IOGearメーカーGBS301の使用説明書/サービス説明書
ページ先へ移動 of 44
Bluetooth to Serial Adapter Bluetooth to Serial Adapter Bluetooth to Serial Adapter Bluetooth to Serial Adapter Bluetooth to Serial Adapter User Manual (GBS301) ®.
IOGEAR’s Bluetooth serial adapter brings wireless Bluetooth technology to your RS-232 serial equipment, allowing you to eliminate conventional cables. With a maximum range of 330 ft (100 meters), you are no longer bound to cable length limitations or messy cables.
T able of Contents Package Contents.............................................................................................. 2 Features........................................................................................................... 3 System Requirements.
2 Package Contents This package contains: 1 Bluetooth serial adapter 1 Null modem adapter 1 Power adapter 1 User manual 1 Quick Start Guide 1 Warranty/Registration card.
3 Features · Eliminates messy cables, allowing you to communicate to serial RS-232 devices wirelessly · Easily accessib le DIP s witches for f ast and easy configuration without using HyperT er mina.
4 • Device with DB-9 Connector and compliant with RS-232 protocol System Requirements Note: Due to the various communication protocols and drivers involved, this adapter may not work with RS-232 modems, mice, keyboards, cell phones, and devices using proprietary communication protocols.
5 5 Introduction 1. IOGEAR logo, mark of Quality 2. Power jack 3. Status LED 4. DIP Switches 5. RS-232 interface 3.
6 6 Bluetooth Serial Adapter Pin-out Pictorial Introduction.
7 Pictorial Introduction 7 Null Modem Adapter Pin-out.
8 8 Operation Factory Settings When using the Bluetooth serial adapter with your serial devices, you must make sure that all the settings below match on both devices; otherwise, you may encounter problems communicating.
9 Switfches 1-3 9 Operation DIP Switches 1, 2, and 3 are used to configure the baud rate. Note: Most computer serial ports only support baud rate up to 115200.
Operation 10 DIP Switch 4 is used to set the serial adapter as master or slave: Master mode: Switch 4 ON Slave mode: Switch 4 OFF Master Mode If you are interconnecting two IOGEAR Bluetooth adapters, you must set one of them to master and the other to slave.
11 Basic Configuration 11 The Bluetooth serial adapter has built-in dip switches for fast and easy configuration. If you would like to change any of the default settings, consult the Advanced Configuration section on page 22. Using table 1 on page 9, set the baud rate on the Bluetooth serial adapter by using the on-board DIP switches.
12 When using the Bluetooth serial adapter with a Bluetooth-enabled device (PC/PDA), you must set the Bluetooth serial adapter in slave mode (Switch 4 = Off). Plug in the Bluetooth serial adapter to your serial device. If your device has a male RS232 interface, use the included null modem adapter.
13 13 Use your Bluetooth software to search for Bluetooth devices in range. Once the Bluetooth serial adapter is detected, pair to it. If prompted for a PIN code, enter “1234” (without the quotes). Once paired, establish a connection using the Bluetooth serial port profile (SPP).
Widcomm Bluetooth Software 1. Open My Bluetooth Places and Search for Devices in Range 14 Basic Configuration.
15 2. When found, pair to the Bluetooth serial adapter. The default PIN code is “1234” 3. Once paired, the unit will display the services available.The service offered by this unit is the Serial Port Profile (SPP).T o estab lish a connection, right-click on it and select “Connect to Bluetooth Serial Po r t.
4. Once connected, you will see this window indicating the COM port number used for connection with the Bluetooth serial adapter. In our example below , this is COM 4, but most likely it will be different in your case.
17 1. Auto-pairing 2. Back-to-Back 3. Configuration Mode Interconnecting two IOGEAR Bluetooth serial adapters Basic Configuration SCENARIO 2: When interconnecting two IOGEAR Bluetooth serial adapters,.
14 Note: If you have previously paired to the Bluetooth serial adapter(s), make sure to follow the unpairing procedure on page 29 before attempting to connect to a new device.
15 Method 2 – Back to Back Pairing Follow this procedure to pair two (2) Bluetooth Serial Adapters. 19 1 Set one serial adapter to Master (switch 4 = ON), and the other to Slave (switch 4 = OFF) Upo.
20 Disconnect both serial adapters and Power them OFF 7 4 Back-to-Back Connect the serial adapters back-to-back, using the included Null Modem adapter Power ON both Serial adapters 5 Power ON Power OFF 7 Almost instantly , the Red/Blue LED will light up and sta y solid; this indicates successful pair ing of the two serial adapters.
21 After successful connection is made, the blue LED on both serial adapters will turn off and remain Y ou ma y now connect each adapter to your desired serial device f or communication.
The Bluetooth serial adapter has an embedded configuration menu that allows you to change settings for your specific application. This menu can be accessed via HyperT erminal (Windows systems).
Configuring Serial Adapter 23 Advanced Configuration Set the Baud rate on the Serial adapter to 9600 (see table 1 on page 9) 1 Set baud rate Plug the Bluetooth serial adapter to an available serial port on your computer (Do NOT power on the serial adapter yet).
18 Note: HyperT er minal may also be found under Start Programs Accessories C o m m u n i - cations HyperT er minal 24 Advanced Configuration.
When prompted for the COM port number being used, make sure to select the correct one. If you only have one physical com port in your computer, this will probably be COM 1 However, if you’re unsure, contact your computer/motherboard manufacturer. In the case above, we have several COM ports available, and we are using COM 1.
20 26 Make sure to set your settings as shown on the window below: 5 Port Settings Advanced Configuration.
21 27 Once you have initiated your HyperT er minal session, pow er ON the Serial adapter. It will display the words “PR” to indicate it is in configuration mode.
28 Advanced Configuration 7 Make Changes Make your selection from the menu to change any desired settings. F or more details on the HyperT e rminal configuration menu, please see the Appendix on page 31. 8 Exit and apply changes T o apply an y changes, you must select option E (Exit configuration) and accept the changes.
29 Unpairing Procedure Method 1 1. Power OFF the serial adapter 2. Change the position of Dip Switch 4 3. Power ON the serial adapter.The LED will blink once, indicating successful unpairing. 4. Power OFF the serial adapter 5. Change dip switch 4 back to its original position 6.
30 Specifications.
31 IMPORT ANT NOTE: As you look at the options listed below , please keep in mind that in order to apply any changes made, you must: · Select option E (Exit configuration) and type “Y” to accept .
32 IOGEAR GBS301 CONFIGURA TION MENU 1. Search for Bluetooth adapter 2. Change local device name 3. Set authentication mode 4. Set pin key 5. Set encryption mode 6. Set baud rate 7. Change uart settings 8. Display device settings C. Clear pairing information D .
33 Option 1: Search for Bluetooth adapter Use this option to search for another IOGEAR Bluetooth serial adapter. This option is only available if device set as Master. Keep in mind that the other serial adapter must be set to slave in order to be discovered.
34 Option 4: Set pin key The default PIN key for the serial adapter is “1234”. If you wish to change this to something else, use this option Option 5: Set encryption mode Use this option to enable/disable encryption mode. For example, there are some applications that might not work properly if encryption is enabled.
35 Option 6: Set baud rate The dip switches on the serial adapter allow you to set baud rates ranging from 9600 to 921600. If you need to use a lower baud rate – like 2400bps or 4800bps – use this option. The baud rates available for this unit are listed below: Baud rate setting 0.
36 Option 7: Change uart settings For certain applications, you might need to change the default UART settings. Below are the available options for this adapter: Parity : None, Odd, Even Stop bits: 1, 2 In case you are w ondering, UAR T stands for Univ ersal Asynchronous Receiver/T ransmitter .
37 Option D: Display firmware version Displays the firmware version of the Bluetooth serial adapter; this is mostly used for troubleshooting purposes Option F: Restore factory settings Use this option to restore all values to their factory settings.
38 T ec hnical Support If you need technical support, please check out our IOGEAR T ech Info Library (T .I.L.) at www.iogear.com/support for the latest tips, tricks, and troubleshooting. The IOGEAR T .I.L. was designed to provide you with the latest technical information about our products.
39 Radio & TV Interference Statement W ARNING!!! This equipment generates , uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
40 IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY FOR DIRECT , INDIRECT , SPECIAL, INCIDENT AL OR CONSEQUENTIAL D AMA GES RESUL TING FROM THE USE OF THE PRODUCT , DISK, OR ITS DOCUMENT A TION EXCEED THE PRICE P AID FOR THE PRODUCT .
41 CE Safety Statement This device has been tested and found to comply with the requirements set up in the council directive on the approximation of the law of member states relating to EMC Directiv e 89/336/EEC, Low V oltage Directive 73/23/EEC and R&TTE Directiv e 99/5/EC .
23 Hubble • Irvine, CA 92618 • (P) 949.453.8782 • (F) 949.453.8785 • www.iogear.com Contact inf o. ®.
デバイスIOGear GBS301の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
IOGear GBS301をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIOGear GBS301の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IOGear GBS301の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IOGear GBS301で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IOGear GBS301を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIOGear GBS301の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IOGear GBS301に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIOGear GBS301デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。