y BOXES in this procedure of the manual. FIGURE 2 - ASSEMBLING RANGER II MWD - CAPT AIN'S SEA TS Install the electronics.
66 Battery Gauge Display MKIV X, A OR A+ JOYSTICK FIGURE 5 - WHEN TO CHARGE BA TTERIES NOTE: MKIV X Shown. WHEN TO CHARGE BATTERIES (FIGURE 5 ) It is advantageous to recharge daily rather than only when necessary . In fact, a battery ’ s life is extended if the charge level is maintained well above a low condition.
67 REPLACING BATTERIES W ARNING The following pr ocedure should be per formed only by aqualified technician. Most batteries are not sold with instructions. How- ever, warnings are frequently noted on the cell caps. Read them carefully, otherwise injury or damage can occur.
68 INSTALLING/REMOVING BATTERY BOXES (FIGURE 7) Installing NOTE: T o remove the battery boxes from the wheelchair , reverse the following procedure. W ARNING If the wheelchair is equipped with the removable footboard AND it is installed in the heighest posi- tion, it is necessary to remove the footboard plate BEFORE removing the battery boxes.
69 Retaining Strap Clip Battery Connections on Side of Wheelchair Frame Retaining Strap FIGURE 7 - INST ALLING/REMOVING BA TTERY BOXES Front Battery Box Front of the Wheelchair Rear Battery Box Battery Box Leads 6. If necessary , reinstall the removeable footboard.
70 Battery T ray Hanger Bracket Battery T ray Pins "FRONT" Label FIGURE 8 - BA TTER Y TRA Y BA TTERY TRA Y FOR WHEELCHAIRS NOT EQUIPPED WITH WEIGHT SHIFT BASIC TIL T BA TTERY TRA Y FOR WHEEL.
71 Changing Width of Battery Tray (FIGURE 9) NOTE: This procedure is only necessary when changing the width of the wheelchair . 1. Remove the battery tray from the wheelchair . Refer to INST ALLING/REMOVING BA TTER Y TRA Y in this procedure of the manual.
72 FIGURE 10 - REPLACING WIRING HARNESS Charger Cable Mounting Bracket Wiring Harness T o Controller (STEPS 3, 15) MKIV Joystick Controller Phillips Screws (STEPS 4, 1 1) Phillips Bolts (STEPS 6, 13) .
73 STABILIZERS FIGURE 12 - ADJUSTING ST ABILIZERS - SPRINGS Measure This Height Stabilizer NOTE: If the user's approximate weight is not listed above, use the HIGHEST listed approximate weight closest to user's weight as a starting point to adjust the stabilizer spring.
74 ADJUSTING STABILIZER FOR USER PREFERENCE Adjusting Type A Stabilizer Assembly for User Preference (FIGURE 13) NOTE: Refer to ST ABILIZER INDENTIFICA TION in the beginning of this section to determine correct sta- bilizer assembly .
75 Adjusting Type C Stabilizer Assembly for User Preference (FIGURE 15) NOTE: Refer to ST ABILIZER INDENTIFICA TION in the beginning of this section to determine correct sta- bilizer assembly . 1. Rotating the locknut that is located on top of the lower spring provides one (1) of the following: A.
76 Replacing Stabilizer Cylinders for Type C Stabilizer Assemblies (FIGURE 17) NOTE: Refer to ST ABILIZER INDENTIFICA TION in the beginning of this section to determine correct stabilizer assembly . 1. Place a 1/2-inch block underneath drive wheel. 2.
77 FIGURE 18 - REPLACING ST ABILIZER WHEEL FOR TYPE A AND TYPE B ST ABILIZER ASSEMBLIES Stabilizer Wheel Hex Bolt Locknut Spacers Mount Stabilizer Wheel in TO P Mounting Hole Only Stabilizer Plates 2. Remove existing stabilizer wheel from the wheelchair .
78 15 . Repeat STEPS 2-14 for the opposite side of the wheel- chair , if necessary . 16 . Tighten the jamnut on the stabilizer cylinder . W ARNING Stabilizers MUST be adjusted BEFORE use, oth- erwise they will NOT operate properly. 17. Adjust the front stabilizer(s).
79 FIGURE 22 - REPLACING MOTOR/GEARBOX - RANGER II MWD BASIC Wheelchair Frame LONG Socket Screws (Apply Loctite 242 and torque to 60-inch pounds) (STEPS 1 1, 13) Battery T ray Mounting Bracket Motor/ .
80 NOTE: Make sure the detent ball on the pin is fully visible. 16 . Repeat STEPS 3-15 for the opposite side of the wheel- chair , if necessary . 17 . Reinstall the drive wheels onto the wheelchair . Refer to REMOVING/INST ALLING DRIVE WHEELS in PROCEDURE 9 of this manual.
81 FIGURE 23 - REPLACING MOTOR/GEARBOX - RANGER II MWD ST ANDARD LONG Socket Screws (Apply Loctite 242 and torque to 60-inch pounds) (STEPS 9, 1 1) Dust Cover Hex Bolt Washer Crossbrace Locknut STEPS .
82 NOTES NOTES N O T E S.
83 LIMITED WARRANTY PLEASE NOTE: THE W ARRANTY BELOW HAS BEEN DRAFTED TO COMPL Y WITH FEDERAL LA W APPLICABLE TO PRODUCTS MANUF ACTURED AFTER JUL Y 4, 1975.
Invacar e Corpo ration www .in vacare.com USA Canada One Invacare W ay 5970 Chedworth W a y Invacar e and "Y es, you can" are trademarks of Invacare Elyria, Ohio USA Mississauga, Ontario C orporation. 44036-2125 L5R 3T9, Canada © 2000 Invacar e Corporation 800-333-6900 905-890-8838 F orm No.
デバイスInvacare Ranger II250 SERIESの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Invacare Ranger II250 SERIESをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはInvacare Ranger II250 SERIESの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Invacare Ranger II250 SERIESの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Invacare Ranger II250 SERIESで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Invacare Ranger II250 SERIESを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はInvacare Ranger II250 SERIESの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Invacare Ranger II250 SERIESに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちInvacare Ranger II250 SERIESデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
